Post on 23-Jun-2021
transcript
ININ
FACULTAD DE INGENIERÍA
CENTRO INTERAMERICANO DE RECURSOS
DEL AGUA
“TRATAMIENTOS AVANZADOS
PARA LA REMOCIÓN DE UN COLORANTE
DE ORIGEN TEXTIL”
T E S I S
QUE PARA OBTENER EL GRADO DE
DOCTORA EN CIENCIAS DEL AGUA
PRESENTA
M. EN C. AMB. PERLA TATIANA
ALMAZÁN SÁNCHEZ
UNIVERSIDAD AUTÓNOMA DEL ESTADO DE
MÉXICO
DIRECTORES:
DRA. IVONNE LINARES HERNÁNDEZ
DR. MARCOS JOSÉ SOLACHE RÍOS
DRA. VERÓNICA MARTÍNEZ MIRANDA
TOLUCA, ESTADO DE MÉXICO, 12 DE AGOSTO DE 2016
“Tratamientos avanzados para la remoción de un colorante de origen textil”
EL PRESENTE TRABAJO SE DESARROLLÓ EN EL LABORATORIO DE
CALIDAD DEL AGUA DEL CENTRO INTERAMERICANO DE RECURSOS
DEL AGUA (CIRA) DE LA FACULTAD DE INGENIERÍA DE LA UNIVERSIDAD
AUTÓNOMA DEL ESTADO DE MÉXICO COMO PARTE DEL PROYECTO
CONACYT 219743: “TRATAMIENTOS AVANZADOS Y SUSTENTABLES
PARA LA REMOCIÓN DE COLORANTES DE ORIGEN TEXTIL”.
ASÍ COMO EN DEPARTAMENTO DE QUÍMICA DE LA GERENCIA DE
CIENCIAS BÁSICAS DEL INSTITUTO NACIONAL DE INVESTIGACIONES
NUCLEARES (ININ), COMO PARTE DEL PROYECTO CB-505 “PARÁMETROS
QUE INFLUYEN SOBRE LA SEPARACIÓN DE ESPECIES NUCLEARES,
INERTES O MICROBIOLÓGICAS CONSIDERADAS CONTAMINANTES DE
MEDIOS ACUOSOS POR COMPUESTOS DE NATURALEZA VARIADA Y
MECANISMOS ASOCIADOS”
Perla Tatiana Almazán Sánchez I
“Tratamientos avanzados para la remoción de un colorante de origen textil”
AGRADECIMIENTOS
Perla Tatiana Almazán Sánchez II
“Tratamientos avanzados para la remoción de un colorante de origen textil”
A la Universidad Autónoma del Estado de México, por brindarme la oportunidad
de formar parte de tan importante institución.
Al Centro Interamericano de Recursos del Agua de la Facultad de Ingeniería, a la
Coordinadora del Doctorado en Ciencias del Agua la Dra María Vicenta Esteller Alverich,
así como a las Licenciadas Ivania Alvirde y Nancy Vilchis. Así como a todo el personal
del Centro Interamericano de Recursos del Agua, al Ing. Polo, Liz, Don José Luis.
A la Coordinadora de Estudios Avanzados de la Facultad de Ingeniería la Dra.
María del Carmen Jiménez Moleón, y a las Licenciadas Juanita Fabila, María del Carmen
García y Dalia Verdier.
Al Laboratorio de Calidad del Agua del Centro Interamericano de Recursos del
Agua. (CIRA), en cuyas instalaciones se desarrolló este trabajo de investigación, a la Jefa
del Laboratorio M. en C. Ana Elisa Alcántara por todas las facilidades brindadas.
Al Instituto Nacional de Investigaciones Nucleares (ININ) en cuyas instalaciones
se llevó a cabo este trabajo de investigación. A la Jefa del Departamento de Química, M.
en C. Gloria Irene Carmona Chit, Catalina Ovalle, a los técnicos Iris, Marcelino y Elvia,
así como a cada uno de los maestros y doctores que pertenecen al Departamento.
Al Laboratorio de Investigación y Desarrollo de Materiales Avanzados (LIDMA),
Campus el Rosedal, Facultad de Química, UAEM, al Dr. Enrique Vigueras Santiago, por
las facilidades prestadas y su apoyo en el uso del equipo de Infrarrojo.
Al Consejo Nacional de Ciencia y Tecnología (CONACYT) por el financiamiento
a través del número de proyecto 219743 “Tratamientos Avanzados y Sustentable”, así
como por la beca otorgada durante los estudios de doctorado y por la beca Mixta para la
realización de la estancia internacional (CVU/ No Becario: 413703/257364).
Al Consejo Mexiquense de Ciencia y Tecnología (COMECYT), por la beca
otorgada para realizar el proceso de titulación para la obtención de grado, con número de
folio 16BTID0013
Perla Tatiana Almazán Sánchez III
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Al Dr. Manuel Rodrigo Rodrigo y al Dr. Salvador Cotillas Soriano por su apoyo en
la realización de la estancia de investigación en el Departamento de Ingeniería Química de
la Universidad de Castilla-La Mancha, Ciudad Real, España. A los estudiantes y personal
del Laboratorio de Ingeniería Electroquímica y Medioambiental, del Laboratorio de
Catálisis y del Instituto de Tecnología Química y Medioambiental: Inma, Yeray,
Alexandra, Martín, María, María José M., Pilar, Leo, Yoli, Conchi, Jorge, Julia, José
Fernando, Nuria, María José, Estela, Ana, David, Silvia, Esperanza, Sandra, Paula, Ivan.
Muchas gracias por su grata compañía durante la estancia, por su gran apoyo durante los
últimos días, sin su ayuda no lo hubiera logrado.
Al Dr. Mario Esparza y al Dr. Cheikh Fall por sus observaciones, comentarios e
importantes aportaciones que realizaron cada semestre para mejorar este trabajo de
investigación.
A la Dra. Edith Gutiérrez por su apoyo como sinodal en el examen final.
Al Dr. Iván G. Martínez Cienfuegos y al Ing. Eduardo González Mora por su apoyo
y asesoría en la construcción del concentrador parabólico compuesto CPC-2D.
A mis directores de tesis, la Dra. Ivonne Linares Hernández, el Dr. Marcos Solache
Ríos y la Dra. Verónica Martínez por su apoyo incondicional durante los estudios de
doctorado, sin su asesoría este proyecto no se hubiera llevado acabo.
Dra. Ivonne muchas gracias por su confianza, por enseñarme que siempre podemos
dar lo mejor de nosotros, que los límites pueden existir pero que la palabra imposible no,
por tener una palabra de ánimo cuando las cosas no parecían ir bien, por ayudarme a crecer
profesional y personalmente, pero sobre todo por su amistad, su compañía durante estos
seis años siendo mi directora de tesis de licenciatura, maestría y doctorado, ha sido un gran
honor trabajar con usted.
Dra. Vero gracias por todos estos años de aprendizaje, que me han ayudado a
crecer, por sus consejos en momentos difíciles, por su amistad y por siempre recordarme
que cuando tenemos disposición y nos esforzamos las cosas se dan y ocurren siempre para
bien. Ha sido un honor trabajar con usted durante estos seis años.
Perla Tatiana Almazán Sánchez IV
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Dr. Marcos gracias por compartir tu conocimiento, por confiar en mí en tan poco
tiempo y por darme la oportunidad de realizar la tesis en el ININ, ha sido un gran honor
trabajar estos tres años con una persona como tú que me ha enseñado que la humildad es
la mayor virtud que podemos tener como seres humanos, gracias por tu amistad también.
A mis compañeros de generación del Doctorado en Ciencias del Agua 2013-2016:
Lupita, Norma, Marce, Estela, Edith, Saúl y Miguel Ángel, por ser una grata compañía en
esta aventura.
A la Dra. Guadalupe Vazquez Mejía. Lupita gracias por tu amistad, por tu ayuda,
por tus asesorías, por siempre apoyarme y escucharme, hemos vivido de todo durante el
doctorado, alegrías, lágrimas, desvelos, horas en el laboratorio, experimentos fallidos, en
fin toda una vida que contar.
Al M. en C. Francisco Lara. Paco gracias por tu amistad, por tu ayuda
desinteresada, por tu calidez humana, por esas largas pláticas y por siempre alegrar el
laboratorio con tus brillantes ideas. Tu ayuda fue vital para construir el concentrador.
A todos los estudiantes de la Maestría y Doctorado en Ciencias del Agua por
compartir cientos de horas en el laboratorio, por las convivencias, por todas las
conversaciones y por ese buen ambiente laboral. A Ericka, Adriana, Lili, Brendita, Ceci,
Frida, Aranzazu, Javi, Carlos, Sergio Alcaraz, Sergio Ríos, Vicky.
Al equipo Linares-Martínez: Ran, Monse, Dani, Ale, Caro, Juan Carlos, Gaby,
Lupita Fonseca, hemos hecho un buen equipo de trabajo. Gracias por todas sus
aportaciones y comentarios, pero sobre todo por nunca perder el sentido del humor, fue
muy grato compartir este tiempo con ustedes.
A las M. en C. Monserrat Castañeda y Daniela Hernández. Monse y Dani gracias
por toda su ayuda en el laboratorio, la verdad es que no tengo con que agradecer todo lo
que han hecho por mí. Gracias por su amistad y por siempre escucharme.
Al M. en C. Ranulfo Gómez. Ran gracias por tener un buen consejo en cada
situación complicada, agradezco mucho su amistad y su desinteresada disposición por
ayudar siempre.
Perla Tatiana Almazán Sánchez V
“Tratamientos avanzados para la remoción de un colorante de origen textil”
A la M. en C. Q. Nancy Lara, a la Q. Dulce Hernández y a la Q. Alma Jiménez.
Chicas muchas gracias por preocuparse por mí, por su amistad sincera y desinteresada, por
su ayuda, por su apoyo y por creer en mí. La química fue un camino que iniciamos juntas
hace diez años y que nos unió para siempre.
A la M. en C. Amb. Gratia Deii Flores. Deii gracias por siempre tener una solución
a mis problemas, por siempre tener una respuesta a mis preguntas, por tu apoyo
incondicional, por motivarme a seguir adelante aún a contracorriente, de verdad que tú
ayuda ha sido vital y muy importante para mí, pero sobre todo gracias por tu amistad.
Al Maestro Boni, al Dr. Fernando Ureña y a los becarios del Instituto Nacional de
Investigaciones Nucleares: Yaneli, Jorge, David, Yes, Yanet, Sandy, Dianita, Manolo,
Abraham, Araceli, Gilberto, Ale, Nidia. Gracias por su amistad y apoyo en el laboratorio.
A Rosa Salinas y Paul Marín por permitirme ser su asesora de tesis.
Perla Tatiana Almazán Sánchez VI
“Tratamientos avanzados para la remoción de un colorante de origen textil”
DEDICATORIAS
Perla Tatiana Almazán Sánchez VII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Todo este trabajo lo dedico a Dios, por ensenarme que tus pensamientos son
mejores que los míos y que siempre sabes lo que es mejor para mí. A veces no entiendo
por qué suceden algunas cosas pero al final veo que todo fue para y por mi bien. Todo lo
debo a ti, sin tu voluntad, sin tu ayuda, pero sobre todo sin tu presencia en mi vida nada de
esto hubiese sido posible.
A mis papás Evita y Justino: Gracias papi y mami, ustedes más que nadie saben
todo que he vivido, pues en cada triunfo, cada fracaso, alegrías, tristezas, siempre
estuvieron ahí de manera incondicional. A ustedes dedico todo éxito porque me han
enseñado que todos nuestros esfuerzos y acciones siempre tienen su recompensa. Gracias
por todo lo que hacen por mí y por todo su amor, soy la mujer más afortunada y bendecida
por tenerlos. Los amo.
A Joel gracias por siempre motivarme a seguir adelante, por cuidarme y estar al
pendiente de mí. Te amo, eres el mejor y único hermano que Dios me pudo dar.
A Valeria, mi pequeña sobrina, eres esa alegría que le hacía falta a nuestras vidas,
ese motorcito que nos incita a ser mejores personas para ti. Antes de tu nacimiento no sabía
la gran bendición que Dios tenía para nuestra familia, ahora que estás con nosotros le
agradezco inmensamente porque Él nunca se equivoca y tú has sido una de las mejores
cosas que han llegado a mi vida. Te amo Vale.
A mi abuelita Lolita, gracias por todas sus oraciones, es una gran bendición para
mí, un gran ejemplo de fortaleza, gracias por todo lo que hace por nosotros.
A mi abuelito Richar, porque sus consejos han quedado grabados en mi corazón y
su ejemplo de honradez, fortaleza y fe me acompañan todos los días.
A mis tías, tíos, primos y primas por ser un gran apoyo para mi familia.
A mis bellos sobrinos y sobrinas por su enorme amor y cariño.
A Thelma y Soni gracias por siempre estar para mí y no dudar nunca en ayudarme,
saben que son mis hermanas y las quiero mucho.
Perla Tatiana Almazán Sánchez VIII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
No quiero decir que ya haya logrado todo, ni que ya
haya alcanzado la perfección. No lo he logrado, pero me
concentro y fijo la mirada en lo que tengo por delante, y
así avanzo hasta llegar al final de la carrera para recibir
el premio celestial al cual Dios nos llama.
Filipenses 3:12-13
Perla Tatiana Almazán Sánchez IX
“Tratamientos avanzados para la remoción de un colorante de origen textil”
RESUMEN
Perla Tatiana Almazán Sánchez X
“Tratamientos avanzados para la remoción de un colorante de origen textil”
RESUMEN
En el presente trabajo se muestran los resultados obtenidos del estudio realizado para
remover un colorante en solución acuosa y del tratamiento de un agua residual
provenientes de una lavandería de acabados de prendas de mezclilla empleando materiales
naturales y modificados con hierro y cobre, que fueron aplicados en los tratamientos
avanzados de adsorción y oxidación avanzada por Fenton y foto-Fenton heterogéneo.
En una primera etapa, se realizó la modificación electroquímica de una arcilla y un carbón
activado utilizando electrodos de Fe y Cu a valores de pH 7 y 2 respectivamente. Los
materiales fueron caracterizados por microscopía electrónica de barrido (MEB), análisis
elemental (EDS), difracción de rayos X (DRX) y área específica BET, mostrando que el
pH óptimo para modificar la arcilla con Fe y Cu fue 7, mientras que para el carbón
modificado con cobre fue a pH 2, el análisis elemental indicó que bajo las anteriores
condiciones se encuentra un mayor contenido de los metales evaluados. El área específica
para la arcilla natural (Mt-KSF) y la modificada con Fe (Mt-Fe-7) y cobre (Mt-Cu-7) a pH
7 fue de 5.97, 131.30 y 78.44 m2/g, mientras que para el carbón natural y el modificado
con cobre a pH 2 fue de 654.85 y 647.61 m2/g.
En una segunda etapa se realizaron las pruebas de adsorción en lote del colorante y el agua
residual en estudio, obtenidos de una lavandería donde se manufacturan pantalones de
mezclilla en Almoloya del Río, Estado de México. El colorante fue caracterizado por
espectrofotometría de infrarrojo y UV-Vis, y al ser comparado con un estándar de
trisulfonato potásico de índigo se observó que ambos espectros son idénticos, por lo que
el colorante en estudio es de tipo indigoide con una banda máxima de absorción de 591
nm. La caracterización del agua residual mostró un bajo índice de biodegradabilidad
(0.25), indicando la presencia de materia orgánica no biodegradable, además se encontró
una alta concentración de fósforo (93.7 mg/L).
Las cinéticas de adsorción tanto de las soluciones acuosas del colorante como del agua
residual evaluando el carbono orgánico total (COT), demanda química de oxígeno (DQO)
y color se ajustaron al modelo de pseudo-segundo orden y de Elovich, indicando una
adsorción de tipo química. La arcilla natural (Mt-KSF) resultó ser la más eficiente en la
Perla Tatiana Almazán Sánchez XI
“Tratamientos avanzados para la remoción de un colorante de origen textil”
remoción del color en ambos sistemas con una capacidad de adsorción del colorante de
9.66 mg/g, mientras que para el color en el agua residual fue de 50 U PtCo/g; en las
cinéticas de adsorción de COT se observó una desorción sugiriendo una baja afinidad del
adsorbente con parte de la materia orgánica presente en el agua. Las capacidades de
adsorción al final del tratamiento fueron de 9.04 mg DQO/g, 36.47 U PtCo/g y 2.52 mg
COT/g para Mt-Fe-7, mientras que para el carbón activado natural (AC-N) fueron de 14.07
mg DQO/g, 40.32 U PtCo/g y 3.40 mg COT/g, siendo estos dos materiales los más
eficientes en el tratamiento del agua residual. El carbón modificado con cobre (AC-Cu-2)
fue muy eficiente en la remoción del colorante en solución acuosa pero no así para DQO,
color y COT del agua residual.
Las isotermas realizadas con las soluciones acuosas mostraron que la arcilla natural (Mt-
KSF), la modificada con hierro (Mt-Fe-7), el carbón natural (AC-N) y el carbón
modificado con cobre (AC-Cu-2) se ajustaron al modelo de Freundlich, con valores de
KF=14.28, 0.28, 1.63 y 1.84 ((mg/g)(L/mg)1/n), respectivamente; mientras que para la
arcilla modifica con cobre (Mt-Cu-7) los datos se ajustaron al modelo de Langmuir con
una qm de 2.62 mg/g. Para el color en el agua residual la KF fue de 0.52, 0.08, 0.41 y 0.32
((mg/g)(L/mg)1/n), con Mt-KSF, Mt-Fe-7, AC-N y AC-Cu-2, respectivamente.
Los ciclos de adsorción-regeneración evaluados con las soluciones acuosas del colorante
indicaron mejores eficiencias de remoción cuando los materiales se regeneraron con
peróxido de hidrógeno en presencia de luz solar, siendo el material más eficiente la arcilla
modificada con hierro con remociones superiores al 85% en los cuatro ciclos evaluados.
En los resultados obtenidos con el agua residual se observó un comportamiento diferente
cuando se evaluó la remoción de color, DQO y COT, pues las mejores eficiencias se
obtuvieron en ausencia de luz solar.
En un tercera etapa se evaluaron sistemas en continuo y las columnas de adsorción
indicaron que la arcilla modificada con hierro (Mt-Fe-7) presentó los mayores tiempos de
ruptura para color y TOC de 160 y 180 min respectivamente, con una concentración de
ruptura de 100 U PtCo de color y 15 mg/L de COT y capacidades de adsorción de 19 U
PtCo/g y 10 mg COT/g. Los modelos de Thomas y Yoon-Nelson mostraron un mejor ajuste
de los datos obtenidos con coeficientes de correlación mayores a 0.80.
Perla Tatiana Almazán Sánchez XII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
En la cuarta etapa se construyó un concentrador parabólico compuesto (CPC-2D) para
concentrar radiación UV proveniente del sol y aplicarlo en el proceso de foto-Fenton
heterogéneo, obteniéndose una radiación UV-A y UV-B concentrada de 54.29±0.71 y
1.65±0.37 W/m2 respectivamente. La arcilla modificada con hierro (Mt-Fe-7) y carbón
modificado con cobre (AC-Cu-2) fueron utilizados como agentes catalizadores para el
proceso de foto-Fenton así como peróxido de hidrógeno. Los resultados mostraron que
utilizando 1.5 g de catalizador, una concentración de H2O2 de 0.5 M y radiación UV, AC-
Cu-2 promovió la oxidación del colorante presente en solución acuosa en 2 h, mientras que
con la arcilla modificada con hierro se logró a las 3.5 h con eficiencias de remoción de 99
y 98% respectivamente. La eficiencia de remoción de color del agua residual textil fue 93
y 90% para AC-Cu-2 y Mt-Fe-7 respectivamente con 4 h de tratamiento.
Perla Tatiana Almazán Sánchez XIII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ABSTRACT
Perla Tatiana Almazán Sánchez XIV
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ABSTRACT
In this work, the remove a dye from aqueous solution and the treatment of textile
wastewater using natural and iron and copper modified materials and advanced oxidation
by Fenton and photo-Fenton heterogeneous processes are presented.
Clay and activated carbon were modified using Fe and Cu electrodes at pH values of 7 and
2 respectively. The materials were characterized by scanning electronic microscopy
(SEM), electron X-ray dispersive spectroscopy (EDS), X-ray diffraction and specific area
(BET), the optimum pH for clay modifications with Fe and Cu was 7, whereas for copper
modified activated carbon was 2, because de elemental analysis indicated that under the
above conditions the content of evaluated metals is highest. The specific area for natural
and iron and copper modified clay samples was 5.97, 131.30 and 78.44 m2/g, whereas for
natural and copper modified activated carbon at pH 2 was 654.85 and 647.61 m2/g.
Dye and wastewater used in this study were obtained from a laundry where jeans are
manufactured in Almoloya del Río in Mexico State. Dye was characterized by infrared
spectrophotometry and UV-Vis and it was compared with a standard of potassium indigo
trisulfonate and it was observed that both spectra were identical, whereby the dye used in
this study is an indigo dye with a maximum absorption band at 591 nm. The
characterization of wastewater shows a low biodegradability index (0.25) indicating the
presence of non-biodegradability organic matter, and a high concentration of phosphorous
was found (93.7 mg/L).
Adsorption kinetics for aqueous solutions of dye and textile wastewater evaluating total
organic carbon (TOC), chemical oxygen demand (COD) and color were best adjusted to
pseudo-second order and Elovich models indicating chemisorption processes. Natural clay
(Mt-KSF) was the most efficient material in the removal of color for both systems with a
dye adsorption capacity of 9.66 mg/g, whereas for color from wastewater was 50 UPtCo/g;
in adsorption kinetics of TOC a desorption process was observed suggesting a low affinity
between adsorbent and organic matter present in the wastewater. The adsorption capacities
at the end of treatment were 9.04 mg COD/g, 36.47 U PtCo/g and 2.52 mg TOC/g for Mt-
Fe-7, and for natural activated carbon (AC-N) were 14.07 mg COD/g, 40.32 U PtCo/g and
Perla Tatiana Almazán Sánchez XV
“Tratamientos avanzados para la remoción de un colorante de origen textil”
3.40 mg TOC/g, these materials were the most efficient in the treatment of wastewater.
Copper modified activated carbon (AC-Cu-2) was very efficient in the removal of dye
from aqueous solutions but it showed a different behavior in the removal of COD, color
and TOC from wastewater.
Adsorption isotherms of aqueous solutions of dye showed that natural clay (Mt-KSF), iron
modified clay (Mt-Fe-7), natural carbon (AC-N) and copper modified carbon (AC-Cu-2)
were best adjusted to Freundlich model with KF values of 14.28, 0.28, 1.63 and 1.84
((mg/g)(L/mg)1/n) respectively, whereas for copper modified clay the data were adjusted
to Langmuir isotherm with a qm of 2.62 mg/g. For color in textile wastewater KF values
were 0.52, 0.08, 0.41 and 0.32 ((mg/g)(L/mg)1/n) for Mt-KSF, Mt-Fe-7, AC-N and AC-
Cu-2, respectively.
Adsorption-regeneration cycles evaluated with aqueous solutions of dye showed the best
removal efficiencies when the materials were regenerated with hydrogen peroxide in
presence of sunlight, the most efficient material was iron modified clay with removal
percentages higher than 85% in the four cycles evaluated. The results obtained with
wastewater were different behavior the best efficiencies for the removal of color, COD and
TOC were obtained in absence of sunlight.
Fixed bed columns indicated that iron modified clay (Mt-Fe-7) shows the higher
breakthrough times for color and TOC of 160 and 180 min respectively, with a
breakthrough concentration of 100 U PtCo for color and 15 mg/L of TOC and adsorption
capacities of 19 UPtCo/g and 10 mg TOC/g. Data obtained was best adjusted to Thomas
and Yoon-Nelson models with correlation coefficients higher than 0.80.
A compound parabolic concentrator (CPC-2D) was built to concentrate UV radiation from
sunlight and applied in photo-Fenton heterogeneous process obtaining concentrated UV
A and UV-B radiation of 54.29±0.71 and 1.65±0.37 W/m2 respectively. Iron modified clay
(Mt-Fe-7) and copper modified activated carbon (AC-Cu-2) was used as catalyst in the
photo-Fenton process with hydrogen peroxide. The results show that using 1.5 g of
catalyst, a concentration of H2O2 of 0.5 M and UV radiation, AC-Cu-2 promoted the
oxidation of dye present in aqueous solutions in 2 h, whereas for Mt-Fe-7 the oxidation
Perla Tatiana Almazán Sánchez XVI
“Tratamientos avanzados para la remoción de un colorante de origen textil”
was achieved in 3.5 h with removal efficiencies of 99 and 98%. The removal efficiencies
for color from textile wastewater was of 93% and 90% for AC-Cu-2 and Mt-Fe-7
respectively in 4 h of treatment.
Perla Tatiana Almazán Sánchez XVII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ÍNDICE
RESUMEN ...................................................................................................................... XIABSTRACT.................................................................................................................... XVINTRODUCCIÓN ........................................................................................................ XXI1. ANTECEDENTES....................................................................................................... 1
1.1 Colorantes................................................................................................................. 21.2 Industria de la mezclilla en México y su problemática ambiental............................ 3
1.2.1 Normatividad mexicana correspondiente a la descarga de aguas residuales ..... 51.3 Tratamientos empleados para la remoción de colorantes de aguas residuales......... 7
1.3.1 Procesos de oxidación avanzada ....................................................................... 91.3.1.1 Proceso de Fenton homogéneo ................................................................... 91.3.1.2 Proceso foto-Fenton homogéneo .............................................................. 111.3.1.3 Proceso Fenton heterogéneo ..................................................................... 12
1.4 Adsorción ............................................................................................................... 131.4.1 Modelos cinéticos de adsorción en sistema batch ........................................... 15
1.4.1.1 Modelo de pseudo-primer orden............................................................... 151.4.1.2 Modelo de pseudo-segundo orden ............................................................ 151.4.1.3 Modelo de Elovich .................................................................................... 16
1.4.2 Isotermas de adsorción .................................................................................... 161.4.2.1 Ecuación de isoterma de Langmuir........................................................... 171.4.2.2 Ecuación de isoterma de Freundlich ......................................................... 17
1.4.3 Columnas de adsorción.................................................................................... 181.4.3.1 Modelos de adsorción en columna............................................................ 18
1.4.3.1.1 Modelo de Thomas ............................................................................. 181.4.3.1.2. Modelo de Bohart-Adams ................................................................. 19
1.5 Aplicación de la energía solar en el tratamiento de las aguas residuales ............... 211.5.1 Concentradores parabólicos compuestos ......................................................... 21
1.5.1.1 Concentrador en dos dimensiones (CPC-2D)........................................... 222. JUSTIFICACIÓN E HIPÓTESIS .............................................................................. 25
2.1 JUSTIFICACIÓN CONTEXTUAL Y CIENTÍFICA ........................................... 262.2. HIPÓTESIS ........................................................................................................... 27
3. OBJETIVOS .............................................................................................................. 283.1 Objetivo general...................................................................................................... 293.2 Objetivos específicos ............................................................................................. 29
4. METODOLOGÍA ...................................................................................................... 304.1 Diagrama de bloques.............................................................................................. 314.2 Selección de los adsorbentes .................................................................................. 314.3 Modificación electroquímica de materiales ........................................................... 314.4 Caracterización del material adsorbente ................................................................ 33
4.4.1 Microscopía Electrónica de Barrido (MEB) y Microanálisis elemental por espectroscopia de rayos X de energía dispersa (EDS) .................................... 33
4.4.2 Difracción de Rayos X..................................................................................... 344.4.3 Análisis de BET .............................................................................................. 34
Perla Tatiana Almazán Sánchez XVIII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4.4.4 Determinación del punto cero de carga ........................................................... 344.4.5 Determinación de hierro y cobre ..................................................................... 34
4.5 Preparación de soluciones acuosas del colorante .................................................. 354.5.1 Caracterización del colorante .......................................................................... 35
4.6 Muestreo del efluente textil .................................................................................... 354.7 Caracterización fisicoquímica del efluente textil de acabado de prendas de
mezclilla ................................................................................................................. 354.8 Pruebas de sorción evaluando el efecto del pH en soluciones acuosas del
colorante ................................................................................................................. 364.9 Cinéticas de adsorción ........................................................................................... 37
4.9.1 Solución acuosa del colorante ......................................................................... 374.9.2 Agua residual .................................................................................................. 37
4.10 Isotermas de adsorción ......................................................................................... 384.10.1 Soluciones acuosas del colorante .................................................................. 384.10.2 Agua residual ................................................................................................ 38
4.11 Ciclos de adsorción-regeneración ........................................................................ 394.12 Columnas de adsorción ........................................................................................ 404.13 Proceso de foto-Fenton heterogéneo solar ........................................................... 40
4.13.1 Construcción de concentrador solar CPC-2D ............................................... 404.13.2 Proceso de Fenton y foto-Fenton heterogéneo............................................... 41
5. RESULTADOS.......................................................................................................... 425.1. Primer artículo de investigación ............................................................................ 435.2 Segundo artículo de investigación ......................................................................... 585.3 Tercer artículo de investigación.............................................................................. 73
5.3.1 Carta de envío ................................................................................................. 735.3.2 Manuscrito ....................................................................................................... 74
6. DISCUSIÓN DE RESULTADOS ............................................................................1007. CONCLUSIONES ....................................................................................................1088. SUGERENCIAS .......................................................................................................1129. PRODUCTOS ...........................................................................................................114
9.1 Listado de productos obtenidos .............................................................................1159.2 Documentos probatorios .......................................................................................119
10. ANEXOS ................................................................................................................ 14410.1 ANEXO 1 ............................................................................................................14510.2 ANEXO 2 ............................................................................................................149
11. REFERENCIAS ......................................................................................................152
Perla Tatiana Almazán Sánchez XIX
“Tratamientos avanzados para la remoción de un colorante de origen textil”
LISTA DE FIGURAS
Fig. 1 Grupos funcionales de colorantes usados en la industria textil ............................... 2Fig. 2 Canal de descarga del efluente de una lavandería de acabados de prendas de
mezclilla ................................................................................................................... 4Fig. 3 Estructura química del colorante azul índigo ......................................................... 4Fig. 4 Esquema del proceso de Fenton homogéneo ........................................................ 11Fig. 5 Esquema del proceso de Fenton heterogéneo ....................................................... 13Fig. 6 Aspecto físico del CPC-2D (a) y ángulo de aceptación del CPC (b) .................... 22Fig. 7 Diagrama de bloques de la metodología ............................................................... 31Fig. 8 Celda electroquímica para la modificación de los materiales adsorbente ............. 33Fig. A1- 1 Esquema del CPC para tratamiento de aguas residuales ...............................146Fig. A1- 2 Parábolas obtenidas a partir de los datos calculados para dar perfil
parabólico al CPC-2D............................................................................................. 148Fig. A2- 1 Tiempo de ruptura vs altura de lecho de la columna usando Mt-KSF ..........149Fig. A2- 2 Tiempo de ruptura vs altura de lecho de la columna usando Mt-Fe-7 ..........150Fig. A2- 3 Tiempo de ruptura vs altura de lecho de la columna usando AC-N ............. 150
LISTA DE TABLAS
Tabla 1 Límites máximos permisibles para descarga de aguas residuales a cuerpos deagua, alcantarillado y reuso de agua tratada.......................................................... 6
Tabla 2 Diversos tratamientos empleados en la remoción de azul índigo e índigocarmín..................................................................................................................... 7
Tabla 3 Tiempo requerido para la modificación de la arcilla y el carbón activado ........ 32Tabla 4 Parámetros fisicoquímicos para análisis de agua residual .................................. 36Tabla 5 Materiales utilizados en las pruebas de adsorción a diferentes valores de pH.... 37Tabla A1- 1 Datos obtenidos a partir de la ecuación de la parábola..............................147Tabla A2- 1 Constantes de Bohart-Adams ..................................................................... 151
Perla Tatiana Almazán Sánchez XX
“Tratamientos avanzados para la remoción de un colorante de origen textil”
INTRODUCCIÓN
Perla Tatiana Almazán Sánchez XXI
“Tratamientos avanzados para la remoción de un colorante de origen textil”
INTRODUCCIÓN
La industria textil representa un papel importante en la economía mundial, donde
el teñido es una de las etapas más representativas durante el proceso de fibras textiles.
Actualmente, existe el inconveniente de la descarga de efluentes de la industria textil a
cuerpos de agua naturales causa alteraciones en la actividad biológica acuática (Amin,
2009), ya que los colorantes usados pueden ser mutagénicos y carcinogénicos (Kadirvelu
et al., 2003).
México es uno de los grandes productores de mezclilla en el mundo y proveedor
importante para el mercado de los Estados Unidos (MANUFACTURA, 2013); así que,
siendo un país en desarrollo, susceptible a los efectos del cambio climático, con muchas
desigualdades y con regulaciones y cumplimiento inadecuados, los recursos de agua son
particularmente vulnerables (Greenpeace, 2012), propiciando así su contaminación.
El Estado de México presenta el mayor número de establecimientos de acabados
textiles a nivel nacional (INEGI, 2009). Almoloya del Rio, municipio mexiquense, donde
la principal actividad económica es la manufactura de pantalón de mezclilla, ha traído
como consecuencia la afectación de cuerpos de agua por la descarga de sus efluentes
residuales sin un tratamiento previo.
Uno de los colorantes utilizados en la tinción de la mezclilla es el azul índigo, por
lo que su presencia en efluentes textiles es notable, además de que sus productos de
biodegradación son desconocidos (Gutiérrez-Segura et al., 2012). Usualmente, los
colorantes en agua son transformados en aminas aromáticas toxicas (Wong y Yu, 1999),
provocan la absorción y reflexión de la luz solar, impiden la fotosíntesis en plantas
acuáticas (Bouasla et al., 2010) y presentan propiedades recalcitrantes (Cañizares et al.,
2006, Mesquita et al., 2012).
Por tal motivo, diversos tratamientos se han enfocado en la remoción del azul
índigo, como los procesos biológicos (Khelifi et al., 2008), coagulación-floculación
(Albuquerque et al., 2013), electroquímicos (Sanromán et al., 2004), Fenton y foto-Fenton
(Vedrenne et al., 2012) y adsorción (Gutiérrez-Segura et al., 2012).
Perla Tatiana Almazán Sánchez XXII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
La adsorción es un tratamiento aplicado para la remoción de colorantes y
contaminantes orgánicos en aguas residuales (Metcalf y Eddy; 2003); el adsorbente más
utilizado es el carbón activado por su gran área superficial, estructura y volumen de poro
y capacidad de adsorción (Kurniawan y Lo, 2009, El-Naas et al., 2010), a pesar de las
desventajas de su precio alto y baja regeneración (Weng y Hsu, 2008). Actualmente, es de
suma importancia desarrollar adsorbentes de bajo costo y fácilmente disponibles (Karadag
et al., 2007), capaces de ser regenerados y reutilizados.
Por otro lado, el proceso de Fenton homogéneo, es usado para la oxidación de
materia orgánica mediante la formación de radicales hidroxilo a partir de peróxido de
hidrógeno catalizado por sales de Fe2+ en medio acuoso a valores de pH de 2.8; una
limitante al final del tratamiento es la formación de una gran cantidad de lodos (hidróxidos
de hierro) (Chen et al., 2009). Una alternativa al proceso de Fenton homogéneo es la
aplicación del proceso Fenton heterogéneo. Donde se utilizan catalizadores sólidos, donde
iones de Fe2+ y Fe3+, son soportados en materiales como zeolitas o arcillas (Herney-
Ramirez et al., 2010), para efectuar la producción de radicales hidroxilo y se evite la
formación de lodos, promoviendo así la regeneración del material (Kusic et al., 2006). En
el proceso de foto-Fenton se utiliza radición UV para generar radicales hidroxilo, la
principal fuente de esta radiación son lámparas que pueden tener tiempos de vida media
cortos y contienen mercurio (Mbonimpa et al., 2012); sin embargo, otra fuente de radiación
UV es la energía solar, una alternativa que permite aplicar procesos más sustentables. Los
concentradores parabólicos compuestos, son dispositivos que permiten concentrar
radiación solar y que recientemente han sido aplicados en el tratamiento de aguas
residuales como la fotocatálisis y la desinfección (Mbonimpa et al., 2012, Salgado-
Tránsito et al., 2015, Velegraki y Mantzavinos, 2015).
Es por ello que en este trabajo se efectuó la modificación electroquímica de una
arcilla y un carbón activado con electrodos de hierro y cobre, para aplicar los tratamientos
avanzados de adsorción, Fenton y foto-Fenton heterogéneo, en la eliminación de un
colorante textil en solución acuosa utilizado en el acabado de prendas de mezclilla.
En el capítulo 1 se muestra la información correspondiente a la problemática de
existe por las descargas de efluentes de la industria textil a cuerpos de agua superficial, los
Perla Tatiana Almazán Sánchez XXIII
“Tratamientos avanzados para la remoción de un colorante de origen textil”
diferentes tratamientos aplicados para remover colorantes del agua, así como la
descripción de los procesos de oxidación como Fenton y los procesos de adsorción; en
tanto que los capítulos 2 y 3 se encuentran la justificación científica y contextual del
trabajo, así como la hipótesis y los objetivos propuestos, mientras que en el capítulo 4 se
describe la metodología realizada durante el trabajo de investigación. En el capítulo 5 se
presentan los resultados obtenidos en tres artículos científicos, en el primero se muestra el
tratamiento de adsorción evaluado con soluciones acuosas del colorante trisulfonato
potásico de índigo, mientras que en el segundo se encuentra el proceso de adsorción en
batch y columna de un agua residual proveniente de una lavandería donde se manufacturan
prendas de mezclilla y finalmente en el tercer artículo se muestra el proceso de foto-Fenton
heterogéneo aplicado en soluciones acuosas del colorante y en el agua residual textil. En
el capítulo 6 se indica una discusión general del trabajo realizado, en el capítulo 8 se
muestran las conclusiones, en el capítulo 9 las sugerencias y en el 10 los productos
obtenidos.
Perla Tatiana Almazán Sánchez XXIV
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1. ANTECEDENTES
Perla Tatiana Almazán Sánchez 1
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ANTECEDENTES
1.1 Colorantes
Los colorantes son compuestos orgánicos cuyas estructuras están constituidas por
dos componentes, los cromóforos que son grupos funcionales no saturados como los
dobles y triples enlaces que absorben energía en las regiones del espectro visible (Skoog
et al., 2005) y que son responsables del color, el otro componente son los auxocromos los
cuales son un complemento del grupo cromóforo haciendo más soluble la molécula del
colorante y dándole más afinidad con las fibras donde se aplican (Gupta, et al., 2009). Los
principales grupos cromóforos presentes en colorantes usados en la industria textil son los
azo e indólicos (Fig. 1), mientras que los grupos auxocromos pueden ser grupos carbonilo,
hidróxido, sulfonato y aminas.
Se estima que alrededor de 700,000 toneladas de colorantes textiles sintéticos son
producidas anualmente, además son diseñados para ser químicamente estables, resistentes
a la degradación y con propiedades de fijación en las telas (Asghar et-al., 2015). Sin
embargo aproximadamente 280,000 toneladas de estos colorantes utilizados son
descargadas al ambiente, siendo de gran preocupación ya que son considerados un tipo de
contaminante por ser tóxicos para seres humanos por ingestión oral e inhalación, además
de causar irritación en piel y ojos (Gupta et-al., 2009), pueden ocasionar afectaciones en
el sistema reproductor, los riñones, hígado, cerebro y en el sistema nervioso central
(Yagub et al., 2014). Los colorantes al estar presentes en el agua de ríos, lagos o mares
provocan la absorción y reflexión de la luz solar impidiendo la fotosíntesis de plantas
acuáticas (Bouasla et al., 2010), pueden ser transformados en aminas aromáticas tóxicas,
Perla Tatiana Almazán Sánchez 2
“Tratamientos avanzados para la remoción de un colorante de origen textil”
exhiben propiedades recalcitrantes (Cañizares et al., 2006, Mesquita et al., 2012),
mutagénicas y carcinogénicas (Kadirvelu et al., 2003), impidiendo los procesos
metabólicos biológicos de plantas y animales y por lo tanto ocasionando la destrucción de
comunidades acuáticas. Es por ello que su presencia en el ambiente debe ser minimizada
o restringida.
1.2 Industria de la mezclilla en México y su problemática ambiental
En los últimos 55 años, la disponibilidad de agua por habitante se ha reducido
significativamente, de 11 500 m3 en 1955 a 4 263 m3 en el 2010. La contaminación del
agua dulce, por efluentes municipales e industriales, es evidente en todo México, desde las
cuencas Lerma-Chapala-Santiago, Balsas, Valle de México y Papaloapan (CONAGUA,
2011).
La industria del vestido y los textiles constituye la cuarta actividad de fabricación
más grande en México y es vital para su economía. El sector es uno de los más importantes
en términos de empleo, con más de 500,000. México es el cuarto proveedor de textiles y
prendas más grande para el mercado de los EE.UU (México Today, 2011;
MANUFACTURA, 2013).
De acuerdo con el censo económico del año 2009 realizado por el Instituto Nacional
de Estadística y Geografía (INEGI), el valor de la producción en la fabricación e insumos
textiles y acabados de mezclilla en México es de $ 4 775 096 M.N., siendo el sector que
más ganancias económicas presenta. Por otro lado, el Estado de México, es el estado con
mayor número de unidades económicas dedicadas a la fabricación de insumos, acabados
textiles y prendas de vestir, con un 11.4 % del total del país, colocándolo así como uno de
los principales estados manufactureros. El municipio mexiquense de Almoloya del Río,
cuenta con 399 unidades económicas registradas dedicadas a la fabricación de prendas de
vestir, siendo una de las actividades económicas más importantes, entre ellas la
manufactura de pantalón de mezclilla.
Sin embargo, el desarrollo de esta actividad, ha ocasionado la contaminación de
agua por la descarga de aguas residuales sin un tratamiento previo a alcantarillados o
Perla Tatiana Almazán Sánchez 3
“Tratamientos avanzados para la remoción de un colorante de origen textil”
cuerpos de agua superficial (Butrón et al., 2007), pues la industria textil aproximadamente
de 21 a 377 m3 de agua son consumidos por tonelada de producto textil en términos de
volumen gastado, así como la presencia de color y composición química del agua residual
(materia orgánica e inorgánica) (Asghar et-al., 2015).
En la Fig. 2, se muestra la imagen de un efluente proveniente de una lavandería de
acabados de prendas de mezclilla en Almoloya del Río, que se descarga a un canal de
desagüe a cielo abierto.
Fig. 2 Canal de descarga del efluente de una lavandería de acabados de prendas de mezclilla
El efluente (Fig. 2) tiene una coloración azul, atribuida al azul índigo, uno de los
colorantes más utilizados en el teñido de la mezclilla; contiene en su estructura química
cetonas cíclicas que limitan su solubilidad en agua. La forma soluble (Fig. 3) (Macy, 2005)
se obtiene utilizando agentes reductores como hidroxiacetona, hidrógeno, métodos
electroquímicos o con ditionito de sodio (Na2S2Ü4) (Bozic y Kokol, 2008); siendo este
último el más usado (Zollinger, 2003).
Fig. 3 Estructura química del colorante azul índigo
Perla Tatiana Almazán Sánchez 4
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1.2.1 Normatividad mexicana correspondiente a la descarga de aguas residuales
En México existen tres principales normas que regulan la descarga de aguas
residuales y el reuso de aguas residuales tratadas, las cuales se mencionan a continuación:
• La NOM-001-SEMARNAT-1996 establece los límites máximos permisibles de
contaminantes en las descargas de aguas residuales en aguas y bienes nacionales
como ríos, embalses naturales o artificiales y aguas costeras.
• La NOM-002-SEMARNAT-1996 establece los límites máximos permisibles de
contaminantes en las descargas de aguas residuales a los sistemas de alcantarillado
urbano y municipal,
• La NOM-003-SEMARNAT-1997 establece los límites máximos permisibles de
contaminantes para las aguas residuales tratadas que se reusen en servicios al
público.
La Tabla 1 enlista los principales parámetros que son regulados por dichas normas
y que deben de cumplir los diferentes sectores económicos e industriales que descargan
sus aguas residuales a cuerpos de agua o alcantarillados.
Por otro lado, la NOM-CCA-014-ECOL/1993, establece los límites máximos
permisibles de contaminantes en las descargas de aguas residuales provenientes de la
industria textil a cuerpos receptores (redes colectoras, ríos, cuencas, vasos, aguas marinas),
la cual considera un valor promedio diario de pH de 6-9, de la demanda bioquímica de
oxígeno (DBO5) de 100 mg/L, de la demanda química de oxígeno (DQO) de 200 mg/L, de
solidos suspendidos totales y sólidos sedimentables de 100 mg/L y 1.0 mL/L
respectivamente, de grasas y aceites de 20 mg/L, de cromo total de 1.0 mg/L, de sulfuros
de 0.2 mg/L, fenoles de 0.1 mg/L, de coliformes totales de 1000 NMP/100 mL. Además si
hay descargas que aunque cumplan con la norma ocasionen efectos adversos a un cuerpo
de agua, se pueden fijar otros parámetros con los cuales deba cumplir, como color, cobre,
Perla Tatiana Almazán Sánchez 5
“Tratamientos avanzados para la remoción de un colorante de origen textil”
fósforo total, sólidos disueltos totales, temperatura, tóxicos orgánicos (organoclorados,
policíclicos aromáticos) y unidades de toxicidad aguda con Daphnia marga. Esta norma a
diferencias de las NOM-001-SEMARNAT-1996, NOM-002-SEMARNAT-1996 y NOM-
003-SEMARNAT-1997 incluye a la demanda química de oxígeno como parámetro a
cumplir en la descarga de aguas textiles. De acuerdo con Metcalf y Eddy (2003), el índice
de biodegradabilidad (r) relaciona el valor de la Demanda Química de Oxígeno y la
Demanda Bioquímica de Oxígeno (r=DBO5/DQO), cuando este valor es menor a 0.3 indica
que la materia orgánica presente en un agua residual tiene una baja biodegradabilidad y
que puede ser tóxica. Los valores de DQO y DBO5 que se encuentran en las aguas
residuales textiles son de 150-2500 mg/L y de 100-4000 mg/L respectivamente (Asghar,
et-al., 2015)
Tabla 1 Límites máximos permisibles para descarga de aguas residuales a cuerpos de agua, alcantarillado y reuso de agua tratada
Parámetro NOM-001 NOM-002 NOM-003pH 5.0-10.0 5.5-10.0 N.A.Temperatura (°C) N.A., 40 40 N.A.Grasas y Aceites (mg/L) 15 50 15Materia flotante Ausente Ausente AusenteSólidos Sedimentables (mL/L) 1 5.0 N.A.Solidos Suspendidos Totales mg/L 40-200 40-200 N.A.Demanda Bioquímica de Oxígeno ( mg/L) 30-200 30-200 20-30Nitrógeno Total(mg/L) N.A., 15-40 N.A. 20-30Fósforo Total (mg/L) 5-20 N.A. N.A.Arsénico Total (mg/L) 0.1-0.2 0.50 0.2-0.4Cadmio Total (mg/L) 0.1-0.2 0.50 0.2-0.4Cobre Total (mg/L) 4.0 10 4.0-6.0Cromo Total (mg/L) 0.5-1.0 0.50** 1.0-1.5Mercurio Total (mg/L) 0.005-0.020 0.01 0.01-0.02Níquel Total (mg/L) 2.0 4.0 2.0-4.0Plomo Total (mg/L) 0.2-0.5 1.0 0.5-1.0Zinc Total (mg/L) 10 6.0 10-20Cianuro Total (mg/L) 1.0-2.0 1.0 2.0-3.0Coliformes fecales (NMP*/100 mL) 1000-2000 N.A 240 y 1000Huevos de Helminto (huevo/L) 1- 5 N.A < 1 y 5
N.A.: No aplica; *NMP: Número más probable; ** Hexavalente
Perla Tatiana Almazán Sánchez 6
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1.3 Tratamientos empleados para la remoción de colorantes de aguas residuales
Diversos tratamientos han sido aplicados para la remoción de colorantes de las
aguas residuales, entre ellos la degradación fotocatalítica (Sohrabi y Ghavami, 2008);
(Sleiman et al., 2007), degradación sonoquímica (Abbasi y Asl, et al., 2008), membranas
de intercambio iónico (Wu et al., 2008), degradación electroquímica (Fan et al., 2008),
procesos de adsorción/precipitación (Zhu et al., 2007), degradación químico-biológica
(Sudarjanto et al., 2006), foto-Fenton solar (Sarria et al., 2003), adsorción (Wu et al.,
2008), coagulación/floculación (Tan et al., 2000), tratamientos electroquímicos,
ultrafiltración (Zaghbani, et al., 2008), incineración electroquímica, nanofiltración,
osmosis inversa (Amar et al., 2009), etc.
Los tratamientos mencionados anteriormente, son conocidos como tratamientos
avanzados o terciarios y se definen como un tratamiento adicional necesario para remover
constituyentes suspendidos, coloidales y disueltos, después de un tratamiento secundario
convencional (Melcalf y Eddy, 2003).
En la tabla 2, se enlistan algunos de los tratamientos empleados para la remoción
de azul índigo e índigo carmín en solución acuosa, usados en el teñido de la mezclilla.
Tabla 2 Diversos tratamientos empleados en la remoción de azul índigo e índigo carmín.
Autores Características % Remoción o qe
Ads
orci
ón
(Zainal et
al., 2005)
Colorante: Índigo carmín, C0=10.4 mg/L, TiO2 depositado
en laminillas de vidrio, lámparas fluorescentes y aire.92.4%
(Lakshmi et
al., 2009)
Colorante: Índigo carmín, C0=50 mg/L, Cenizas de cáscara
de arroz, pH 5.4, t=8 h.97%
(Othman et
al., 2006)
Colorante: Índigo carmín, C0=100 mg/L, Zeolita ZSM-5,
Mn/ZSM-5), Mn-La/ZSM-5, pH=2, luz UV.100%
(Gutiérrez-
Segura et al.,
2012)
Colorante: Índigo carmín, C0=200 mg/L, zeolita modificada
con FeCl3 y material carbonoso obtenidos de la pirólisis de
lodos activados, pH 6.5.
qe (Fe-Ze)= 92.83 mg/g;
qe (MC)= 32.83 mg/g
Perla Tatiana Almazán Sánchez 7
“Tratamientos avanzados para la remoción de un colorante de origen textil”
(Shen et al.,
2009)
Colorante: Índigo carmín, C0=40 mg/L, Bentonita
modificada con polidialildimetilamonio (PDADMA-
bentonita), dosis: 3 g/L, pH= 5.
97%C
oagu
laci
ón/
flocu
laci
ón (Albuquerqu
e et al.,
2013)
Colorante: Azul Índigo, agua residual del proceso de
producción de NaCl y con solución de MgCl2 (100 mg
Mg2+/L). 150 rpm en 3 min y 48 rpm por 10 min, 30 min de
asentamiento
80, 70 %
respectivamente
Foto
-
Fent
on (Vedrenne et
al., 2012)
Colorante: Azul Índigo, C0=33.3 mg/L, Oxalato ferroso
(C2O42-/Fe2+= 35.), 1280 mg/L H2O2, pH= 5-673 %
Ele
ctro
quím
icos
(Cameselle
et al., 2005)
Colorante: Azul Índigo, C0=200 mg/L, Electrodos de
grafito, E.S: KBr, 5 V, pH 7, 100 mL.98%, 30 min
(Sanromán
et al., 2004)
Colorante: Azul Índigo, G)=100 mg/L, Electrodos de Pt, 5
V, pH 4.5.90%, 60 min.
(Secula et
al., 2011)
Colorante: Índigo carmín, C0=40 mg/L,
Electrocoagulación, electrodos de acero inoxidable, pH=7,
DC=54.57 A/m2, E.S.= 1.5 g/L NaCl
99.9 %
(Guaraldo et
al., 2013)
Colorante: Índigo carmín, C0=23 mg/L,, Foto-ánodo de
Ti/TiO2/WO3, 0.1 M Na2SO4, lámpara de luz visible, pH 2,
1 V.
97%, 120 min
(Butrón et
al., 2007)
Colorante: Azul Índigo, C0=536 mg/L, electrodos de DDB,
pH 6.3, 0.8<E<3V100
Bio
lógi
co
(Khelifi et
al., 2008)
Colorante: Azul Índigo, Aerobio, Reactor de tanque agitado
continuo (Q0= 1L); 3 bioreactores (Q0= 1L) de película fija,
TRH= 4 días, pH= 7.5
97.3%
(Manu y
Chaudhari,
2003)
Colorante: Azul Índigo, C0=100 mg/L, Reactor
semicontinuo anaerobio, TRH= 5 días, pH=6.5-7.3,85-90%
(Balan y
Monteiro,
2001)
Colorante: Azul Índigo, Uso de 4 hongos: Phellinusgilus,
Ph. chrysosporium, Pycnoporussanguineus y
Pleurotussajor-caju.
100, 75, 91, 94%,
respectivamente
Co: concetración inical; E.S: Electrolito soporte, THR: Tiempo de retención hidráulica, Qo=Influente, qe: capacidad de adsorción
Perla Tatiana Almazán Sánchez 8
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1.3.1 Procesos de oxidación avanzada
Los procesos convencionales usados para el tratamiento de aguas residuales, en
ocasiones son poco eficientes para destruir contaminantes orgánicos recalcitrantes y
tóxicos. Existe una gran cantidad de compuestos orgánicos persistentes que son de gran
interés debido a su alta concentración en medios acuáticos (Oturan y Brillas, 2007).
En los últimos años, métodos como Fenton, foto-Fenton, ozonación, oxidación
electroquímica y fotocatálisis han sido desarrollados exitosamente para remover
compuestos orgánicos persistentes (Oliveros et al., 1997). Estos métodos son llamados
procesos de oxidación avanzada (POAs) y se basan en el uso de agentes oxidantes fuertes
como el radical hidroxilo (•OH) con un potencial de oxidación E° (•OH/H2O) de 2.8 V,
que es generado in situ en el medio de reacción (Legrini et al., 1993). Estos procesos son
aplicados cuando las técnicas de oxidación convencionales son insuficientes por razones
cinéticas o debido a que los contaminantes son refractarios (Oturan y Brillas, 2007).
1.3.1.1 Proceso de Fenton homogéneo
El proceso Fenton es atractivo para la degradación de colorantes debido a que los
reactivos empleados son económicos y de baja toxicidad. Este proceso involucra la
formación del radical hidróxilo a partir de peróxido de hidrógeno (H2O2) catalizado con
sales de Fe2+.En presencia de compuestos orgánicos, como los colorantes, el radical
hidroxilo puede atacarlos por cuatro rutas: adición de radical, abstracción de hidrógeno,
transferencia de electrones y combinación de radicales, para finalmente promover su
mineralización (CO2, H2O, sales) (Deng y Englehardt, 2006). El uso del proceso Fenton
en fase homogénea presentan desventajas al final del tratamiento, por la alta concentración
de lodos (hidróxidos de hierro), que tiene un costo extra en mano de obra, reactivos y
tiempo al final del tratamiento (Chen et al., 2009). Las principales reacciones del proceso
Fenton son las reacciones mostradas en las ecuaciones 1-3 (Nam et al., 2001, Hsueh et al.,
2005, Sun et al., 2007):
Perla Tatiana Almazán Sánchez 9
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fe2+ + H2O2 + H+ > Fe3+ + «OH + H2O (1)
Fe3+ + H2O2 > Fe2+ + «OOH + H+ (2)
Fe3++«OOH > Fe2+ + O2 + H+ (3)
Existen algunas variantes del proceso Fenton, como el Fenton-like, que consiste en
el uso de iones Fe3+ para la generación de radicales hidro-peroxilos (•HO2) (Fu et al., 2009,
Malik y Saha, 2003), con un potencial de oxidación de 1.70 V (Ec. 4) (Legrini et al., 1993):
Fe3+ + II2O2 > Fe2+ + H+ + «HO2 (4)
La Ec. 4 es mucho más lenta que la Ec. 1, pero muestra como el Fe3+ puede ser
regenerado a Fe2+ y ser reutilizado en el proceso de Fenton.
Otra variante es el uso de cobre como agente catalizador en la reacción de Fenton;
Brillas et al., (2004) y Sirés et al., (2006), estudiaron los efectos del Cu2+ como co-
catalizador en el proceso de electro-Fenton para la remoción de compuestos orgánicos. El
sistema Cu2+/Cu+ involucra la reducción de Cu2+ a Cu+ con radicales hidro-peroxilos
(•HO2) y/o con radicales orgánicos R' (Ec. 5-6):
Cu2+ + HO2«> Cu+ + H+ + O2(g) (5)
Cu2+ + R'> Cu+ + H+ + O2(g) (6)
El Cu2+ puede ser regenerado por la oxidación de Cu+ con H2O2 como la reacción
de Fenton-Like (Ec. 7):
Cu+ + H2O2> Cu2+ + 'OH + —OH (7)
Perla Tatiana Almazán Sánchez 10
“Tratamientos avanzados para la remoción de un colorante de origen textil”
En la Fig. 4 se muestra un esquema general del proceso de Fenton homogéneo.
Fenton-Like ■*-__
Radical liidro- peroxilo
Agitaciónconstante
Fig. 4 Esquema del proceso de Fenton homogéneo
Lodos de hiilróxiilo de
hierro
1.3.1.2 Proceso foto-Fenton homogéneo
El proceso de foto-Fenton consiste en la combinación del reactivo Fenton
(Fe2+/H2O2) y radiación electromagnética (luz). En este proceso se lleva a cabo la
formación de radicales hidroxilo y la regeneración de Fe2+ por la foto-reducción de Fe3+
(Ec.8-9) (Herney-Ramírez, et al., 2010; Pignatelo, et. al., 1992).
Fe2+ + II2O2 > Fe(OH)2+ + *OH (8)
Fe(OH)2+ +hv> Fe2+ +«OH (9)
Perla Tatiana Almazán Sánchez 11
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Este proceso puede utilizar radiaciones UV-A (X = 315-400), UV-B (X = 285-315)
y UV-66352C (X < 285) como fUente de energía (Oller et al., 2007). La desventaja que
presenta este proceso son los costos excesivos por usar luz artificial, sin embargo, una
alternativa es el uso de la luz solar (X > 300) como fuente de energía renovable y disponible,
tomando ahora el nombre de foto-Fenton solar (Muñoz et al. 2008: 273).
1.3.1.3 Proceso Fenton heterogéneo
El proceso Fenton aplicando sales de hierro como catalizador ofrece costos
efectivos en la generación de radicales hidroxilo (Aleksic et al., 2010); pero sus eficiencias
se ven limitadas por la alta concentración de iones de hierro, además, el ciclo catalítico del
proceso Fenton es limitado por la formación de complejos de Fe3+ muy estables (Tarr,
2003; Bigda, 1995). Asimismo, el proceso se efectúa a valores de pH ácidos, lo que
requiere un fuerte acondicionamiento antes y después del tratamiento (Aleksic et al.,
2010).
Debido a esto, diversas investigaciones se han enfocado en desarrollar
catalizadores heterogéneos de hierro capaces de regenerarse (DíazGómez-Treviño et al.,
Gutiérrez-Segura et al., 2009, Kusic et al., 2006) para disminuir la formación de lodos, una
limitante en el proceso de Fenton homogéneo. Algunos catalizadores son mezclas de
óxidos de hierro y silica, zeolitas naturales o modificadas (Fajerwerg y Debellefontaine,
1996; Catrinescu et al., 2003), resinas (Aleksic, et al., 2010), arcillas pilareadas con hierro
(Ramirez et al., 2007), entre otros.
Algunos autores han desarrollado catalizadores para efectuar el proceso de foto-
Fenton heterogéneo en solución acuosa; por ejemplo, Banic et al., (2011) obtuvieron un
catalizador de Fe soportado en oxido de titanio (TiO2) para la remoción de un herbicida;
(Catrinescu et al., 2012) emplearon una arcilla pilareada con Fe y Al para remover 4-
clorofenol; mientras que Chen et al., (2009) usaron la arcilla montmorillonita para remover
el colorante naranja brillante X-GN.
Perla Tatiana Almazán Sánchez 12
“Tratamientos avanzados para la remoción de un colorante de origen textil”
En la Fig. 5 se muestra un esquema general del proceso de Fenton heterogéneo.
Fig. 5 Esquema del proceso de Fenton heterogéneo
1.4 Adsorción
La adsorción es uno de los procesos más utilizados para remover materia orgánica
e inorgánica de las aguas residuales. Es un proceso de trasferencia de masa que consiste
en un adsorbato o contaminante que se encuentra en una fase líquida o gaseosa y que es
Perla Tatiana Almazán Sánchez 13
“Tratamientos avanzados para la remoción de un colorante de origen textil”
adsorbido a una fase sólida o adsorbente (Metcalf y Eddy, 2003)(Ahmad y Hameed, 2009).
Existen diferentes adsorbentes que han sido usados para este proceso como el carbón
activado que ha sido ampliamente utilizado debido a su gran área superficial, su estructura,
volumen de poro y capacidad de adsorción (Kurniawan y Lo, 2009, El-Naas et al., 2010);
algunos aluminosilicatos como zeolitas y arcillas han sido usados también, algunos
biosorbentes y materias primas de la industria y la agricultura (Wan Ngah et al., 2011)
entre otros; la importancia de utilizar estos materiales es su disponibilidad, que sean
económicos y que puedan ser reutilizables (Karadag et al., 2007), para ello en ocasiones
estos materiales son modificados para poder mejorar sus capacidades de adsorción y
promover su regeneración para reusarlos en varios ciclos. Algunos procesos de
modificación son los tratamientos ácido/base, con surfactantes, intercambio iónico con
sales de hierro y recientemente la modificación electroquímica.
Algunos materiales que han sido modificados son el carbón activado. Liu y
colaboradores (2010) realizaron la modificación con cloruro férrico para la remoción de
cromo hexavalente; la impregnación de Fe en el carbón aumentó el área superficial del
adsorbente y mejoró la adsorción de Cr(VI). Por otro lado, Zabneva y colaboradores (2012)
lo modificaron con sulfato ferroso para adsorber 2, 4-dinitrofenol y 2-nitrofenol. Las
zeolitas han sido ampliamente estudiadas y aplicadas en procesos de adsorción debido a
su alta capacidad de intercambio iónico, alta área específica y su bajo costo, se han usado
en la remoción de metales pesados, amonio, fenoles, plaguicidas y colorantes (Crini, 2006,
Wang y Peng, 2010), y han sido modificadas por procesos de intercambio iónico
empleando sales de Fe3+ (Gutiérrez-Segura et al., 2009, Kusic et al., 2006) para remover
colorantes. Teutli y colaboradores (2013) aplicaron la modificación electroquímica con
electrodos de aluminio para remover iones fluoruros en solución acuosa. Por otro lado, las
arcillas también han sido modificadas por intercambio iónico o por pilearización mediante
la incorporación de hierro (Herney-Ramirez et al., 2010).
La modificación de los materiales con metales de transición como hierro y cobre
pueden ser aplicados no sólo en la adsorción sino también en procesos donde actúen como
agente catalizadores, tal es el caso del proceso de Fenton heterogéneo.
Perla Tatiana Almazán Sánchez 14
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1.4.1 Modelos cinéticos de adsorción en sistema batch
Las cinéticas de adsorción pueden ser descritas por fenómenos como la difusión a
través del adsorbente, difusión en los poros y en la superficie, así como adsorción poro-
superficie o por alguna combinación de estos fenómenos (Meltcalf y Eddy, 2003). Para
conocer el mecanismo del proceso de adsorción pueden utilizarse varios modelos cinéticos
como el de pseudo primer orden, pseudo-segundo orden y modelo de Elovich.
1.4.1.1 Modelo de pseudo-primer orden
En el modelo de pseudo primer orden, la velocidad de sorción es proporcional a la
concentración del adsorbato. Las constantes de sorción de este modelo se obtienen por la
ecuación de Lagergren (Tseng, et al., 2010), la cual está dada por:
Qt = Qe(l-e klt) (10)
Dónde:
k= constante cinética de pseudo-primer orden (min x)
qe = cantidad de adsorbente en el equilibrio (mg/g)
qt = cantidad de adsorbente al tiempo t (min)
t = tiempo (min)
1.4.1.2 Modelo de pseudo-segundo orden
Este modelo describe una posible quimisorción (Ho y McKay, 2003) y usualmente
está representado por la siguiente ecuación :
1
((1/fc2Qe2) + (t/Qe)
Perla Tatiana Almazán Sánchez
(11)
15
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Dónde:
qe = cantidad de adsorbente en el equilibrio (mg/g)
qt = cantidad de adsorbente al tiempo t (min)
k2= es la constante de velocidad de pseudo-segundo orden (g/mg min)
t = tiempo (min)
1.4.1.3 Modelo de Elovich
La ecuación de Elovich presentada en 1939; explica fenómenos de adsorción
química y es apropiado para sistemas con superficies adsorbentes heterogéneas; este
modelo era empleado sólo en la adsorción de gases (Aharoni y Tompkins, 1970, Wu et al.,
2009); pero en años recientes, se ha utilizado para describir la adsorción de contaminantes
en solución acuosa (Wu et al., 2009, El-Naas et al., 2010). La ecuación de este modelo está
dada por:
1qt = ln(1 + (abt) (12)
Dónde:
qt = cantidad de adsorbato adsorbido (mg/g)
a= velocidad de adsorción (mg/g/min)
1/b= parámetro relacionado al número de sitios activos para la adsorción (mg/g)
t= tiempo (min)
1.4.2 Isotermas de adsorción
La adsorción es un proceso que tiene como objetivo la remoción de un soluto de
una solución y la concentración de este en la superficie del adsorbente hasta que la cantidad
de soluto removido está en equilibrio con la superficie. Este equilibrio es descrito
expresando la cantidad de soluto adsorbido por unidad de masa del adsorbente (qe) como
Perla Tatiana Almazán Sánchez 16
“Tratamientos avanzados para la remoción de un colorante de origen textil”
función de la concentración de soluto removido en la solución (Ce). Una expresión de este
tipo es denominado isoterma de adsorción (El-Naas et al., 2010).
1.4.2.1 Ecuación de isoterma de Langmuir
El modelo de Langmuir considera que la sorción se produce solamente en
determinados lugares y no hay una interacción entre las moléculas retenidas (Ahmad y
Hameed, 2009, Langmuir, 1916).
Este modelo está descrito por la siguiente ecuación:
_ QmbCe1+bCe
(13)
Dónde:
qm = Cantidad de soluto adsorbido por unidad de peso o adsorbente necesario para formar
una monocapa en la superficie (mg/g)
b= Constante relacionada con la energía o la entalpía neta de la adsorción
Ce = Concentración de adsorbato en la solución al equilibrio (mg/L)
1.4.2.2 Ecuación de isoterma de Freundlich
Este modelo muestra la adsorción en superficies heterogéneas (Freundlich, 1906)
y se describe en la Ec. 14; relaciona la distribución de un soluto y refleja las interacciones
intermoleculares del soluto en ambas fases (de D. Casquero-Ruiz et al., 1988).
?«= WCU") (14)
Dónde:
Perla Tatiana Almazán Sánchez 17
“Tratamientos avanzados para la remoción de un colorante de origen textil”
qe = Cantidad de adsorbato por unidad de adsorbente (mg/g)
Kf = Constante de equilibrio que indica la capacidad de adsorción
1/n= Constante de adsorción que indica la heterogeneidad de la superficie del adsorbente
Ce = Concentración de adsorbato en solución al equilibrio (mg/L)
1.4.3 Columnas de adsorción
La adsorción en columna tiene diversas ventajas, entre las que se encuentran el alto
campo de operaciones y el escalamiento de los estudios en laboratorio. Este procedimiento
se realiza en un sólo paso, ya que un volumen grande de aguas residuales puede ser tratado
en forma continua usando una cantidad definida de adsorbente empacado en la columna
(Cooney, 1999; Metcalf y Eddy, 2003). Al final del proceso, la carga de contaminantes
puede ser concentrada en volúmenes pequeños para recuperarse, disponerse o contenerse
en depósitos adecuados (Aksu y Gonen, 2004).
1.4.3.1 Modelos de adsorción en columna
Para realizar un proceso de adsorción, es necesario el conocimiento de la cinética
de adsorción ya que el comportamiento dinámico en el lecho fijo es muy valioso para el
cálculo de los proceso de adsorción. Diversos modelos han sido construidos basándose en
ecuaciones de balance de masa para la predicción de curvas de ruptura.
1.4.3.1.1 Modelo de Thomas
El diseño exitoso de un tratamiento de adsorción en columna, requiere de la
predicción de concentración-tiempo o curva de ruptura para el efluente y la determinación
de la capacidad máxima de adsorción de un adsorbente (Han et al., 2007). La ecuación del
modelo de Thomas asume que los datos tienen un comportamiento de isoterma de
Langmuir, mientras que la cinética obedece al modelo de segundo orden (Han et al., 2009).
Este modelo está descrito por la siguiente ecuación:
Perla Tatiana Almazán Sánchez 18
“Tratamientos avanzados para la remoción de un colorante de origen textil”
£o ________1________ (15)
Dónde:
C0 = Concentración inicial del influente (mg/L)
Ct = Concentración de efluente (mg/L)
Kt = Constante de velocidad de Thomas (L/mg/min)
q0 =Capacidad de sorción del adsorbente (mg/g)
Q =Flujo volumétrico (L/min)
M =Masa del sorbente en la columna (g)
tb =Tiempo de ruptura de la columna (min)
1.4.3.1.2. Modelo de Bohart-Adams
Las ecuaciones fundamentales que describen la relación entre Ce/C0 y t en un
sistema en continuo fueron establecidos por (Bohart y Adams, 1920). Este modelo es usado
para describir la parte inicial de la curva de ruptura (Han et al., 2009), además muestra que
la velocidad de adsorción es proporcional a la capacidad residual del adsorbente y la
concentración de las especies adsorbidas. Es usado principalmente para simular curvas de
ruptura y predecir el escalamiento de una planta industrial (Khim Hoong, 2010). Este
modelo está descrito por la siguiente ecuación:
z£o = e(KBAcot~KBANOCt
Dónde:
C0 = Concentración inicial del influente (mg/L)
Ct = Concentración de efluente (mg/L)
Perla Tatiana Almazán Sánchez 19
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Kba =Constante de velocidad de Bohart-Adams (L/mg/min)
N0 =Capacidad de sorción por volumen del adsorbente (mg/L adsorbente)
Z =Altura del lecho (cm)
F =Velocidad lineal (cm/min)
tb =Tiempo de ruptura (min)
1.4.3.1.3 Modelo de Yoon-Nelson
Este modelo es aplicado para minimizar el error resultante del modelo de Thomas.
Además de que no requiere datos adicionales para el cálculo de las constantes. La Ec. 17
describe este modelo:
Ct _ e(KYNt-T:KYN)Co = 1+ e(KYNt-TKYN) ( )
Dónde:
C0 = Concentración inicial del influente (mg/L)
Ct = Concentración de efluente (mg/L)
Kyn =Constante de velocidad de Yoon-Nelson (L/min)
t = Tiempo necesario para adsorber un 50% de adsorbato (min).
La Ec. 18 permite calcular la capacidad de adsorción de la columna a partir de las
constantes obtenida por el modelo de Yoon-Nelson.
Qoyn = Q
1 _ C0Qt (18)2 m mm m
Dónde:
Perla Tatiana Almazán Sánchez 20
“Tratamientos avanzados para la remoción de un colorante de origen textil”
C0 = Concentración inicial del influente (mg/L)
qYN =Capacidad de adsorción (mg/g)
Q = Flujo de entrada (L/min)
m =Masa del adsorbente (g)
1.5 Aplicación de la energía solar en el tratamiento de las aguas residuales
La energía solar es una fuente de energía alternativa que en los últimos años ha
tenido gran relevancia debido al acelerado agotamiento de los recursos fósiles, ya que este
tipo de energía puede ser utilizada en diversas actividades como la cocción de alimentos,
calentadores de agua, generación de energía eléctrica, entre otros (Tapia S y del Río P,
2009). Debido a que la radiación solar que llega al planeta es baja, es necesario
implementar sistemas de concentración como los concentradores parabólicos compuestos
(CPC) que permitan aprovechar este tipo de energía, siendo los dispositivos que ayudan a
concentrar dicha radiación. Aunque la principal aplicación de los CPC fue concentrar la
radiación infrarroja para obtener calor, la radiación UV también puede ser concentrada y
aprovechada para el tratamiento de las aguas residuales, pues la principal fuente de
radiación UV son lámparas de mercurio (Mbonimpa et al., 2012) que llegan a tener tiempos
de vida muy cortos, además de la alta toxicidad del mercurio.
1.5.1 Concentradores parabólicos compuestos
Los concentradores parabólicos compuestos fueron aplicados inicialmente como
instrumentos para la detección de radiación de alta energía desde 1996 en Estados Unidos
por Hinterberger y Wiston (1966), en Alemania por Ploke y en la URSS por Baranov y
Melinikov; mientras que Winston (1974) y Rabl (1976) describieron su aplicación en la
concentración de energía solar dando las bases para la aplicación y desarrollo de estos
dispositivos (Winston, 1974, Duffie y Beckman, 2013, Tapia S y del Río P, 2009).
Perla Tatiana Almazán Sánchez 21
“Tratamientos avanzados para la remoción de un colorante de origen textil”
1.5.1.1 Concentrador en dos dimensiones (CPC-2D)
La figura 6 muestra como está conformado un concentrador parabólico compuesto,
donde cada lado del CPC se integra por dos segmentos de parábola, los cuales son espejo
uno del otro, y se ubican de forma simétrica con respecto a un eje vertical en el centro de
ambos. El ángulo entre el eje del CPC y la línea que conecta el foco de una de las parábolas
con el borde opuesto de la apertura es llamado ángulo de aceptación (6max) (Duffie y
Beckman, 2013).
Los parámetros geométricos del CPC-2D son la longitud de apertura de entrada a,
longitud de apertura de salida a', longitud de la altura L y la longitud del ancho del
dispositivo l; el área de incidencia de los rayos o de apertura A y el área de salida de los
rayos las áreas A' (Tapia y del Río, 2009).
Fig. 6 Aspecto físico del CPC-2D (a) y ángulo de aceptación del CPC (b)
Las ecuaciones que describen la parábola que conforman el CPC se escriben en
coordenadas polares (r, t) con origen en el foco F, si se denomina a la distancia focal como
f, la parábola puede definirse como (Ec. 19):
r = 2f1-sin t
Perla Tatiana Almazán Sánchez
(19)
22
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Con esta ecuación es posible determinar los parámetros geométricos del CPC en
función del área de salida del concentrador y el ángulo de incidencia. Así, la distancia focal
se determina por la Ec. 20:
f = a'(1 + sin 6max) (20)
La longitud total queda establecida por la Ec. 21 y el área de entrada por la Ec. 22
gf(l+sin Omax) cos ®max
(sin 0max)2 (21)
a!
sin ®max(22)
El factor de concentración (C) del CPC-2D es calculado por la ecuación 23, este factor
permite calcular el ángulo de aceptación (Ec. 24) necesario para obtener la ecuación de la
parábola:
2al
2a'l(23)
0 = sin 11 c
(24)
Por tanto, las ecuaciones que describen la parábola son:
r¡(t) =x(t) = 2a' ((1+sin9~)cos(t+9~) -1)
l-sin t 2)
y(t) = 2a'((1+sin9)ssint(t+9))-e <t<--2Q
2(25)
Perla Tatiana Almazán Sánchez 23
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Los concentradores parabólicos compuestos han sido aplicados para llevar a cabo el
tratamiento de aguas residuales, específicamente en los procesos de fotocatálisis usando
óxido de titanio (TiO2) (Salgado-Tránsito et al., 2015), en el proceso de foto-Fenton
homogéneo (Velegraki y Mantzavinos, 2015) y heterogéneo que promueven la oxidación
de materia orgánica, así como la desinfección que es la eliminación de microorganismos
patógenos presentes en las aguas naturales y residuales (Mbonimpa et al., 2012).
Perla Tatiana Almazán Sánchez 24
“Tratamientos avanzados para la remoción de un colorante de origen textil”
2. JUSTIFICACIÓN E
HIPÓTESIS
Perla Tatiana Almazán Sánchez 25
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
2.1 JUSTIFICACIÓN CONTEXTUAL Y CIENTÍFICA
La descarga de efluentes de la industria textil con una alta concentración de
colorantes ocasiona daños ambientales severos, debido a su baja biodegradabilidad, cuya
presencia en el agua provoca efectos perjudiciales en flora y fauna acuáticos. La
contaminación de agua por colorantes textiles es un problema ambiental actual en
Almoloya del Río, Estado de México, donde la manufactura de prendas de mezclilla es
una de las principales actividades económicas y que puede ocasionar impactos ambientales
adversos. El desarrollo de métodos de tratamiento eficientes y económicamente factibles,
que permitan minimizar este problema, es de interés en esta investigación.
En principio, se contempló la modificación electroquímica, propuesta por Teutli-
Sequeira et al., 2013, de una arcilla y un carbón activado (materiales de soporte),
empleando electrodos de hierro y cobre, respectivamente, para efectuar la adsorción de un
colorante utilizado para el teñido de prendas de mezclilla en solución acuosa y en un
efluente de origen textil. El material adsorbente fue regenerado mediante los procesos de
Fenton y foto-Fenton, donde los iones de Fe y Cu soportados en la arcilla y el carbón
activado propiciaron la generación de radicales hidroxilo (•OH) a partir de peróxido de
hidrógeno, oxidando el colorante adsorbido y por lo tanto promoviendo la regeneración y
reutilización del material en varios ciclos.
El inconveniente que presenta el proceso de Fenton y foto-Fenton homogéneo en
medio acuoso, es la generación de hidróxidos de hierro que requieren un tratamiento
adicional. En el caso del proceso de Fenton y foto-Fenton heterogéneo, una de las
propuestas de este trabajo, los iones de hierro y cobre fueron soportados en el material,
evitando la formación de lodos y favoreciendo su regeneración. Es importante mencionar
que la modificación de materiales empleados para el proceso Fenton y foto-Fenton
heterogéneo, usualmente se realiza con sales de Fe2+ o Fe3+; empero, se propuso la
modificación por métodos electroquímicos y evaluando estos procesos de oxidación
(Fenton y foto-Fenton heterogéneo) en solución acuosa y en un efluente textil, para evaluar
en un mismo paso, la remoción del colorante del medio acuoso y la regeneración del
Perla Tatiana Almazán Sánchez 26
“Tratamientos avanzados para la remoción de un colorante de origen textil”
material. Para el proceso de foto-Fenton se implementó un concentrador parabólico
compuesto CPC-2D para concentrar radiación UV proveniente del sol.
Es por ello, que en este trabajo de investigación, se efectuó la modificación
electroquímica de una arcilla y un carbón activado con electrodos de hierro y cobre, para
su aplicación en los tratamientos avanzados de adsorción, Fenton y foto-Fenton
heterogéneo en la remoción de un colorante textil utilizado en el acabado de prendas de
mezclilla.
2.2. HIPÓTESIS
Los materiales arcilla y carbón activado modificados electroquímicamente son
eficientes para la remoción de un colorante textil presente en medio acuoso mediante los
tratamientos avanzados de adsorción y oxidación Fenton y foto-Fenton heterogéneo.
Perla Tatiana Almazán Sánchez 27
“Tratamientos avanzados para la remoción de un colorante de origen textil”
3. OBJETIVOS
Perla Tatiana Almazán Sánchez 28
“Tratamientos avanzados para la remoción de un colorante de origen textil”
3.1 Objetivo general
Desarrollar la modificación de una arcilla y un carbón activado
electroquímicamente que promuevan la adsorción y oxidación avanzada de un colorante
textil utilizado en el acabado de prendas de mezclilla.
3.2 Objetivos específicos
1. Modificar un carbón activado y una arcilla por métodos electroquímicos para
depositar iones de hierro y cobre.
2. Caracterizar los materiales adsorbentes modificados y sin modificar mediante
microscopía electrónica de barrido (MEB), espectrofotometría de dispersión de
energía (EDS), análisis de Brunauer Emmet Teller (BET) y difracción de rayos X
para conocer su estructura y composición.
3. Caracterizar fisicoquímicamente el efluente proveniente de una lavandería de
acabado de prendas de mezclilla.
4. Realizar cinéticas e isotermas de adsorción del colorante en solución acuosa y del
efluente proveniente de una lavandería de acabado de prendas de mezclilla, así como
columnas de adsorción con el agua residual.
5. Evaluar ciclos de adsorción-regeneración de los materiales más eficientes, mediante
la aplicación del proceso de Fenton y foto-Fenton.
6. Diseñar, construir e implementar un concentrador parabólico compuesto CPC-2D
para concentrar radiación UV proveniente del sol
7. Realizar la oxidación avanzada por el proceso de foto-Fenton heterogéneo solar del
colorante en solución acuosa y en el efluente de la lavandería, empleando los
adsorbentes modificados.
Perla Tatiana Almazán Sánchez 29
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4. METODOLOGÍA
Perla Tatiana Almazán Sánchez 30
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4. METODOLOGÍA
4.1 Diagrama de bloques
En el diagrama de la figura 7 se muestra un esquema general de la metodología
que se realizó en este trabajo de investigación.’---------------------- '
Modificaciónelectroquímica de
materiales*
Caracterización de materiales adsorbentes
*
'---------------------- 'Preparación de solución acuosa
del colorante
*Pruebas de adsorción a
diferentes valores de pH
♦
Evaluación de ciclos de
adsorción-regeneración
Regeneración de materiales
(Fenton y foto- Fenton)
Cinéticas eisotermas de adsorción.
-
Muestreo de aguaresidual y
caracterización
Evaluación de columnas de adsorción.
*Diseño y
construcción de concentrador
CPC-2D
*Proceso de Fenton y
foto-Fenton heterogéneno.
Fig. 7 Diagrama de bloques de la metodología
4.2 Selección de los adsorbentes
Se utilizaron dos materiales abundantes y de fácil disponibilidad como es la arcilla
y el carbón activado; ambos comerciales. En el caso de la arcilla, es la montmorillonita
(Mt-KSF) de la marca Fluka Chemika y el carbón activado (AC-N) es de origen vegetal
lavado con ácido de la marca Clarimex.
4.3 Modificación electroquímica de materiales
Se realizó la modificación electroquímica de los materiales adsorbentes
seleccionados, empleando electrodos de hierro y cobre metálicos, con un área superficial
de 0.0019 m2. La Figura 7 muestra cómo se realizó la modificación de los materiales. El
sistema consistió en una celda electroquímica empleando dos electrodos en forma paralela,
los cuales se pusieron en contacto con 10 g de arcilla o carbón, suspendidos en 80 mL de
Perla Tatiana Almazán Sánchez 31
“Tratamientos avanzados para la remoción de un colorante de origen textil”
agua desionizada, aplicando una intensidad de corriente de 0.5 A y variando el tiempo de
modificación, que de acuerdo con la ley de Faraday (Ec. 26) es posible calcular la cantidad
teórica producida en los sistemas electroquímicos, la cual fue fijada en 0.25, 0.50 y 0.75 g
de Fe y cobre. La Tabla 3 muestra los tiempos usados para la modificación.
MIt
zF(26)
Dónde:
N= masa de Fe3+ o Cu2+ (g de Fe3+ o Cu2+)
M= peso molecular del hierro o cobre (g/mol)
z= numero de electrones en la reacción (Fe=3 y Cu=2)
F= constante de Faraday (96500 C/mol). 1C=A's
t= tiempo (s)
/= intensidad de corriente (s)
Tabla 3 Tiempo requerido para la modificación de la arcilla y el carbón activado
Cantidad teórica (g)
t (min)Fe Cu
0.25 43 250.50 87 510.75 130 76
En un inicio, se realizó la modificación electroquímica a un pH menor a 2, ajustado
con ácido clorhídrico, mismo que fue usado como electrolito soporte para favorecer la
conductividad eléctrica. Sin embargo al realizar la caracterización de los materiales por
EDS, en algunos de ellos no fueron fijados los iones metálicos. Por tal motivo, la
modificación de la arcilla con hierro y cobre se realizó a un valor de pH 7, mientras que el
carbón fue modificado sin controlar el pH del sistema, a un tiempo de 130 min y 76 min
para hierro y cobre respectivamente.
Perla Tatiana Almazán Sánchez 32
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Se determinó la concentración de hierro y cobre producida en el sistema
electrolítico para comparar con la concentración real obtenida y la teórica calculada por la
ley de Faraday. La determinación fue por espectrofotometría de absorción atómica.
Los materiales modificados se filtraron, se lavaron con agua desionizada y se
pusieron a secar a 90 °C por 18 h.
Electrodos de Fe o Cu
Electro-disolución del ánodo Fe o Cu
Fijación de iones Fe2+ o Cu+ en el
materialAgitaciónmagnética
Fig. 8 Celda electroquímica para la modificación de los materiales adsorbente
4.4 Caracterización del material adsorbente
4.4.1 Microscopía Electrónica de Barrido (MEB) y Microanálisis elemental por
espectroscopia de rayos X de energía dispersa (EDS)
Esta técnica permite conocer la morfología del material así como los elementos que
contiene y que porcentaje en peso que representan en la muestra. Este análisis se realizó
utilizando un microscopio de alto vacío de la marca Jeol JSM-6610LV. La amplitud de las
micrografías tomadas fue a 2000 aumentos.
Perla Tatiana Almazán Sánchez 33
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4.4.2 Difracción de Rayos X
Este análisis permite conocer los componentes del material, así cómo saber si es
amorfo o cristalino. La técnica se desarrolló utilizando un equipo de difracción de la marca
Siemens D500 acoplado con un tubo de rayos X con ánodo de cobre.
4.4.3 Análisis de BET
La técnica de Brunauer Emmet Teller (BET), es un método usado para determinar
el área específica de los materiales, así como el diámetro y volumen de poro. Este análisis
se realizó con un equipo de la marca Micrometrics modelo Gemini 2360; las muestras se
mantuvieron en acondicionamiento a una temperatura de 200°C por 2 h.
4.4.4 Determinación del punto cero de carga
La determinación del punto cero de carga se llevó a cabo utilizando 100 mg del
adsorbente y 10 mL de una solución 0.1 M de perclorato de sodio; se evaluaron valores de
pH de 2 a 10. El valor del pH fue ajustado con soluciones 0.05 M de ácido clorhídrico
(HCl) o hidróxido de sodio (NaOH). Después de un tiempo de contacto de 72 h, las
muestras fueron centrifugadas y filtradas y se determinó el pH de los filtrados con un
potenciómetro STAT Controller MeterLab PHM.
4.4.5 Determinación de hierro y cobre
Se determinó el contenido de Fe y Cu en los materiales naturales y modificados
con Fe y Cu utilizando 250 mg de cada material, 45 mL de agua desionizada y una mezcla
2:1 de ácido nítrico y clorhídrico concentrados. La mezcla se trasladó a un vaso de teflón
y se trató en el digestor de microondas CEM. La concentración de Fe y Cu se determinó
por absorción atómica usando un espectrofotómetro Varian SpectrAA-600.
Perla Tatiana Almazán Sánchez 34
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4.5 Preparación de soluciones acuosas del colorante
Se prepararon soluciones acuosas de un colorante utilizado en el teñido de la
mezclilla, con una concentración de 10, 100 y 1000 mg/L; el cual fue obtenido en una
lavandería de acabados textiles del municipio de Almoloya del Rio. Las soluciones se
prepararon con agua desionizada.
4.5.1 Caracterización del colorante
El colorante fue caracterizado en polvo y en solución acuosa por infrarrojo (IR) con
un equipo infrarrojo con transformada de Fourier modo HART IR-Prestige-2, para
identificar los principales grupos funcionales presentes. El colorante en solución acuosa
también fue caracterizado por espectrofotometría UV-Visible, para identificar la banda de
máxima absorción en la zona visible del espectro electromagnético, para ello se utilizó un
espectrofotómetro UV-Visible Varian Carey. A partir de la longitud de onda identificada
(591 nm), se procedió a realizar una curva de calibración para evaluar la concentración del
colorante en los diferentes experimentos realizados.
4.6 Muestreo del efluente textil
Se realizó el muestreo simple (NMX-AA-003-1980) de un agua residual
proveniente de las tinas de enjuague de una lavandería de acabados de prendas de
mezclilla, ubicada en el municipio de Almoloya del Rio. La lavandería de donde se obtuvo
la muestra de agua es de acabados de mezclilla, que consisten en un deslavado, suavizado
y decorado de la tela, donde emplean productos como detergentes líquidos, suavizantes,
sal de mar, piedra pómez, entre otros.
4.7 Caracterización fisicoquímica del efluente textil de acabado de prendas de
mezclilla
El agua residual se caracterizó evaluando los parámetros presentados en la tabla 4:
Perla Tatiana Almazán Sánchez 35
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Tabla 4 Parámetros fisicoquímicos para análisis de agua residual
Parámetro NormapH NMX-AA-008-SCFI-2000Color NMX-AA-045-SCFI-2001Acidez y alcalinidad NMX-AA-036-SCFI-2001Dureza NMX-AA-072-SCFI-2001Sulfatos NMX-AA-074-1981Cloruros (Cl“) NMX-AA-073-SCFI-2001Demanda Química de Oxígeno (DQO) NMX-AA-030-SCFI-2001Demanda Bioquímica de Oxígeno (DBO5) NMX-AA-028-SCFI-2001Carbono Orgánico Total (COT) Método de combustiónNitrógeno amoniacal Método HachNitratos (NO3) Método HachFósforo total (Pt) NMX-AA-029-SCFI-2001Turbidez NMX-AA-038-SCFI-2001Conductividad Eléctrica NMX-AA-093-SCFI-2000Sustancias activas al azul de metileno (SAAM) NMX-AA-039-SCFI-2001Sodio, Calcio, Potasio, Magnesio NMX-AA-051-SCFI-2001
4.8 Pruebas de sorción evaluando el efecto del pH en soluciones acuosas del
colorante
Se realizaron pruebas de sorción con los materiales naturales y modificados
evaluando valores de pH de 2, 4, 6, 8 y 10, el pH fue ajustado con ácido clorhídrico o
hidróxido de sodio. Se utilizó una dosis del adsorbente de 100 mg y 10 mL de solución
acuosa con una concentración del colorante de 10 mg/L. El tiempo de contacto fue de 5
días. Se evaluó el porcentaje de remoción del colorante. La tabla 5 describe los materiales
utilizados en este proceso, así como las siglas de identificación.
Perla Tatiana Almazán Sánchez 36
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Tabla 5 Materiales utilizados en las pruebas de adsorción a diferentes valores de pH.
Material DescripciónMt-KSF Arcilla naturalMt-Fe-2 Arcilla modificada con hierro a pH 2Mt-Fe-7 Arcilla modificada con hierro a pH 7Mt-Cu-2 Arcilla modificada con cobre a pH 2Mt-Cu-7 Arcilla modificada con cobre a pH 7
AC-N Carbón activado naturalAC-Fe-2 Carbón modificado con hierro a pH 2AC-Fe-7 Carbón modificado con hierro a pH 7AC-Cu-2 Carbón modificado con cobre a pH 2AC-Cu-7 Carbón modificado con cobre a pH 7
4.9 Cinéticas de adsorción
4.9.1 Solución acuosa del colorante
Se prepararon soluciones acuosas del colorante trisulfonato potásico de índigo para
evaluar cinéticas de adsorción. Para ello se colocaron en un vial 0.100 g de la arcilla natural
(Mt-KSF), la arcilla modificada con Fe (Mt-Fe-7) y Cu (Mt-Cu-7), el carbón natural (AC-
N) o el modificado con cobre (AC-Cu-2), se adicionaron 10 mL de la solución del
colorante con una concentración inicial de 100 mg/L y un valor del pH de 6.2, se colocaron
en un baño de agitación a una temperatura de 30 °C y se evaluaron tiempos de contacto de
5, 15, 30, 60, 180, 300, 420, 1440, 2880 y 4320 min. Las muestras fueron centrifugadas,
filtradas y se determinó la concentración del colorante usando un espectrofotómetro Perkin
Elmer Lamba 10 a 591 nm. Los datos obtenidos fueron analizados aplicando los modelos
de cinéticas de adsorción de pseudo-primer y pseudo-segundo orden y el modelo de
Elovich
4.9.2 Agua residual
Se realizaron cinéticas de sorción con el agua residual utilizando 0.150 g de la
arcilla natural (Mt-KSF), la arcilla modificada con hierro (Mt-Fe-7), el carbón natural (AC-
N) o el modificado con cobre (AC-Cu-2), se adicionaron 15 mL del agua en estudio con
Perla Tatiana Almazán Sánchez 37
“Tratamientos avanzados para la remoción de un colorante de origen textil”
un valor de pH de 6.8. Las muestras se colocaron en un baño de agitación a 30 °C y se
evaluaron tiempos de contacto de 5, 15, 30, 60, 180, 300, 420, 1440, 2880, 4320 y 5760
min. Las muestras fueron centrifugadas, filtradas y se determinaron los parámetros de
DQO, color y COT para conocer el tiempo de equilibrio del sistema de adsorción. Se
aplicaron los modelos cinéticos de adsorción (pseudo primer y pseudo segundo orden y el
modelo de Elovich). En el caso de la determinación de DQO y color se utilizó un
espectrofotómetro Hach DR 890 y para el COT se utilizó un analizador de COT (O. I.
Analytical 1020A). A los datos obtenidos se les aplicaron los modelos de adsorción de
pseudo-primer y pseudo-segundo orden y el modelo de Elovich.
4.10 Isotermas de adsorción
4.10.1 Soluciones acuosas del colorante
Se realizaron isotermas con el colorante trisulfonato potásico de índigo empleando
una dosis de 0.100 g de Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N o AC-Cu-2 y se adicionaron
10 mL de la solución del colorante, en este caso los experimentos se realizaron variando
la concentración del colorante de 10 a 100 mg/L. Las muestras se pusieron en un baño de
agitación a 30 °C con un tiempo de contacto de 24 h para Mt-KSF, de 72 h para Mt-Fe-7,
Mt-Cu-7 y AC-Cu-2 y de 96 h para AC-N. Al término del experimento, las muestras fueron
centrifugadas y filtradas; se determinó la concentración del colorante utilizando un
espectrofotómetro UV-Vis de la marca Perkin Elmer Lamba 10 a 591 nm.
4.10.2 Agua residual
Las isotermas de adsorción del agua residual se realizaron a un tiempo de equilibrio
de 4320 min (72 h). En estos experimentos se varió la dosis del adsorbente, mismo que fue
de 0.020, 0.050, 0.080, 0.100, 0.120, 0.150, 0.180, 0.200, 0.250 y 0.300 g de Mt-KSF, Mt-
Fe-7, AC-N o AC-Cu-2 y un volumen de agua residual de 15 mL y se pusieron en contacto
en un baño de agitación a 30 °C. Al término del tiempo de contacto, las muestras se
Perla Tatiana Almazán Sánchez 38
“Tratamientos avanzados para la remoción de un colorante de origen textil”
centrifugaron y se filtraron. Posteriormente, se les determinó la DQO, color y COT a las
soluciones.
Por otro lado, se realizaron isotermas de adsorción diluyendo el agua residual para
evaluar la adsorción del color, la concentración de la soluciones fueron de 76-330 U Pt-
Co. A los datos obtenidos, se aplicaron los modelos de isotermas de adsorción de Langmuir
y Freundlich para obtener las constantes correspondientes.
4.11 Ciclos de adsorción-regeneración
Se realizaron ciclos de adsorción-regeneración de los materiales utilizados en los
procesos de adsorción del colorante trisulfonato potásico de índigo. Las pruebas de
adsorción del colorante fueron con 0.100 g de adsorbente y 10 mL de una solución acuosa
con una concentración del colorante de 100 mg/L y al tiempo de contacto de 24 h para Mt-
KSF, de 72 h para Mt-Fe-7, M-Cu-7 y AC-Cu-2 de 72 h y de 96 h para AC-N.
Los ciclos de adsorción-regeneración del agua residual se realizaron empleando
150 mg de Mt-KSF, Mt-Fe-7, AC-N y AC-Cu-2, así como 15 mL de agua residual, con un
tiempo de contacto de 72 h. Los parámetros de estudio fueron la demanda química de
oxígeno (DQO), carbón orgánico total (COT) y color.
Los materiales utilizados después de la adsorción se enjuagaron con agua para
quitar remanentes de la solución acuosa y se regeneraron adicionando 1.0 mL de una
solución acuosa 1:1 de peróxido de hidrógeno (H2O2 al 30%). La regeneración se llevó a
cabo evaluando los sistemas en ausencia y presencia de luz solar; en el caso de los
experimentos en ausencia de luz se colocaron en una caja de plástico negra para evitar el
contacto con la luz; mientras que las pruebas realizadas en presencia de luz se colocaron
bajo los rayos del sol. El tiempo de regeneración fue de 4.5 h. Los materiales regenerados
fueron lavados con agua y centrifugados para eliminar los residuos de peróxido de
hidrógeno y posteriormente se pusieron a secar a 90 °C por 4 h. Una vez secos los
materiales regenerados, se reutilizaron efectuando el mismo procedimiento descrito
anteriormente durante cuatro veces más.
Perla Tatiana Almazán Sánchez 39
“Tratamientos avanzados para la remoción de un colorante de origen textil”
En el caso del agua residual, se realizó también la regeneración de los materiales
con agua desionizada, adicionando las mismas cantidades, tal y como se mencionó
anteriormente.
4.12 Columnas de adsorción
Se realizaron columnas de adsorción de color y COT presentes en el efluente de
una lavandería de acabados de prendas de mezclilla con los materiales Mt-KSF, Mt-Fe-7
y AC-N. Se utilizó una columna de vidrio con un diámetro interno de 1.5 cm.
En el caso de las muestras de arcilla se usaron 1, 2 y 3 g de los adsorbentes, con
alturas de 0.9, 1.7 y 2.4 cm para Mt-KSF y de 1.1, 2.4 y 2.8 cm para Mt-Fe-7 con un flujo
ascendente de 1 mL/min. Las dosis usadas en los experimentos de AC-N fueron 3, 5 y 7 g,
con alturas de 3.3, 5.4 y 8.3 cm, con un flujo descendente de 1 mL/min. Se tomaron
alícuotas a diferentes tiempos para efectuar las curvas de ruptura de color y COT. Se
aplicaron los modelos de Thomas, Yoon-Nelson y Bohart-Adams para determinar las
constantes respectivas.
4.13 Proceso de foto-Fenton heterogéneo solar
El proceso de foto-Fenton fue asistido por un concentrador parabólico compuesto
(CPC-2D), para poder concentrar radiación UV proveniente del sol y favorecer la
oxidación del colorante presente en soluciones acuosas del colorante trisulfonato potásico
de índigo y de un agua residual textil proveniente de una lavandería de acabados de prendas
de mezclilla, mientras que los catalizadores sólidos utilizados fueron la arcilla modificada
con hierro a pH 7 (Mt-Fe-7) y el carbón modificado con cobre a pH 2 (AC-Cu-2).
4.13.1 Construcción de concentrador solar CPC-2D
Los cálculos realizados para construir el concentrador solar están descritos en el
Anexo 10.1. La estructura del CPC-2D fue hecha de acero para dar el perfil parabólico y
las láminas utilizadas para reflejar los rayos UV provenientes del sol fueron hojas de
Perla Tatiana Almazán Sánchez 40
“Tratamientos avanzados para la remoción de un colorante de origen textil”
aluminio de la marca MIRO-SUN®, dichas laminas proveen una película de deposición física
de vapor (PVD, por sus siglas en inglés) que garantizan un 95% de reflexión de radiación. El
contenedor del agua residual a tratar fue hecho de vidrio considerando las medidas del área de
concentración del CPC-2D y para tratar 1L de agua. La irradiación global, infrarroja, UV-A y UV-
B fue medida utilizando los sensores Almemo 2590 durante los experimentos (10:00 am - 15:00
pm)
4.13.2 Proceso de Fenton y foto-Fenton heterogéneo.
Se llevó a cabo el proceso de oxidación del color utilizando tres dosis de catalizador
(0.5, 1.0 y 1.5 g) y tres dosis de peróxido de hidrógeno de la marca J. T. Baker (0.1, 0.3 y
0.5 M), el volumen de agua tratada fue 1 L, y los experimentos se realizaron en presencia
y ausencia de luz solar, para evaluar efecto de la radiación UV. El agua fue recirculada
utilizando una bomba peristáltica y se tomaron alícuotas a diferentes tiempos de
tratamiento. La concentración de colorante en las soluciones acuosas fue de 28-30 mg/L y
se determinó su concentración empleando un espectrofotómetro UV-Vis de la marca Cary
Varian; para el caso del agua residual, el parámetro analizado fue el color. El proceso de
oxidación se llevó a cabo a valores de pH de 7 y 6.86 para las soluciones acuosas y el agua
residual respectivamente.
Finalmente se evaluó un ciclo catalítico de los materiales utilizados para el proceso
de oxidación. Para ello, los materiales utilizados fueron lavados con agua desionizada y
secados a 90 °C por 3 h y después se reutilizaron una vez más en el tratamiento del agua
residual textil y las soluciones acuosas.
Perla Tatiana Almazán Sánchez 41
“Tratamientos avanzados para la remoción de un colorante de origen textil”
5. RESULTADOS
Perla Tatiana Almazán Sánchez 42
“Tratamientos avanzados para la remoción de un colorante de origen textil”
RESULTADOS
5.1. Primer artículo de investigación
En esta sección se muestra el primer artículo de investigación realizado, el que cual
se presentan los resultados obtenidos del proceso de adsorción en batch usando soluciones
acuosas del colorante trisulfonato potásico de índigo.
Adsorption-regeneration by heterogeneous Fenton process using modified carbon
and clay materials for removal of indigo blue
Perla Tatiana Almazán-Sáncheza,b, Marcos J. Solache-Ríosa, Ivonne Linares-
Hernándezb*,Verónica Martínez-Mirandab
Revista: Environmental Technology
Status: Publicado
DOI: 10.1080/09593330.2015.1133718
Perla Tatiana Almazán Sánchez 43
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ENVIRONMENTAL TECHNOLOGY, 2016http://dx.doi.org/10.1080/09593330.2015.1133718
Taylor & FrancisTaylor & Francis Group
Adsorption-regeneration by heterogeneous Fenton process using modified carbon and clay materials for removal of indigo bluePerla Tatiana Almazán-Sáncheza'b, Marcos J. Solache-Ríos3, Ivonne Linares-Hernándezb andVerónica Martínez-Mirandab'’Departamento de Química, Instituto Nacional de Investigaciones Nucleares (ININ), Ocoyoacac, Estado de México, México; “"Facultad de Ingeniería, Centro Interamerlcano de Recursos del Agua (CIRA), Universidad Autónoma del Estado de México, Unidad San Cayetano, Toluca, Estado de México, México
ABSTRACTIndigo blue dye is mainly used In dyeing of denim clothes and its presence in water bodies could have adverse effects on the aquatic system; for this reason, the objective of this study was to promote the removal of indigo blue dye from aqueous solutions by Iron and copper electrochemically modified clay and activated carbon and the saturated materials were regenerated by a Fenton-llke process. Montmorlllonite clay was modified at pH 2 and 7; activated carbon at pH 2 and pH of the system. The elemental X-ray dispersive spectroscopy analysis showed that the optimum pH for modification of montmorillonite with Iron and copper was 7 and for activated carbon was 2. The dye used in this work was characterized by Infrared. Unmodified and modified clay samples showed the highest removal efficiencies of the dye (90— 100%) In the pH Interval from 2 to 10 whereas the removal efficiencies decrease as pH Increases for samples modified at pH 2. Unmodified clay and copper-modified activated carbon at pH 2 were the most efficient activated materials for the removal of the dye. The adsorption kinetics data of all materials were best adjusted to the pseudo-second-order model, Indicating a chemisorption mechanism and the adsorption isotherms data showed that the materials have a heterogeneous surface. The Iron-modified clay could be regenerated by a photo-Fenton-like process through four adsorption-regeneration cycles, with 90% removal efficiency.
ARTICLE HISTORYReceived 14 September 2015 Accepted 14 December 2015
KEYWORDSIndigo blue; montmorillonite; activated carbon; adsorption; heterogeneous Fenton
Introduction
Synthetic dyes are widely used in diverse industries for varying purposes such as textile, cosmetic, food, pharmaceutical, paper, pulp manufacturing, dyeing of cloths, leather treatment, printing, etc. About 100,000 dyes and pigments are commercialized,[1] and the annual production is approximately 700,000 tons.[2] The textile industry is one of the most polluting industries because it uses a large amount of water; about 50% of dyes are lost in the dyeing processes and the wastewater contains chemicals and color. Dyeing is one of the most important steps in the production of textile fibers,[3] and the discharge of effluents to water bodies affects the aquatic biological activities,[4] because the dyes could be mutagens and carcinogenic [5] and absorb and reflect the sunlight, affecting the photosynthesis of aquatic plants.[6] Color is the main contaminant in wastewater, and a concentration of 10-20 mg/L of dye is sufficient to give a strong color to water.[7] Textile dyes have recalcitrant properties [8,9] and could be transformed to toxic aromatic amines.[10]
Indigo blue is one of the main dyes used in the textile industry, especially in the dyeing of denim, but its use is of great concern because it is considered a recalcitrant compound.[11] The removal of color from textile wastewaters has several problems like the wide ranges of pH intervals, salt concentrations and complex chemical struc- tures.[12] Nevertheless, efforts have been made to design and apply different treatments to remove dyes from textile effluents. Biological treatments are preferred because they are more economical and environmentally friendly,[13] although most times they are not efficient. These treatments have been applied to remove indigo dye from textile wastewater with high removal efficien- cies.[14-16] Other treatments used are chemical and physical processes such as photocatalytic degradation,[17] coagulation with bittern wastewater,[18] sonochemical degradation,[19] ion exchange,[20] ultrafiltration,[21] inverse osmosis,[22] adsorption/precipitation process,[23] coagulation/flocculation,[24] advance oxidation process such as Fenton and photo-Fenton,[25] ozonation,[26] photocatalysis with TiO2,[27] and electrochemical
CONTACT Ivonne Linares-Hernández © ivonnelinaresl 978@yahoo.com.mx
© 2016 Taylor & Francis
Perla Tatiana Almazán Sánchez 44
“Tratamientos avanzados para la remoción de un colorante de origen textil”
2 @ PT. ALMAZÁN-SÁNCHEZETAL.
processes such as electrochemical degradation with boron-doped diamond,[28,29] etc.
Adsorption is a process widely applied in textile wastewater due to excellent efficiencies in the removal of dyes.[30] This process consists of a mechanism of mass transfer where an adsorbate or contaminant is present in liquid or gas phases and it is transferred onto a solid phase (adsorbent). The main adsorbent used in wastewater treatment is the activated carbon due to its high adsorption capacity to eliminate inorganic and organic matter [31]; however, it is not the only adsorbent used in the removal of dyes - there are other materials such as rice hush ashes,[32] natural zeolites as clinoptilolite,[33] and synthetic zeolites,[34] and also clays such as bentonite [35] or montmorillonite [36] have been applied. The successful application of an adsorption process lies in the use of cheap adsorbents that are easily available, efficient and involve simple regeneration.
Nowadays, the development of new adsorbents or the modification of natural materials Is very important because these treatments can improve their adsorption capacities and increase the adsorption-regeneration cycles. The modifying processes employed are the acid/base treatments, surfactant impregnations [37] or ion exchange using iron salts such as FeCI3 or FeSO4 in the modification of zeolites [33,38] and clays [36]; this last material has been pillared with Fe to increase its specific surface area [39]; activated carbon has been also modified with FeCI3. The use of transition metals for the modification of materials is interesting because they have the capacity to form complexes with organic and inorganic compounds. Trujillo-Reyes et al. [40,41] used nanoparticles of Fe/Cu and Fe/Ni to remove denim blue from water.
Recently, electrochemical treatments have been applied to modify some adsorbents, Teutli-Sequeira et al. modified clinoptilolite, hematite and calcite with aluminum electrodes and the materials were used to remove fluoride ions,[42] Vazquez-Mejia et al. [43] used iron and aluminum electrodes to modified clinoptilolite and pumocite to remove fluorine and arsenic (V) from aqueous solutions. Almazan-Sánchez et al. [44] used iron electrodes to modify activated carbon and it was applied for the treatment of methyl methacrylate (MMA) wastewater. In all cases the electrochemical modifications improved the adsorption properties of the materials. The presence of iron and copper in the adsorbents may catalyze the oxidation of the organic matter in the presence of hydrogen peroxide (Fenton-like process).
The objective of this work was twofold; first to remove indigo blue dye from aqueous solutions using clay and an activated carbon modified by electrochemical
processes with iron and copper and second to regenerate the materials using the iron and copper fixed in the adsorbents as catalysts in the Fenton process.
Material and methods
Materials
The adsorbents used in this work were montmorillonite in powder from Fluka Chemika and activated carbon (Clarimex) obtained from bituminous coal with an alkaline pH and particle sizes between 1.2 and 1.4 mm.
Modification of the materials
A batch of electrochemical cells (Figure 1) was employed for the modifications of activated carbon (AC-N) and montmorillonite KSF (Mt-KSF). The electrode system is monopolar, the reactor cell contains an array of Fe or Cu electrodes, the electrode dimensions were 0.040 m long and 0.024 m wide and the anode electrode has a surface area of 0.0019 m2. A direct current (DC) power source supplied the system with 0.5 A at 2.5 V, corresponding to current density of 263.15 A/m2. Modification of the adsorbent material was performed by placing 10 g of adsorbent inside the cell with 0.08 L of deionized water. After modifications, materials were washed several times with distilled water and dried at 90°C for 18 h. The modifications were carried out as follows:
(a) The pH was 2 during copper and iron modification processes of clay (Mt-Fe-2 and Mt-Cu-2) and activated carbon (AC-Fe-2 and AC-Cu-2).
(b) The pH was not controlled during copper and iron modification processes for activated carbon (AC-Fe and AC-Cu).
(c) The pH was 7 during copper and iron modification processes for clay (Mt-Fe-7 and Mt-Cu-7).
The treatment was for 76 min for Cu and 130 min for iron. Faraday's law was used to calculate the theoretical amount of copper and iron produced in the electrochemical process (Equation (1)).
C = Mlt/zF (1)
where C is the Fe3+ or Cu2+ mass (g), M is the molecular weight of iron or copper (g/mol), z is the number of electrons in the electrochemical reaction (Fe = 3 y Cu = 2), F is Faraday's constant (C/mol), / is the current intensity (A) and f the time (s). According to the calculations, the theoretical concentrations were 9.4 g/L of iron or copper.
Perla Tatiana Almazán Sánchez 45
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ENVIRONMENTAL TECHNOLOGY @ 3
Figure 1. Electrochemical modification of montomorillonite and activated carbon.
Determination of iron and copper
250 mg of each material, 45 mL of deionized water and 5 mL of a mixture 2:1 of concentrated HNO3 and HCI solution were transferred to a Teflon vessel using a CEM microwave digester. The copper and iron concentrations were analyzed by atomic absorption spectroscopy using a Varían SpectrAA-600 spectrophotometer.
Characterization
The unmodified and modified clay and activated carbon were analyzed by scanning electron microscopy (SEM) and elemental X-ray dispersive spectroscopy (EDS) using a Jeol JSM-6610LV microscope to determine the elemental composition and the morphology.
The diffractograms of clay samples were obtained with a Siemens D500 diffractometer coupled with a copper anode X-ray tube. Conventional diffractograms were used to identify the compounds and to verify crystalline structure.
Determination of point of zero charge
The determinations of point of zero charge were carried out with 100 mg of adsorbent and 10 mL of a solution of sodium perchlorate 0.1 M at different pH values from 2 to 10. They were adjusted with HCI or NaOH 0.05 M. After 72 h of contact time, the samples were centrifuged and filtered, and finally the pH of solutions was measured with a pH STAT Controller MeterLab PHM 290.
Indigo blue dye
The Indigo blue dye was obtained from a dyeing industry located In the State of Mexico (Almoloya del Rio). Aqueous solutions of 10, 100 and 1000 mg/L of dye
were prepared using deionized water. The concentration of dye solutions was determined by using a UV-Vis spectrophotometer analyzer Varian Carey at 591 nm. The dye was characterized by using the Fourier Transform infrared (IR) spectrophotometer HART mode (IR Prestige-2). The powder and aqueous solution of dye were analyzed.
Adsorption
Adsorption experimentsKinetic adsorption was performed by using 100 mg of adsorbent (Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N, AC-Cu-2) and 10 mL of a solution of dye (100 mg/L) with initial pH of 6.5, according to revised references [33,36,40]; the mixtures were shaken In a water bath (30°C) at 120 rpm at different times (5, 15, 30, 60 180, 300, 420, 1440, 2880, 4320 and 5760 min). The samples were centrifuged and filtered, and the concentration of dye was determined by a UV-Vis spectrophotometer.
The adsorption isotherms were performed by using 100 mg of Mt-Fe-7, Mt-Cu-7, AC-N or AC-Cu-2 and 10 mL of 10-100 mg dye/L aqueous solutions and concentrations from 100 to 1000 mg dye/L for Mt-KSF. The samples were shaken in a water bath (30°C) at 120 rpm for 24 h (Mt-KSF), 72 h (Mt-Fe-7, Mt-Cu-7 and AC-Cu-2), and 96 h (AC-N). Afterwards, they were centrifuged, filtered and analyzed by a UV-VIs spectrophotometer.
Evaluation of different pH values
The effect of pH on the adsorption was determined as follows: 100 mg of each adsorbent were put in contact with 0.01 L of dye aqueous solution of 10 mg/L with constant stirring, at pH values of 2, 4, 6, 8 and 10 for 4 days
Perla Tatiana Almazán Sánchez 46
“Tratamientos avanzados para la remoción de un colorante de origen textil”
4 @ P.T. ALMAZÁN-SÁNCHEZ ETAL.
(maximum equilibrium time) at 30°C. The samples were centrifuged, filtered and analyzed as described above.
Adsorption-regeneration cycles
100 mg of each saturated material (unmodified and modified) used in adsorption processes were regenerated with 1 mL of aqueous solution 1:1 (%v/v) of hydrogen peroxide (H2O2 30%) for 4.5 h at pH of 6-7,[45] in the presence and absence of sunlight; then the materials were washed with deionized water to remove the excess of hydrogen peroxide and dried at 90°C for 3 h, and the regenerated materials were placed in contact with the dye solution at equilibrium times for four more cycles.
Results and discussion
Characterization of dye
The IR spectra of solid (Figure 2(a)) and aqueous solutions (Figure 2(b)) of dye show characteristic functional groups of indigo blue dye; they were identified as N-H stretching in aromatic amines (3500 cm-1), -OH stretching of water (3330 cm-1), -CH bonded to nitrogen or oxygen atoms (2920 cm-1), carbonyl groups (1743, 1698 cm-’), aromatic rings (1541, 605, 550 cm-1) and sulfonate group (1368, 1049 cm-1).
3950 3450 2950 2450 1950 1450 950 450
550 cm-'
Figure 2. IR spectra of dye in (a) powdered and (b) aqueous solution.
The aqueous solution of dye was compared with a standard solution of potassium indigotrisulfonate (Sigma Aldrich), and the spectra were similar (Figure 2 (b)); the dye from a dyeing industry located in the State of Mexico was found to be the same as the compound from Sigma Aldrich. The structure of potassium indigo trisulfonate is shown in Figure 2(b), and the functional groups of the compound were identified.
Adsorbents characterization
Elemental analysis of materialsThe materials were characterized by using the SEM technique. The characteristic elements of montmorillonite KSF were oxygen, silicon, aluminum, iron, magnesium and calcium, whereas the elements found for activated carbon were carbon, oxygen and silicon (Table 1). Both materials were modified with iron and copper, the clay at pH 2 and 7 and activated carbon at pH 2 and pH of the system (pH = 10). Copper was not found in the montmorillonite KSF when the modification pH was 2 and the percentage weight of iron decreased after modification; this behavior could be attributed to the acid pH conditions during the modification process, because at this pH value the metallic ions are soluble in aqueous medium, limiting their fixation on the materials. In a typical electrolytic cell, the pH increases during electrolysis due to the reduction of water in the cathode to form hydroxyl ions, but in this case the pH was maintained at 2 during the process in order to produce ionic species of iron and copper (Fe2+, Fe3+, Cu2+) in the system; then iron and copper were kept in solution. The modified samples of Mt-Fe-7 show that the iron content increased three times and the copper in the sample was 5%.
In the modified activated carbon, a similar behavior was observed with the AC-Fe-2 because the metal was not found in the material; however, Cu was present in the sample after modification at pH 2 (AC-Cu-2). The iron-modified activated carbon at pH 10 shows that iron was fixed in the sample and the content of copper was lower than the content found in the modified activated carbon at pH 2, then copper was sorbed in the pores of carbon and it was retained better than iron.
Scanning electron spectroscopyThe morphology of particles is heterogeneous (Figure 3), and they did not change after electrochemical modification as it was expected because the objective of modification was to deposit the iron and copper in the clay. The micrograph of Mt-Cu-7 (Figure 3(c)) shows some brilliant zones that, according with EDS analysis, correspond to copper particles (19.46% of copper).
Perla Tatiana Almazán Sánchez 47
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ENVIRONMENTAL TECHNOLOGY @ 5
The micrograph of AC-N (Figure 3(d)) shows particles of irregular forms. Some lamellas were observed in AC- Fe-2 (Figure 3(e)); in accordance with analysis of EDS, brilliant particles correspond to copper (35.20%) in the AC- Cu-2 sample (Figure 3(f)).
X-Ray diffraction
Mt-KSF, Mt-Fe-7 and Mt-Cu-7 were analyzed by X-Ray diffraction. The diffractogram of Mt-KSF was compared with the Joint Committee on Powder Diffraction Standards (JCPDS) and the principal diffraction peaks corresponded to montmorillonite (JCPDS 00-003-0010), muscovite (JCPDS 00-034-0175) and quartz (JCPDS 01-087-2096). The characteristic reflections of montmorillonite were identified and reflections of copper oxide II (JCPDS 00041-1364) were observed in the diffractogram of Mt- Cu-7 (Figure 4). In the diffractogram of Mt-Fe-2, the intensity of diffractions is different with respect to unmodified montmorillonite.
Quantification of iron and copper
The theoretical concentrations of iron and copper were calculated by Faraday's law (Equation (1)) and about 9.4 g/L of metals should be generated in the cell; however, only 3.24 and 0.54 g/L of iron and copper were detected, respectively. According to the absorption atomic test, 27.45 mg/g of Cu were fixed in the Mt-Cu-7, the content of iron in the Mt-KSF was 23.26 mg/g and after electrochemical modification at pH 7 it increased to 54.66 mg/g (Mt-Fe-7). 22.96 mg/g of Cu were fixed in the activated carbon (AC-Cu-2), the content of iron in AC-N was 6.55 mg Fe/g and after the modification process increased slightly to 7.1 mg/g (AC-Fe-2).
Point of zero charge
The point of zero charge (pHpzc) (Figure 5) is where the pH of an adsorbent has a net neutral charge. The points of zero charge of Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC- N and AC-Cu-2 were 2.86, 6.82, 7.445, 10.22 and 7.23, respectively. The surface of an adsorbent has a negative charge at pH values above the pHpzc and it has a positive charge at pH values below pHpzc. The pHpzc of Mt-KSF was the lowest (2.86), the highest was for AC-N (10.22) and the values for the modified materials were similar around 7, which may be an advantage for treatment of natural waters. Indigo trisulfonate is attracted by adsorbents at pH values lower than pHpzc due to the three sulfonate groups (SO3) in its structure. The drastic change in pHpzc °f Mt-KSF and Mt-Fe-7 could be attributed to the conditions of electrochemical modification, where the surface clay is probably charged with hydroxyl ions that change the pH of the surface.
Perla Tatiana Almazán Sánchez 48
“Tratamientos avanzados para la remoción de un colorante de origen textil”
6 @ P.T. ALMAZÁN-SÁNCHEZETAL.
Figure 3. Scanning electron micrographs of (a) Mt-KSF, (b) Mt-Fe-7, (c) Mt-Cu-7, (d) AC-N, (e) AC-Fe-2 and (f) AC-Cu-2.
Effect of pH
Adsorption on days
At pH 2, the removal of dye from aqueous solutions was similar (90-95%) by all adsorbents. Mt-KSF is an excellent adsorbent for the dye at all pH values evaluated with efficiency above 95%, and at pH values of 4, 6 and 10 the removal was 100%; similar behaviors were observed for iron- and copper-modified clays (Mt-Fe-7 and Mt-Cu-7). The removal efficiencies of dye by Mt-Fe-2 and Mt-Cu-2 decreased as the pH increased, and according to EDS analysis the iron content in the montmorillonite diminished after modification; therefore iron could be an Important factor in the removal of dye (Figure 6(a)).
Adsorption on activated carbon
AC-Cu-2 shows the highest removal of dye at pH values from 4 to 10 (93-100%). AC-N, AC-Fe-2, AC-Fe and AC-Cu have similar behaviors and their removal efficiencies decreased as the pH increased (Figure 6(b)). The modification of AC-Cu-2 under acidic conditions improves the incorporation of copper ions into activated carbon pores, because it shows the best removal efficiencies of dye compared with other modified samples, which could be attributed to the complex formed between copper and the activated carbon surface. The advantages of modifying AC-N with metal is the catalytic properties of iron and copper to improve the adsorption or oxidation of organic compounds.[46] Due to iron and copper being transition metals, and they show two oxidation states, they can promote a redox reaction in aqueous systems.
The pKa of dye indicates that at this pH the acid and basic conjugate species are present in the same quantities. In the adsorption process, the pH is a parameter that may change the surface charge of the adsorbent or promote the ionization of dye.[47] According to the pKa of 3.27 for indigo trisulfonate and the equilibrium pH, neutral species are absorbed by Mt-KSF and dissociated species are absorbed by the other materials. Figure 2(b) shows the structure of dye used; when it is not dissociated there are three acid protons in the molecule, showing an amphoteric behavior in aqueous solutions at different pH values; for this reason there is good removal of dye between pH 4 and 10 for some materials.
Adsorption kinetics
Adsorption kinetics of dye by Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2 were performed, with an Initial pH of dye solution of 6.2. The equilibrium time was reached in 5 minutes of contact for Mt-KSF, whereas for Mt-Fe-7 and Mt-Cu-7 the equilibrium time was reached in about 2880 min (Figure 7(a)). The equilibrium times for AC-N and AC-Cu-2 were 5760 and 4320 min, respectively (Figure 7(b)). The equilibrium pH values of solutions were around 2.8-3.0 for Mt-KSF, 6.1-6.4 for Mt-Fe-7, 6.9-7.1 for Mt-Cu-7, 8.7-9.6 for AC-N and 4.14.6 for AC-Cu-2.
The dyes are organic compounds that sometimes are acidic or basic and they are ionized in solution depending on their pKa and pH of solution [48]; different mechanics of adsorption could occur and the application of
Perla Tatiana Almazán Sánchez 49
Tratamientos avanzados para la remoción de un colorante de origen textil”
ENVIRONMENTAL TECHNOLOGY @ 7
Figure 4. X-ray diffractograms of natural and modified day (■ montmorillonite, ▲ muscovite, • quartz, *copper oxide).
20
10- 3 < □ ♦
X ♦
8- X ♦
X ▲<□ ♦
6- X ♦
Q. X >□ ♦
4- X ♦
X AC ♦ ♦ Mt-KSF □ Mt-Fe-7
2 ▲ A Mt-Cu-7 • AC-Cu-2XAC-N
i-i-------- 1--------- 1-------- 1-------- --------- 1---------1---------1----------8 -6 -4 -2 0 2 4 6 8
A pH
Figure 5. Point of zero charge of adsorbents (Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2).
kinetics models as pseudo-first and pseudo-second order and Elovich could explain the adsorption behavlor.[49] Experimental data were fitted to these models and the kinetics constants were determined.
Pseudo-first-order model
The pseudo-first order or Lagergren's model is shown in Equation (2):
= <7eO - eK,t) (2)
where K, is the sorption constant of Lagergren (1/min), qe and q, (mg/g) are the amounts of the adsorbed dye at equilibrium and at time f (min), respectively. This
Perla Tatiana Almazán Sánchez 50
“Tratamientos avanzados para la remoción de un colorante de origen textil”
8 © P.T. ALMAZÁN-SÁNCHEZETAL.
Figure 6. Removal of indigo blue at different pH values by natural and modified (a) montmorillonite clay and (b) activated carbon.
model describes the behavior of adsorption in liquid- solid systems and it was developed by Lagergren.[50] in a study about the sorption of malonic and oxalic acids using charcoal.
K,, qe and R2 constants of the Lagergren model were highest for Mt-KSF and lowest for Mt-Cu-7 (Table 2). Similar qe values were found for AC-N and AC-Cu-2 but the experimental data of AC-Cu-2 was better adjusted than unmodified activated carbon, and K, for AC-Cu-2 was higher than AC-N. Nekouei et al. [51] studied the removal of acid blue 129 from liquids using copper oxide nanopartide-modlfied activated carbon, and the K, was of 0.181 and 0.192 1/min using an initial concentration of 10 and 20 mg/L of dye. DíazGómez-TrevIño et al. [36] used montmorillonite KSF modified with iron to remove yellow remazol with K, of 8.33 1/h (0.139 1/min); these results are similar to the data found In the present work with Mt-Cu-7 (0.169 1/min).
where qe and q, Is the adsorption capacity at equilibrium (mg/g) at time f (min) and K2 is the pseudo-second-order rate constant for the adsorption process (g/mg min).
The highest value of K2 was obtained for Mt-KSF, whereas the values for this constant were similar for Mt-Fe-7 and Mt-Cu-7 (Table 2). Cottet et al. [53] used montmorillonite clay modified with Iron oxide to remove methylene blue from aqueous solutions; the Iron content in the material was 41.95% and the dye concentration used was 100 mg/L obtaining a K2 value of 26.69 x 102 h g/mg (16.01 x 104 g min/mg). Comparing with this work, the K2 value obtained for removal of Indigo blue with Mt-Fe-7 was 0.075 g min/mg; the value of the pseudo-second-order constant could be attributed to Iron in Mt-Fe-7 (15.66%).
Pseudo-second-order model
When experimental data are adjusted to this model, chemical adsorption takes place.[52] The pseudosecond-order model is expressed in Equation (3):
q( = f/(1/K2qe2) + (f/qe) (3)
Elovich model
The Elovich equation is considered a second-order model because it exhibits a chemisorption process. This model was mainly applied In the sorption of gases (gas-solid phase) but recently it also has been used to describe liquid-solid systems.[54,55] The Elovich model is represented In Equation (4):
q, = 1/bln(1 + (abt)) (4)
Figure 7. Adsorption kinetics of (a) clay samples (Mt-KSF, Mt-Fe-7, Mt-Cu-7) and carbon samples (AC-N, AC-Cu-2).
Perla Tatiana Almazán Sánchez 51
“Tratamientos avanzados para la remoción de un colorante de origen textil”
where q, is the adsorption capacity (mg/g) at time f, a is the initial adsorption rate (mg/g min) and b is the desorption constant (mg/g).
Mt-KSF shows the highest values of a and b and AC-N the lowest, indicating that AC-N has higher affinity to the dye than Mt-KSF and the b constant is of the same order of magnitude for Mt-Fe-7 and Mt-Cu-7 (Table 2). Belaid et al. [56] evaluated the removal of acid blue, basic red and reactive yellow dyes using granular activated carbon and they obtained values of 0.221, 3.4 x1012 and 0.715 mg/g min for the constant a respectively; the values obtained in this work were higher than acid blue and reactive yellow, showing stronger chemisorption.
Adsorption isotherms
Figure 8 shows the adsorption isotherms of indigo blue by Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2. The experimental data were fitted to Langmuir, Freundlich and Langmuir-Freundlich models.
Langmuir modelLangmuir model is the most common isotherm applied in a solid/llquld system,[57] and it assumes that the adsorption takes place in homogenous surfaces and the monolayer.[58] Equation (5) represents the Langmuir model:
qe = qmbLCe/l + (bLCe) (5)
where qe is the adsorption capacity at equilibrium (mg/ g), qm is the maximum adsorption capacity, Ce in the concentration of adsorbate in the liquid at equilibrium (mg/ L) and b is a adsorption constant.
According to the results (Table 3), adsorption data of Mt-Cu-7 were adjusted to the Langmuir model, obtaining a maximum adsorption capacity of 2.62 mg/g. Chaari et al. [59] used smectite clay and an activated carbon to adsorb a textile dye indanthrene blue RS; the system for both adsorbents was fitted to the Langmuir model; the maximum adsorption capacities for smectite and activated carbon were 13.92 and 20.28 mg/g, respectively, with an initial concentration of dye of 50 mg/L; these values are higher than the adsorption capacity obtained for Mt-Cu-7 in this work; however the concentration is half.
Freundlich model
This model shows that the sorption takes place on the heterogeneous surface.[60] Equation (6) represents the Freudlich model.
<7e = KFC'e/n (6)
ENVIRONMENTAL TECHNOLOGY @ 9
where qe Is the adsorption capacity at equilibrium (mg/ g), and KF and 1/n are Freundlich constants that indicated the adsorption capacity and adsorption intensity, respectively.[61] According to the correlation coefficient Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2 were best fitted to the Freundlich model (Table 3). DiazGómez- Treviño et al. [36] used Iron-modified clay to adsorb yellow remazol from water and they obtained a KF value of 13.37 ((mg/g)(L/mg)1/n); this result is very
similar to the KF constant of Mt-KSF, whereas for Mt-Fe- 7 the constant was 0.280 ((mg/g)(L/mg)1/n), indicating a low adsorption capacity. Mahmoodi et al. [62] applied activated carbon to adsorb direct blue 78 (50 mg/L) with a Kf constant of 23.85 ((mg/g)(L/mg),/n); the values obtained for AC-N and AC-Cu-2 in this work were KF = 1.351 and 1.635 ((mg/g)(L/mg)1/n), respectively.
Langmuir-Freundlich modelThe Langmuir-Freundlich isotherm is also known as Sip's equation [63] and it is represented by Equation (7):
qe = KCe'/n/l + aCe'/n (7)
where qe is the adsorption capacity at equilibrium, Ce is the concentration at equilibrium, K and a are empirical constants.
The data obtained from Mt-Cu-7, AC-N and AC-Cu-2 adsorbents could be fitted to the Langmuir-Freundlich model with correlation coefficients higher than 0.93; however, Mt-KSF and Mt-Fe-7 were not adjusted to this model. Gutiérrez-Segura et al. [33] evaluated the adsorption of indigo carmine using a Fe-zeolitic tuff and carbonaceous material from pyrolyzed sewage sludge; they obtained constants' K values of 0.10 and 4.05, respectively, whereas in this work K was 2.129, 1.63 and 1.74 for Mt-Cu-7, AC-N and AC-Cu-2, respectively.
Adsorption-regeneration cycles
The adsorption-regeneration cycles of the adsorbent were performed with hydrogen peroxide; it is an effective oxidizing agent with an oxidizing potential of 1.78 V. In the presence of a catalyzer as ferrous ions, hydroxyl radicals (’OH) are formed (Equation (8)) with an oxidation potential of 2.80 V [64]; this reaction is known as the Fenton process. Equation (9) shows the Fenton-like process with the formation of Fe3+ and hydroperoxyl radicals with an oxidizing potential of 1.70 V. The hydroperoxyl radicals can be formed using Cu as a catalyzer (Equation (10)). The principal use of the oxidants is to degrade the organic matter in an aqueous solution or solid phase. In this study, the regeneration of material was done by oxidizing the adsorbed dye on the
Perla Tatiana Almazán Sánchez 52
“Tratamientos avanzados para la remoción de un colorante de origen textil”
10 @ P.T. ALMAZÁN-SÁNCHEZ ETAL.
Table 2. Kinetic constants of sorption on unmodified and modified materials.
ModelConstants/adsorbents
Pseudo-first order Pseudo-second order Elovich
Kj (1/min) (mg/g) ft2 K2 (g/mg min) qc (mg/g) fi2 a (mg/g min) b (mg/g) R2
Mt-KSF 12.001 9.592 0.999 3.98E43 9.592 0.999 1.69E44 11.42 0.994Mt-Fe-7 0.319 7.513 0.949 0.075 7.712 0.978 2.04E8 3.892 0.990Mt-Cu-7 0.169 4.433 0.818 0.047 4.659 0.899 350.925 2.881 0.995AC-N 4.40E-4 8.198 0.827 5.43E-5 9.783 0.844 0.010 0.458 0.871AC-Cu-2 0.029 8.109 0.958 0.005 8.517 0.966 3.007 1.014 0.895
Figure 8. Adsorption isotherms of dye with (a) Mt-KSF and (b) Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2.
Table 3. Isotherm constants of Mt-KSF, Mt-Fe-7, Mt-Cu-7, AC-N and AC-Cu-2.
Model Constants
Adsorbents
Mt-KSF
Mt-Fe-7
Mt-Cu-7 AC-N
AC-Cu-2
Langmuir qm (mg/g) - 34.420 2.621 6.356 16.032bL - 0.006 0.811 0.175 0.105R2 - 0.904 0.944 0.938 0.979
Freundlich KF((mg/g)(L/mg)1'")
14.284 0.280 1.351 1.635 1.843
1/n 1.158 0.875 0.170 0.354 0.661R2 0.992 0.906 0.911 0.943 0.988
Langmuir- K (mg/g) - - 2.129 1.635 1.741Freundlich A - - 0.802 0.167 0.106
1/n - - 0.919 0.590 0.511R2 - - 0.937 0.945 0.987
- Do not fit
surface of the adsorbent by any of the oxidants mentioned above.
H2O2 + Fe2+ -> OH* + OH’ + Fe3+ (8)
Fe3+ + H2O2 -> Fe2+ + H++’ HO2 (9)
Cu2++’ HO2 -+ Cu+ + H+ + O2(g, (10)
The removal percentages of dye by each material in the adsorption-regeneration cycles in the presence and absence of sunlight are shown in Figure 9. According to the results, Mt-Fe-7 had the highest removal efficiencies of dye during the regeneration cycles (93-98%) in the presence of sunlight, whereas AC-N and Mt-Cu-7 had a similar behavior in the presence and absence of sunlight, and the removal of dye by Mt-KSF and AC-Cu- 2 decreased on increasing the number of cycles. The behavior of Mt-KSF could be attributed to both the dosage of hydrogen peroxide and amount of iron present in the natural clay which may be insufficient to oxidize the adsorbed dye.
When the adsorbents were regenerated in the presence of sunlight, the efficiencies of these materials through evaluated cycles were slightly higher, which could be attributed to the UV light playing a catalyzer
Adsorbent
| Cycle 0 « Cycle 1 z Cycle 2 ■ Cycle 3 » Cycle 4 |
Adsorbent[ ■< Cycled «Cycle 1 >Cycle2 «CycleS t Cycle4 |
Figure 9. Adsorption-regeneration cycles of adsorbents (a) in the presence and (b) absence of sunlight.
Perla Tatiana Almazán Sánchez 53
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 54
“Tratamientos avanzados para la remoción de un colorante de origen textil”
12 @ P.T. ALMAZÁN-SÁNCHEZ ET AL
Proposed oxidation mechanism of the adsorbed dye by the Fenton process
The regeneration of dye-saturated clay (Mt-Fe-7) may take place by oxidation of dye molecules. The degradation pathway of the dye Is shown In Figure 10. Step I describes the adsorption process; according to kinetic and Isotherms studies, the chemisorption mechanism is bounded. In step II the hydroperoxyl radical Is formed from hydrogen peroxide and Fe3+. Step III shows the reaction of the hydroperoxyl radical with the double bond of the structure of dye molecule to promote Its cleavage followed by oxidation of sulfonate groups to sulfate Ions (step IV) and formation of lH-lndollne-2,3- dlone (step V); then It Is oxidized to 2-(2-amlnophenyl)- 2-oxoacetlc acid (step VI); finally the probable oxidation products are oxalic, formic and acetic acid as well as sulfate and nitrate Ions (step VII) as It was proposed by Qu et al. [65] They suggested a mechanism of degradation of Indigo dye by O3 and "OH.
The Iron-modified clay was regenerated by the oxidation of dye, because the ferric Ions In the samples were reduced to ferrous Ions; this process was confirmed In the sorption-regeneration cycles.
ConclusionsThe removal of Indigo dye blue was achieved using unmodified and modified montmorlllonlte and activated carbon. Electrochemical modification Is an option to retain metallic Ions on adsorbents to Improve their adsorption capacities or adsorption-regeneration cycles. According to EDS analyses, the optimum pH to modify montmorillonite with Iron and copper was pH 7 and for activated carbon, pH 2. Mt-KSF, Mt-Fe-7 and Mt-Cu- 7 showed similar behaviors on the removal of dye at pH values from 2 to 10 with efficiencies above 95%. The efficiencies for Mt-Fe-2 and Mt-Cu-2 decreased as the pH values Increased. The removal efficiency of AC- Cu-2 was 93-100% at pH values from 4 to 10 while the removal behaviors for AC-N, AC-Fe-2, AC-Fe and AC-Cu were similar. Results suggest that the removal of dye from aqueous solutions takes place by chemisorption. Isotherm experimental data of Mt-Cu-7 were fitted to the Langmuir model whereas Mt-KSF, Mt-Fe-7, AC-N and AC-Cu-2 were adjusted to the Freundlich model. Indicating a heterogeneous surface and multilayer adsorption. The Iron and copper catalysts did not significantly Improve the adsorption process; however the removal efficiency In the regeneration cycles were Increased and maintained during four cycles. Mt-Fe-7 showed the best properties In adsorption-regeneration cycles by Fenton-llke processes.
Disclosure statementNo potential conflict of Interest was reported by the authors.
FundingWe acknowledge the financial support from CONACYT, project 219743 and scholarship Grant for PTAS No. 257364.
References[1] Lee JW, Choi SP, Thlruvenkatacharl R, Shim WG, Moon H.
Evaluation of the performance of adsorption and coagulation processes for the maximum removal of reactive dyes. Dyes Pigments. 2006;20:196-203.
[2] Garg VK, Kumar R, Gupta R. Removal of malachite green dye from aqueous solution by adsorption using agroindustry waste: a case study of Prosopls cineraria. Dyes Pigments. 2004;62:1-10.
[3] Amin NK. Removal of direct blue-106 dye from aqueous solution using new activated carbons developed from pomegranate peel: adsorption equilibrium and kinetics. J Hazard Mater. 2009;165:52-62.
[4] Lee CK, Low KS, Gan PY. Removal of some organic dyes by acid-treated spent bleaching earth. Environ Technol. 1999;20:99-104.
[5] Paplc S, Koprlvanac N, Metes A. Optimizing polymer- induced flocculation process to remove reactive dyes from wastewater. Environ Technol. 2000;21 (1 ):97—105.
[6] Slokar YM, Majcen Le Marechal A. Methods of decoloration of textile wastewaters. Dyes Pigments. 1998;37 (4):335-356.
[7] Chung KT, Stevens SE. Degradation azo dyes by environmental microorganisms and helminths. Environ Toxicol Chem. 1993;12:2121-2132.
[8] Cañizares P, Martínez F, Jiménez C, Lobato J, Rodrigo MA. Coagulation and electrocoagulation of wastes polluted with dyes. Environ Sci Technol. 2006;40(20):6418-6424.
[9] Mesqulta I, Matos LC, Duarte E, Maldonado-Hódar FJ, Mendes A, Madeira LM. Treatment of azo dye-containing wastewater by a Fenton-llke process In a continuous packed-bed reactor filled with activated carbon. J Hazard Mater. 2012,-237-238:30-37.
[10] Wong Y, Yu J. Laccase-catalyzed decolorlzatlon of synthetic dyes. Water Res. 1999;33:3512-3520.
[11] Cameselle C, Pazos M, Sanromán MA. Selection of an electrolyte to enhance the electrochemical decolourlsa- tlon of Indigo. Optimisation and scale-up. Chemosphere. 2005;60:1080-1086.
[12] Sanromán MA, Pazos M, Rlcart MT, Cameselle C. Decolourisatlon of textile Indigo dye by DC electric current. Eng Geol. 2005;77:253-261.
[13] McMullan G, Meehan C, Conneely A, Kirby N, Robinson T, Nlgam P, Banat I, Marchant R, Smyth W. Microbial deco- lourlsatlon and degradation of textile dyes. Appl Microbiol Blot. 2001;56:81-87.
[14] Khellfi E, Gannoun H, Touhaml Y, Bouallagul H, Hamdl M. Aerobic decolourlzatlon of the Indigo dye-containing textile wastewater using continuous combined blo- reactors. J Hazard Mater. 2008,-152:683-689.
Perla Tatiana Almazán Sánchez 55
“Tratamientos avanzados para la remoción de un colorante de origen textil”
[15] Manu B, Chaudhari S. Decolorization of indigo and azo dyes in semicontinuous reactors with long hydraulic retention time. Process Blochem. 2003;38:1213-1221.
[16] Balan DSL, Monteiro RTR. Decolorization of textile indigo dye by ligninolytic fungi. J. Biotechnol. 2001;89:141-145.
[17] Alaoui 0, Nguyen Q, Rhlalou T. Preparation and characterization of a new TiO2/SiO2 composite catalyst for photoca- talytlc degradation of indigo carmin. Environ Chem Lett.
2009;7:175-181.[18] Albuquerque LF, Salgueiro AA, Melo JLdS, Chiavone-Filho
O. Coagulation of Indigo blue present In dyeing wastewater using a residual bittern. Sep Purlf Technol. 2013;104:246-249.
[19] Abbasi M, Asl NR. Sonochemical degradation of Basic Blue 41 dye assisted by nanoTIO2 and H2O2. J Hazard Mater. 2008;153:942-947.
[20] Wu CH. Decolorization of C.l. reactive red 2 in O3, Fentonlike and O3/Fenton-like hybrid systems. Dyes Pigments. 2008;77:24-30.
[21] Zaghbani N, Hafiane A, Dhahbi M. Removal of Safranin T from wastewater using micellar enhanced ultrafiltration. Desalination. 2008;222:348-356.
[22] Amar NB, Kechaou N, Palmerl J, Deratani A, Sghaier A. Comparison of tertiary treatment by nanofiltration and reverse osmosis for water reuse in denim textile Industry. J Hazard Mater. 2009;170:111-117.
[23] Zhu MX, Lee L, Wang HH, Wang Z. Removal of an anionic dye by adsorption/preclpltation processes using alkaline white mud. J Hazard Mater. 2007;149:735-741.
[24] Tan BH, Teng TT, Omar AKM. Removal of dyes and Industrial dye wastes by magnesium chloride. Water Res. 2000;34:597-601.
[25] Vedrenne M, Vasquez-Medrano R, Prato-Garcia D, Frontana-Uribe BA, Hernandez-Esparza M, de Andres JM. A ferrous oxalate mediated photo-Fenton system: toward an increased biodegradability of indigo dyed wastewaters. J Hazard Mater. 2012;243:292-301.
[26] Turhan K, Turgut Z. Decolorization of direct dye in textile wastewater by ozonization In a semi-batch bubble column reactor. Desalination. 2009;242:256-263.
[27] Zainal Z, Hui LK, Hussein MZ, Taufiq-Yap YH, Abdullah AH, Ramil I. Removal of dyes using immobilized titanium dioxide illuminated by fluorescent lamps. J Hazard Mater. 2005;125:113-120.
[28] Butrón E, Juárez ME, Solis M, Teutli M, González I, Nava JL. Electrochemical incineration of indigo textile dye in filter- press-type FM01-LC electrochemical cell using BDD electrodes. Electrochlm Acta. 2007;52:6888-6894.
[29] Ammar S, Abdelhedl R, Flox C, Arlas C, Brillas E. Electrochemical degradation of the dye indigo carmine at boron-doped diamond anode for wastewaters remediation. Environ Chem Lett. 2006;4:229-233.
[30] Gupta VK, Suhas. Application of low-cost adsorbents for dye removal - A review. J Environ Manage. 2009;90:2313- 2342.
[31] Ahmad AA, Hameed BH. Reduction of COD and color of dyeing effluent from a cotton textile mill by adsorption onto bamboo-based activated carbon. J Hazard Mater. 2009;172:1538-1543.
[32] Lakshmi UR, Srivastava VC, Mall ID, Lataye DH. Rice husk ash as an effective adsorbent: evaluation of adsorptive
ENVIRONMENTAL TECHNOLOGY (*) 13
characteristics for indigo carmine dye. J Environ Manage. 2009;90:710-720.
[33] Gutiérrez-Segura E, Solache-Ríos M, Colin-Cruz A. Sorption of indigo carmine by a Fe-zeolltlc tuff and carbonaceous material from pyrolyzed sewage sludge. J Hazard Mater.
2009;170:1227-1235.[34] Othman I, Mohamed RM, Ibrahim IA, Mohamed MM.
Synthesis and modification of ZSM-5 with manganese and lanthanum and their effects on decolorization of indigo carmine dye. Appi Catal A-Gen. 2006;299:95-102.
[35] Shen D, Fan J, Zhou W, Gao B, Yue Q, Kang Q. Adsorption kinetics and isotherm of anionic dyes onto organo-bento- nite from single and multisolute systems. J Hazard Mater.
2009;172:99-107.[36] DíazGómez-Treviño AP, Martinez-Miranda V, Solache-Rios
M. Removal of remazol yellow from aqueous solutions by unmodified and stabilized iron modified clay. Appi Clay Scl. 2013;80-81:219-225.
[37] Wang S, Peng Y. Natural zeolites as effective adsorbents in water and wastewater treatment. Chem Eng J. 2010;156:11-24.
[38] Kusic H, Koprivanac N, Selanec I. Fe-exchanged zeolite as the effective heterogeneous Fenton-type catalyst for the organic pollutant minimization: UV irradiation assistance. Chemosphere. 2006;65:65-73.
[39] Herney-Ramirez J, Vicente MA, Madeira LM. Heterogeneous photo-Fenton oxidation with pillared clay-based catalysts for wastewater treatment a review. Appi Catal B-Envlron. 2010;98:10-26.
[40] Trujillo-Reyes J, Sánchez-Mendleta V, Colin-Cruz A, Morales- Luckle R. Removal of indigo blue in aqueous solution using Fe/Cu nanoparticles and C/Fe-Cu nanoalloy composites. Water Air Soil Pollut. 2010;207:307-317.
[41] Trujillo-Reyes J, Solache-Ríos M, Vilchis-Nestor A, Sánchez- Mendieta V, Colin-Cruz A. Fe-Ni nanostructures and C/Fe- Ni composites as adsorbents for the removal of a textile dye from aqueous solution. Water Air Soil Pollut. 2012;223:1331-1341.
[42] Teutli-Sequeira A, Martinez-Miranda V, Solache-Ríos M, Linares-Hernández I. Aluminum and lanthanum effects in natural materials on the adsorption of fluoride ions. J Fluorine Chem. 2013;148:6-13.
[43] Vázquez Mejía G, Martinez-Miranda V, Fall C, Linares- Hernández I, Solache-Ríos M. Comparison of Fe-AI- modified natural materials by an electrochemical method and chemical precipitation for the adsorption of F- and As(V). Environ Technol. 2015. doi:10.1080/ 09593330.2015.1074724.
[44] Almazán-Sánchez P, Castañeda-Juárez M, Martinez- Miranda V, Solache-Ríos M, Lugo-Lugo V, Linares- Hernández I. Behavior of TOC and color in the presence of iron-modified activated carbon in Methyl Methacrylate wastewater In batch and column systems. Water Air Soil Poll. 2015;226:1-13.
[45] Ortega-Gómez E, Ballesteros Martín MM, Carratalá A, Fernández Ibañez P, Sánchez Pérez JA, Pulgarin C. Principal parameters affecting virus inactivation by the solar photo-Fenton process at neutral pH and pM concentrations of H202 and Fe2+/3+. Appi Catal B-Environ.
2015;174-175:395-402.[46] Cotton FA, Wilkinson G. Química Inorgánica Avanzada:
Química de los elementos de transición [Advanced
Perla Tatiana Almazán Sánchez 56
“Tratamientos avanzados para la remoción de un colorante de origen textil”
14 @ P.T. ALMAZÁN-SÁNCHEZ ETAL.
Inorganic Chemistry; The chemistry of the transition elements], México: Llmusa; 2006.
[47] Gutlérrez-Segura E, Solache-Ríos M, Fall C, Colin-Cruz A. Influence of the pH on distribution of denim blue In water Fe-Zeolltlc tuff system. Sep Sci Technol. 2012;47:723-728.
[48] Ho YS, McKay G. Sorption of dye from aqueous solution by peat. Chem Eng J. 1998;70:115-124.
[49] Ho Y-S. Review of second-order models for adsorption systems. J Hazard Mater. 2006;136:681-689.
[50] Lagergren S. About the theory of so-called adsorption of soluble substances. Kungllga Svenska Vetenskapsakademlens. Handlingar. 1898;24:1-39.
[51] Nekouel F, Nekouel S, Tyagl I, Gupta VK. Kinetic, thermodynamic and isotherm studies for acid blue 129 removal from liquids using copper oxide nanoparticle-modlfied activated carbon as a novel adsorbent. J Mol Liq. 2015;201:124-133.
[52] Ho YS, McKay G. A comparison of chemisorption kinetic models applied to pollutant removal on various sorbents. Process Saf Environ. 1998;76:332-340.
[53] Cottet L, Almeida CAP, Naidek N, Víante MF, Lopes MC, Debacher NA. Adsorption characteristics of montmorillonite clay modified with Iron oxide with respect to methylene blue in aqueous media. Appl Clay Sci. 2014;95:25-31.
[54] Aharonl C, Tompkins FC. Kinetics of adsorption and desorption and the Elovich equation. In Eley DD, Pines H, Welsz PB, editors. Advances In catalysis. New York: Academic Press; 1970, p. 1 -49.
[55] Wu FC, Tseng RL, Juang R-S. Characteristics of Elovich equation used for the analysis of adsorption kinetics in dye-chltosan systems. Chem Eng J. 2009;150:366-373.
[56] Belaid KD, Kacha S, Kameche M, Derriche Z. Adsorption kinetics of some textile dyes onto granular activated carbon. J Environ Chem Eng. 2013;1:496-503.
[57] Langmuir I. The constitution and fundamental properties of solids and liquids. Part I. Solids. J Am Chem Soc. 1916;38:2221-2295.
[58] Ho YS, Chiang TH, Hsueh Y-M. Removal of basic dye from aqueous solution using tree fern as a biosorbent. Process Biochem. 2005;40:119-124.
[59] Chaari I, Feki M, Medhioub M, Bouzld J, Fakhfakh E, Jamoussi F. Adsorption of a textile dye 'Indanthrene Blue RS (C.l. Vat Blue 4)' from aqueous solutions onto smectlte-rlch clayey rock. J Hazard Mater. 2009,-172:16231628.
[60] Freundlich HMF. Over the adsorption In solution. J Phys Chem. 1906;57:385-470.
[61] Ho YS, Ofomaja AE. Blosorptlon thermodynamics of cadmium on coconut copra meal as blosorbent. Biochem Eng J. 2006;30:117-123.
[62] Mahmoodi NM, Salehi R, Arami M. Binary system dye removal from colored textile wastewater using activated carbon: kinetic and isotherm studies. Desalination. 2011;272:187-195.
[63] Jeppu GP, Clement TP. A modified Langmuir-Freundlich isotherm model for simulating pH-dependent adsorption effects. J Contam Hydrol. 2012:129-130:46-53.
[64] Legrini O, Oliveros E, Braun AM. Photochemical processes for water treatment. Chem Rev. 1993;93:671-698.
[65] Qu R, Xu B, Meng L, Wang L, Wang Z. Ozonation of Indigo enhanced by carboxylated carbon nanotubes: performance optimization, degradation products, reaction mechanism and toxicity evaluation. Water Res. 2015;68:316-327.
Perla Tatiana Almazán Sánchez 57
“Tratamientos avanzados para la remoción de un colorante de origen textil”
5.2 Segundo artículo de investigación
En esta sección se muestra el segundo artículo de investigación realizado aplicando
el proceso de adsorción en batch y columna al agua residual proveniente de una lavandería
de acabados de prendas de mezclilla.
Textile wastewater treatment using iron modified clay and copper modified carbon
in batch and columns systems
Perla Tatiana Almazán-Sáncheza,b, Ivonne Linares-Hernándezb, Marcos J. Solache-
Ríosa*, Verónica Martínez-Mirandab,
Revista: Water Air and Soil Pollution
Status: Publicado
DOI: 10.1007/s11270-016-2801-7
Perla Tatiana Almazán Sánchez 58
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016)227:100
DOI 10.1007/sll270-016-2801-7 & CrossMark
Textile Wastewater Treatment Using Iron-Modified Clay and Copper-Modified Carbon in Batch and Column Systems
Perla Tatiana Almazán-Sánchez •Ivonne Linares-Hernández • Marcos J. Solache-Ríos • Verónica Martinez-Miranda
Received: 12 November 2015 / Accepted: 29 February 2016 © Springer International Publishing Switzerland 2016
Abstract Textile wastewater was treated by adsorption in batch and column systems using electrochemically modified montmorillonite clay and activated carbon. Textile wastewater was obtained from a denim manufacturing process; according to the characterization of wastewater, non-biodegradable organic matter was found and it limits the application of biological treatments, and then an alternative method was evaluated. The adsorption process was performed with natural and modified materials; iron-modified montmorillonite was prepared at pH 7 using iron electrodes and activated carbon was treated with copper electrodes at pH 2, and 10-12 % of iron and copper respectively were found in the modified materials. Adsorption kinetics and isotherms of chemical oxygen demand (COD), color, and total organic carbon (TOC) were evaluated; the adsorption capacities for color were 50, 37, and 44 U PtCo/g for natural clay, activated carbon, and iron-modified clay, respectively. Adsorption kinetics of COD, color, and TOC data were best adjusted to Elovich model and isotherms data to Freundlich model, indicating
P. T. Almazán-Sánchez • M. J. Solache-Ríos (El)Departamento de Química, Instituto Nacional de Investigaciones Nucleares (ININ), Carretera México-Toluca S/N, La Marquesa, C.P. 52750 Ocoyoacac, Estado de México, Mexico e-mail: marcos.solache@inin.gob.mx
P. T. Almazán-Sánchez • I. Linares-Hernández •V. Martinez-MirandaCentro Interamericano de Recursos del Agua (CIRA), Facultad de Ingeniería, Unidad San Cayetano, Universidad Autónoma del Estado de México, Km. 14.5, carretera Toluca-Atlacomulco, C.P. 50200 Toluca, Estado de México, Mexico
Published online: 08 March 2016
chemisorption on heterogeneous materials. The regeneration of materials was performed in the presence and absence of hydrogen peroxide. Continuous systems were evaluated for color and TOC. Fe-modified clay was the best adsorbent, and data were best adjusted to Thomas and Yoon-Nelson models.
Keywords Montmorillonite ■ Activated carbon ■ Electrochemical modification • Fixed bed column
1 Introduction
Textile industry plays an important role in the world economy; the discharge of textile effluents to natural water bodies causes alterations in aquatic biological activities (Amin 2009) because dyes could be mutagenic and carcinogenic (Kadirvelu et al. 2003). This industry is one of the most polluting because of the large amounts of water, dyes, and chemical compounds used in the processes. Textile wastewater contains color and organic compounds with complex structures that are discharged in sewerages and surface waters (Butrón et al. 2007). Textile dyes are usually transformed to toxic aromatic amines, they absorb and reflect sunlight, avoiding the photosynthesis of aquatic plants, and they exhibit recalcitrant properties (Cañizares et al. 2006; Kadirvelu et al. 2003; Mesquita et al. 2012).
Textile industry is the fourth largest manufacture activity in Mexico; furthermore, it is one of the most important industries, because Mexico is the fourth
<£) Springer
Perla Tatiana Almazán Sánchez 59
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 2 of 14 Water Air Soil Pollut (2016) 227:100
largest supplier of jeans to US market. This activity has resulted in pollution of water bodies.
Recently, some processes have been applied to remove dyes from wastewater, specifically by using biological treatments (Firmino et al. 2010; Franca et al. 2015; Khelifi et al. 2008), coagulation/flocculation (Albuquerque et al. 2013), electrochemical treatments (Sanromán et al. 2005) as Fenton (Hayat et al. 2015), solar photo-Fenton (Doumic et al. 2015; Soares et al. 2015), ozonation (Polat et al. 2015), adsorption using different materials as activated carbon (Belaid et al. 2013), clinoptilolite (Gutiérrez-Segura et al. 2009; Kehinde and Aziz 2015), and photocatalysis (Cardoso etal. 2015; Lee etal. 2015).
Adsorption process had been widely used in the removal of organic matter like dyes; however, it is important to use materials that are easily available and regenerated, and for this reason, sometimes the adsorbents are modified to improve their adsorption and regeneration properties. Some studies have reported the adsorption and degradation of organic contaminants in aqueous solutions by using iron-modified aluminosilicates and hydrogen peroxide (Torres-Pérez et al. 2008).
The aim of this paper was to prepare copper- and iron-modified aluminosilicates, in order to treat wastewater from the textile industry in batch and column systems. Regeneration of the materials was performed by adding hydrogen peroxide to the systems.
2 Material and Methods
2.1 Wastewater Sampling
A textile wastewater sample was obtained from the rinse vat of a denim textile manufacturing process, where the denim clothes only receive a finished treatment using products, such as liquid detergents, fabric softeners, sea salt, and pumice stone. The sample was collected in a plastic container and subsequently characterized.
2.1.1 Wastewater Characterization
Physicochemical characterization was done to a textile wastewater sample according to parameters enlisted in Table 1. Chemical oxygen demand (COD), biological oxygen demand (BOD), total organic carbon (TOC), hardness, alkalinity, acidity, methylene blue active
Springer
Table 1 Physicochemical characterization of textile wastewater
Parameter Units Value
pH - 6.84
Alkalinity mg/L CaCO3 83.25
HCO3 mg/L 101.5
CO32’ mg/L 0.035
Acidity mg/L CaCO3 20.75
COD mg/L O2 344.00
BOD, mg/L O2 91.91
N-NH3 mg/L -
Color U PtCo 330
TOC mg/L 84.92
SO42' mg/L 227.06
PO? mg/L 287.08
N-NOj mg/L 1.90
n-no2 mg/L 0.05
Turbidity NTU 104.66
Conductivity pS/cm 471.30
Cl mg/L 338.19
Hardness mg/L CaCO3 119.17
MBAS mg/L 0.13
Na mg/L 44.99
K mg/L 3.08
Mg mg/L 4.39
Ca mg/L 5.65
Si mg/L 5.60
Mn mg/L 1.99
Fe mg/L 0.343
Non-detectable
substances, sulfates, chlorides, and metals were determined by standard procedures (AWWA).
2.2 Electrochemical Modification of Adsorbents
Adsorbents were modified using an electrochemical batch cell with monopolar electrode systems of iron or copper with dimensions of 0.040 m long and 0.024 m wide. The clay used was a powder montmorillonite KSF (Mt-KSF) from Fluka Chemika and granular activated carbon (AC-N) from Clarimex. Ten grams of material was put in an electrochemical cell with 0.08 L of deionized water and a current intensity of 0.5 A. Iron electrodes were used to modify the montmorillonite (Mt-Fe- 7) at pH of 7 for 130 min, whereas activated carbon was modified with copper electrodes (AC-Cu-2) at pH 2 for
Perla Tatiana Almazán Sánchez 60
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016) 227:100 Page 3 of 14 100
72 min. After modification, the materials were washed several times with deionized water and dried at 90 °C for 18 h.
2.3 Characterization of Materials
Natural and modified materials were characterized by scanning electronic microscopy (SEM) and electron X- ray dispersive spectroscopy (EDS) using a Jeol JSM- 661OLV microscope to determine the elemental composition and the morphology.
Clay samples were analyzed by X-ray diffraction using a Siemens D500 diffractometer coupled with a copper anode X-ray tube. Specific surface areas were determined by Brunauer-Emmett-Teller (BET) method using a Micromeritics equipment model Gemini 2360. The samples were heated at 200 °C for 2 h before the analysis.
2.4 Adsorption Treatment
2.4.1 Adsorption Kinetics
The adsorption kinetics were carried out with 0.150 g of natural and modified material (Mt-KSF, Mt-Fe-7, AC-N, AC-Cu-2) and 0.015 L of textile wastewater (pH 6.8) with contact times of 5, 15, 30, 60 180, 300, 420, 1440, 2880, and 4320 min. The samples were centrifuged and filtered with Whatman 42 filter and color, TOC, and COD parameters were determined in the solutions.
2.4.2 Adsorption Isotherms
The adsorption isotherms were performance in two ways: (a) varying the adsorbent dosage (0.020, 0.050,O. 080, 0.100, 0.120, 0.150, 0.180, 0.200, 0.250, and 0.300 g of each material) and (b) adsorbent dosage constant (0.150 g) and dilutions of wastewater. The volume used was 0.015 L and contact time of 72 h, then the samples were centrifuged and filtered. For the first case (a) color, TOC, and COD were determined in the filtered solutions and for the second case, color was evaluated.
2.4.3 Column Systems
The evaluation of column systems was done with AC- N, Mt-KSF, and Mt-Fe-7. For AC-N, the masses used in columns were 3, 5, and 7 g with bed heights of 3.3, 5.4,
and 8.3 cm respectively, and descendent flow of 1 mL/ min was used. For clays sample, the masses were 1, 2, and 3 g with bed heights of 0.9, 1.7, and 2.4 cm for Mt- KSF and 1.1, 2.4, and 2.8 cm for Mt-Fe-7 and using an ascendant flow of 1 mL/min. The column used was of glass with an internal diameter of 1.50 cm. Data of color and TOC were analyzed using Thomas, Yoon and Nelson, and Bohart-Adams models.
2.5 Regeneration Cycles
Adsorbents used in the treatment of textile wastewater were regenerated and reused. The regeneration process was performed in different ways using only deionized waster, and hydrogen peroxide solutions in the presence and absence of sunlight. 0.150 g of each adsorbent and 0.015 L of wastewater were put in contact for 72 h, then the mixtures were centrifuged and filtered, and color, TOC, and COD parameters were analyzed in the solutions. Later, 1.5 mL of deionized water or a 1:1 (%F7F) H2O2 solution was added to the adsorbent and left for4.5 h; in the last case, the mixtures were left in the presence and absence of sunlight. The adsorbents were washed with deionized water and dried at 90 °C for 3 h. Four adsorption-regeneration cycles were perfonned.
3 Results and Discussion
3.1 Characterization of Natural and Modified Materials
The materials were characterized by scanning electron microscopy. According to EDS analysis, the elements identified in the Mt-KSF sample were carbon, oxygen, magnesium, aluminum, silicon, sulfur, potassium, calcium, and iron, whereas in iron-modified clay, the same elements were found and the content of Fe increased from 5.99 to 15.66 %. Carbon, oxygen, and silicon were identified in the activated carbon sample, and the percentage of copper was 12.02 % in copper-modified carbon. These results showed that the metals were fixed in materials. According to the treatments of samples, the metals in the adsorbents should be present as ferric and cupric ions.
Mt-KSF and Mt-Fe-7 were analyzed by X-ray diffraction. The diffractograms obtained were compared with the Joint Committee on Powder Diffraction Standards lists (JCPDS), and the peaks of the samples corresponded to montmorillonite (JCPDS 00-003-
Springer
Perla Tatiana Almazán Sánchez 61
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 4 of 14 Water Air Soil Pollut (2016) 227:100
0010), muscovite (JCPDS 00-034-0175), and quartz (JCPDS 01-087-2096). The differences found in the diffractogram of unmodified and modified clays were the intensity of the peaks; the results show that there was not any important change in the structure of clay after modification.
The specific surface areas analysis showed values of 5.14, 131.3, and 654.85 m2/g for Mt-KSF, Mt-Fe-7, and AC-Cu-2, respectively. After electrochemical modification with iron, an important increment of surface area was observed. It could be attributed to presence of iron fixed during modification; a similar behavior was observed by DíazGómez-Treviño et al. (2013), in a clay modified with FeCl3.
3.2 Wastewater Characterization
Table 1 shows the physicochemical parameters of textile wastewater. The pH value was nearly neutral; the concentrations of anionic ions as sulfate, phosphate, and chloride are high and they play an important role in the adsorption process. The biodegradability index (r) of wastewater is BOD5/COD ratio; it relates the biological oxygen demand and the chemical oxygen demand, and the biodegradability index of the textile wastewater is 0.27. According to Metcalf and Eddy (2003), r values lower than 0.3 indicate low biodegradability and the organic matter in the samples could be toxic. These parameters limit the application of biological processes; then it is so important to minimize the adverse impacts to environment by implementing a process to treat this wastewater because it is discharged to superficial water bodies. Another important parameter is the presence of methylene blue active substances (MBAS). Its value is low and indicates that detergents used in the textile industry are not anionic. Phosphorous concentration (287.08 mg/L PO43 ) is high, exceeding the permissible limit established by Mexican regulations, and its presence in water bodies induces the eutrophication process.
3.3 Kinetics Adsorption
Kinetic adsorption provides information about the time to reach the equilibrium, the adsorption rate, and the possible adsorption mechanism involved. There are models in the literature to analyze the kinetics adsorption behavior; Lagergren or pseudo-first-order model (Eq. 1) (Lagergren 1898) indicates physisorption process. Pseudo-second-order (Ho 2006) (Eq. 2) and
Springer
Elovich models (Aharoni and Tompkins 1970) (Eq. 3) indicate chemisorption process:
^ = 9e(l-Z'') (l)
q, = t/(yiK-2qe2(tlqe)) V)
q, = \/bln(\ + (abt)) (3)
where q, is the adsorption capacity (mg/g) at time t (min), qe is the adsorption capacity at equilibrium, K, (1/min) and K2 (g/mg min) are the pseudo-first- and pseudo-second-order constants, a (mg/g min) is the initial adsorption rate, and b is the desorption constant (mg/g).
Figure 1 shows the kinetics adsorption of COD, color, and TOC by unmodified clay from textile wastewater. The adsorption of COD was similar in the time evaluated, although the standard deviations were high up to 24 h, with an adsorption capacity of about 8 mg/g up to 48 h of contact time and a slight desorption was observed at the end of the process (72 h) (Fig. 1 a). Color adsorption was constant from the beginning of the process (5 min of contact) with an adsorption capacity of 50 U PtCo/g (Fig. lb). The kinetic adsorption of TOC (Fig. lc) shows a maximum adsorption at 30 min of contact time, after a desorption process occurred. Natural clay (M-KFS) was efficient to remove the color from textile wastewater. However, other organic matter present in the sample was not absorbed by the material. This behavior could be attributed to the properties of clays because they remove mainly cationic species, and the textile wastewater evaluated in this work could contain organic compounds (detergents for example) as nonylphenols, and probably the presence of these organic compounds are responsible for similar adsorption behaviors found for COD and TOC.
The removal efficiencies for COD, color, and TOC using unmodified clay were 32.4, 90.3, and 18.6 %, respectively, at the end of the process.
Figures 2, 3, and 4 show the kinetics adsorption of COD, color, and TOC respectively by Mt-Fe-7, AC-N, and AC-Cu-2. Natural carbon (AC-N) presents the highest adsorption capacity of COD (12.1 mg/g), then Mt-Fe-7, and AC-Cu-2, and the equilibrium time was reached in 72 h for the three adsorbents. According to Table 2, the adsorption data of COD by Mt-Fe-7, AC-N,
Perla Tatiana Almazán Sánchez 62
Tratamientos avanzados para la remoción de un colorante de origen textil”
and AC-Cu-2 were best adjusted to Elovich model, indicating that the possible mechanism is chemisorption. The removal efficiencies of COD at 72 h were 54.9, 73.3, and 53.3 % for Mt-Fe-7, AC-N, and AC- Cu-2, respectively, and the adsorption capacities were 9.2, 12.1, and 7.8 mg/g, respectively.
Color was best adsorbed by Mt-Fe-7 (Fig. 3). The equilibrium time was reached in about 48 h for all adsorbents, and the adsorption capacities were 43.9, 37.5, and 11.5 U PtCo/g for Mt-Fe-7, AC-N, and AC- Cu-2, respectively. According to Table 1, the data were best adjusted to Elovich model. The removal efficiencies of color were 65.2, 72.1, and 37.5 % for Mt-Fe-7, AC-N, and AC-Cu-2, respectively.
The kinetic adsorption behavior of TOC is shown in Fig. 4, The equilibrium time was reached in about 48 h, and before the equilibrium was reached, the highest adsorption was observed for Mt-Fe-7. TOC data were best adjusted to Elovich model. At the end of contact time, the removal efficiencies of TOC were 46.9, 63.4, and 46.1 % for Mt-Fe-7, AC-N, and AC-Cu-2, respectively, and the adsorption capacities were 2.629, 3.002, and 2.086 mg/g, respectively.
According to experimental data, AC-Cu-2 showed the lowest efficiencies for the removal of COD, color, and TOC, but it had the highest specific surface area. This behavior could be attributed to the weak affinity of copper for organic matter present in the textile wastewater. Although transition metals have the capacities to form complexes with organic matter, in this case it was not observed, probably due to the presence of inorganic matter because wastewater contains high concentrations of anions as phosphate, sulfates, and chlorides.
Oluwakemi and Abdul (2015) treated textile wastewater using clinoptilolite. Their data were best adjusted to pseudo-second-order model, with adsorption capacities of 98.04 U PtCo/g for color and 48.08 mg/g for COD. The initial concentrations were 2870-3000 U PtCo and 2600-3000 COD, and the removal efficiencies were 89 and 79 % respectively. These adsorption capacities and removal efficiencies are higher than the results found in this work; however, their results were obtained in acidic conditions (pH 2.0-3.0), which may cause problems of corrosion or alteration of aquatic life
■ Mt-Fe-7 A AC-N • AC-Cu-2
Fig. 2 Adsorption kinetic of COD in wastewater using Mt-Fe-7, AC-N, and AC-Cu-2
0 f---------- i------------ 1------------ i------------ 1—0 1000 2000 3000 4000
t (min)
■ Mt-Fe-7 A AC-N • AC-Cu-2
Fig. 3 Adsorption kinetic of color from wastewater by using Mt- Fe-7, AC-N, and AC-Cu-2
Perla Tatiana Almazán Sánchez 63
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 6 of 14 Water Air Soil Pollut (2016) 227:100
4.5 -i 4.0 -
o.o a------------------- 1------------ 1------------ 1------------ 1------0 1000 2000 3000
l (min)4000
■ Mt-Fe-7 A AC-N • AC-Cu-2
Fig. 4 Adsorption kinetic of TOC in wastewater using Mt-Fe-7, AC-N, and AC-Cu-2
if treated water were reused or discharged in water bodies. In this study, the kinetic experiments were done at pH of wastewater (6.8), and after adsorption, the pH of treated water was 2.8 for Mt-KSF and 7.3-7.5 for Mt-Fe-7, AC-N, and AC-Cu-2. This behavior could be attributed to the zero-point charge of the materials; in the case of Mt-KSF, the pH 2 was observed immediately after the wastewater was in contact with the material. It is probable that the removal efficiencies are higher at this pH and it could be attributed to the presence of organic neutral species in these pH conditions.
3.4 Adsorption Isotherms
Adsorption isotherms were evaluated in two ways: first, the adsorbent dosage was varied and second, textile wastewater was diluted. The data obtained were treated using Freundlich and Langmuir isotherm models.
Langmuir isothenn model is used to describe the adsorption in liquid-solid phase (Langmuir 1918) and it is represented by Eq. 4:
<7nACc1 + btCc
(4)
where qe is the adsorption capacity at equilibrium (mg/g); Ce is the concentration of adsorbate at equilibrium (mg/ L), bL is the Langmuir constant; and qm is the amount of adsorbate required to complete a monolayer (mg/g).
Freundlich isotherm is an empirical model based on an exponential relationship and it is applicable to heterogeneous surfaces (Freundlich 1906). This model is expressed by Eq. 5:
?e=/fFCe'A (5)
where qe is the adsorption capacity at equilibrium (mg/g); Ce is the concentration of adsorbate at equilibrium (mg/L), Xp ((mg/g)(L/mg)l/n), and 1/n are an empirical constants.
Tabic 2 Kinetic adsorption parameters of COD, color, and TOC applying pseudo-first-, pseudo-second-order, and Elovich models
Pseudo-first order Pseudo-second order Elovich
COD
K,(1/min)
9e(mg/g)
R2 k2(g/mg min) (mg/g)
R2 a(mg/g min)
b(mg/g)
/F
Mt-Fe-7 0.038 7.24 0.55 6E-03 7.82 0.67 3.46 1.07 0.89
AC-N 6E-03 10.67 0.63 8.3E-04 11.29 0.69 0.79 0.67 0.76
AC-Cu-2 1.0E-03 7.94 0.88 1.4E-04 9.22 0.92 0.02 0.46 0.95
Color
A) 9e R2 <?<■ R2 a b A2
Mt-Fe-7(1/min)0.022
(U Pt-Co/g) 33.88 0.71
(g/U Pt-Co min) 6.5E-04
(U Pt-Co/g) 37.24 0.81
(U Pt-Co/g min) 6.69
(U Pt-Co/g) 0.21 0.91
AC-N 5E-03 35.19 0.73 2.8E-04 35.86 0.82 2.06 0.19 0.95
AC-Cu-2 IE-03 16.74 0.80 5.5E-05 20.63 0.83 0.03 0.19 0.85
TOC
K, 9e R2 k2 ?<• R2 a b /F
M-Fe(1/min)0.15
(mg/g)2.48 0.65
(g/mg min)0.07
(mg/g)2.63 0.73
(mg/g min)44.05
(mg/g)4.48 0.85
CA-N 6E-03 2.83 0.80 3E-O3 3.00 0.88 0.09 2.05 0.94
CA-Cu 1.1E-02 1.8971 0.87 6.4E-03 2.09 0.93 0.09 3.07 0.95
Perla Tatiana Almazán Sánchez 64
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016) 227:100
Figure 5 shows the plot of qc vs. adsorbent dosage. The dosage of adsorbent increases as the adsorption capacities decrease. In general, when the mass is 0.20 g or more, the adsorption of color and COD are similar for all adsorbents. The same behavior was observed for TOC with Mt-Fe-7, AC-N, and AC- Cu-2; but with Mt-KSF, the values of <ye. were similar from 0.01 to 0.3 g.
The adsorption of TOC and COD from diluted textile wastewater had the same behavior, and the correlation coefficients were lower than 0.50 for both. Color isotherms were adjusted to both Langmuir and Freundlich models. Figure 6 shows the isotherms and Table 3 shows the parameters. In general, the data were adjusted to both models with correlation coefficients higher than 0.94. However AC-N showed correlation coefficient values lower than 0.6, and this behavior could be attributed to the presence of materials that were removed in the other materials when it was modified. According to the origin of the adsorbents, one would expect that they would be heterogeneous materials and therefore the Freundlich model should be considered in these systems.
3.5 Adsorption-Regeneration Cycles
Adsorption-regeneration cycles were evaluated in order to determine if the adsorbents could be reused. When an
Page 7 of 14 100
adsorption process is chosen to treat water, different factors should be considered, mainly the properties of adsorbent, its availability, cost, etc., and the regeneration is an important parameter because it determines the adsorbent cost.
Figures 7 and 8 show the efficiencies for the removal of COD, color, and TOC from textile wastewater through four regeneration cycles using hydrogen peroxide in the presence and absence of sunlight. The hydrogen peroxide is an oxidant compound with an oxidation potential of 1.78 V; this reagent forms hydroxyl radicals which are strong oxidants with an oxidation potential of 2.80 V, and their formation can be catalyzed by ferrous or copper ions (Fenton process) (Eq. 6) or UV radiation (Eq. 8). Another process may take place as Fenton-like, where Fe ’+ ions catalyze the formation of hydroperoxy 1 radicals (1.70 V) (Eq. 7); hydroxyl and hydroperoxyl radicals promote the oxidation of organic matter (OM) (Eq. 9) (Azmi et al. 2014):
Fe2+ + H2O2->Fe3+ + OH" + -OH (6)
Fe3++ H2O2—>Fe2++ HO2« + H+ (7)
H2O2 + Av—>2*OH (8)
DM 4- *OH or HO2* >OMpari¡auy oxidized *OMln¡ncra|j¿cc|(CO2 + salts + H2O) (9)
Perla Tatiana Almazán Sánchez 65
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 8 of 14 Water Air Soil Pollut (2016)227:100
0 50 100 150 200
C„ (V Pt-Co)
Fig. 6 Adsorption isotherms of color using of (♦) Mt-KSF, (■) Mt-Fe-7, (▲) AC-N, and (•) AC-Cu-2
and absence of sunlight. AC-Cu-2 material showed the lowest efficiency for the removal of parameters evaluated. A similar removal behavior was observed for Mt-Fe-7 and AC-N, indicating the regeneration of both materials, and the removal of color decreases using Mt-KSF as the regeneration cycles were applied. The removal of COD and TOC was the lowest when the samples were exposed to sunlight.
Mt-KSF was an excellent adsorbent to remove color; however, its efficiency decreases in each cycle. Mt-Fe-7 maintains its removal efficiencies through the cycles, showing that the modification improves the properties of the material to be regenerated, but an opposite behavior was observed for natural and modified carbon (AC-N is more efficient than AC-Cu-2).
Figure 8 shows the removal efficiencies of color when deionized water was used in the regeneration processes. The removal efficiencies by Mt-KSF and
Mt-Fe-7 decrease as the regeneration cycles were applied. AC-N showed the same removal efficiencies in each cycle. Hydrogen peroxide was added after the materials were in contact with wastewater and it plays an important role in the regeneration of materials, especially with Mt-Fe-7 where the Fenton-like process occurred.
3.6 Fixed Bed Columns
Continuous systems were evaluated with Mt-KSF, Mt- Fe-7, and AC-N. Figure 9 shows the breakthrough curves of color and TOC adsorption by each adsorbent. The parameters evaluated are not regulated by Mexican laws. For this reason, the breakthrough concentrations considered were 100 U PtCo and 15 mg/L for color and TOC, respectively. Some authors consider 10 % of the initial concentration. The breakthrough times for color with 1, 2, and 3 g of Mt-KSF were 70, 80, and 90 min; 13, 43, and 160 min for Mt-Fe-7 respectively; and 10, 15, and 35 min (3, 5, and 7 g) for AC-N. In the case of TOC, the times were 120,150, and 170 min for Mt-KSF, 20, 40, and 130 min for AC-N and 40 and 180 (2 and 3 g) for Mt-Fe-7. The breakthrough times increased as the mass of adsorbent increased because the mass transference zone is higher and there are more adsorption sites to remove color and TOC. According to the results, Mt-Fe-7 has the highest breakthrough time for color when 3 g of adsorbent was used.
3.6.1 Thomas Model
Thomas model evaluates the breakthrough curves, assuming that mass transfer limits the adsorption process,
Table 3 Langmuir and Freundlich isotherms constants of color with Mt-KSF, Mt-Fe-7, and AC-N
Color
Model Constants Adsorbents
Mt-KSF Mt-Fe-7 AC-N AC-Cu-2
Langmuir <7o (U Pt-Co/g) 29,333.51 28,341.42 162.19 63.77
2.8E-05 6.7E-06 2.1E-03 2E-03
R2 0.97 0.95 0.57 0.94
Freundlich Kf ((U Pt-Co/g)(L/U Pt-Co/)l/n) 0.52 0.08 0.41 0.32
1/n 1.13 1.18 0.92 0.78
R2 0.98 0.97 0.56 0.96
Perla Tatiana Almazán Sánchez 66
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016)227:100 Page 9 of 14 100
Fig. 7 Removal percentage of (a, c) COD, (b, d) color, and (c, f) TOC at different regeneration cycles of adsorbents with hydrogen peroxide in absence of sunlight (a, b, c) and in presence of sunlight (d, e, f) (0 corresponds to the adsorption of the solute before the first cycle)
and the data follow the Langmuir isotherm and pseudosecond-order kinetic model (Foo et al. 2013; Nguyen et al. 2015). Equation 10 shows the model:
Co J e(iCThJ°*'-*n.Cot)
where Co is the solute concentration in the influent (mg/L or U PtCo), C, is solute concentration in effluent (mg/L or U PtCo), t is time (min), KTh is the Thomas rate constant (L/mg min), q0 is the adsorption capacity (mg/g), m is the mass of adsorbent (g), and Q is the flow rate (L/min).
Figure 9 shows the breakthrough curves fitted to Thomas model, and Table 4 shows the parameters
■ 0 «■ 1 »2 «3 ss4
Fig. 8 Removal percentage of color at different adsorption-regeneration cycles of adsorbent with deionized water (0 corresponds to the adsorption of the solute before the first cycle)
Springer
obtained. Mt-KSF and Mt-Fe-7 had correlation coefficients higher than 0.80. However, Á2 was lower than 0.80 for color removal and TOC using AC-N, and this behavior could be attributed to the shape of the curves because the saturation times were not reached. When color was evaluated, the adsorption capacities increased as the heights of bed columns increased and Thomas rate constant (KTh) decreased.
It is important to note that the adsorption kinetics data showed that Mt-KSF was the best material for the removal of color because it had the higher adsorption capacity about 23-26 LI PtCo/g, followed by Mt-Fe-7. An opposite behavior was observed for TOC.
3.6.2 Yoon-Nelson Model
The application of this model may minimize the error resulting from Thomas model (Long et al. 2014; Sharma and Singh 2013; Yoon and Nelson 1984). Equation 11 shows the Yoon-Nelson model:
— = ----------------- (11)Co 1 + e^YNÍ-T/fYN)
where C„ is the solute concentration in the influent (mg/ L or U PtCo), C, is solute concentration in effluent (mg/
Perla Tatiana Almazán Sánchez 67
Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 68
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 69
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 12 of 14 Water Air Soil Pollut (2016)227:100
(Eq. 12), the additional parameters required are mass of adsorbent (g) and flow rate (L/min):
The constants obtained from Yoon-Nelson model are shown in Table 4. A?Yn decreases as the height increases when color was evaluated. The parameters obtained for TOC showed that the rate constants increase when the mass of adsorbent (Mt-KSF or Mt-Fe-7) increases, t increases as the heights of columns increases, showing that the mass transfer zone increases as well (Table 4). Comparing the data obtained with the parameters from the model, a slight difference was found when 1 and 2 g of Mt-KSF was used (110 and 140 min, respectively), and using 3 g, there was a higher difference (160 min). For the case of Mt-Fe-7, the experimental breakthrough times for color were 15, 65, 180 min for 1, 2, and 3 g when C,/Co = 0.5 respectively. They were similar to the values obtained from Yoon-Nelson model. For AC-N, t values were different from experimental data, which could be attributed to the column behaviors that did not reach the saturation, and the correlation coefficients were low (0.60-0.74). In the case of TOC, the experimental data and parameters calculated were different. A complex composition of the textile wastewater and the presence of organic and inorganic matter in the adsorption system could be responsible for this behavior.
The adsorption capacities and the correlation coefficients calculated using Thomas and Yoon-Nelson models were similar, indicating good agreement between the models.
3.6.3 Bohart-Adams Model
The Bohart-Adams model describes the initial part of the breakthrough curve (C,/Co =0-0.5). This model assumes that the adsorption rate is controlled by external mass transfer (Long et al. 2014; Nguyen et al. 2015; Sharma and Singh 2013) and it is expressed by Eq. 13:
C‘ _ e(XBACo(-XBAV04,) ( j3)Co
where Á/BA is a kinetic constant (L/mg min), F is the linear flow rate (cm/min), Z is the bed depth of column (cm), and No is adsorption capacity (mg/L of adsorbent).
Table 4 shows the parameters calculated. For adsorption of color by Mt-KSF, A"ba and No decrease as the
<£) Springer
heights of bed increase. For Mt-Fe-7 and AC-N, the rate constant decreases and adsorption capacities increase as heights increase. A typical behavior was observed because as the heights of bed increased, the saturation times and the adsorption capacities increased; this behavior was not observed for Mt-KSF. Bohart-Adams model could not be applied to the breakthrough curves for adsorption of TOC by Mt-Fe-7 and AC-N (1.1 and3.3 cm). The rate constants for the adsorption of TOC by Mt-KSF increased as the heights of bed increased and Ao decreased, it could be attributed to weak affinity between adsorbent and organic matter as it was shown in adsorption kinetics and isotherms.
4 Conclusions
Textile wastewater treatment was achieved by adsorption in batch and column systems using natural and modified clay and activated carbon. The modification of materials was performed by electrochemical process with iron and copper. This process showed that it is a good option to fix metals in solids because 10-12 % of Fe or Cu were found in the modified materials.
The characterization of textile wastewater showed a low biodegradability of organic matter present in the sample and high concentrations of inorganic ions: sulfates, phosphate, and sodium that could influence the adsorption process.
Natural and modified adsorbents were evaluated in the batch system for the adsorption of color, COD, and TOC; the first one was best removed, showing a great affinity between surface of the adsorbents and dye present in the wastewater. Mt-KSF was more efficient to remove color (90.3 %) than COD and TOC (32.4 and18.6 % respectively); Mt-Fe-7 and AC-N had a similar behavior in the removal of color COT and TOC. Data obtained were best adjusted to Elovich model (/?2>0.75) and Freundlich isotherm model, indicating a chemisorption process on heterogeneous materials.
The regeneration of adsorbents with hydrogen peroxide was achieved, and the removal efficiencies for color, TOC, and COD were kept in 4 cycles.
Fixed bed column systems show that Mt-Fe-7 had the highest breakthrough time for color and TOC (160 and 180 min, respectively). Data of breakthrough curves were best adjusted to Thomas and Yoon and Nelson.
Perla Tatiana Almazán Sánchez 70
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016)227:100 Page 13 of 14 100
Acknowledgments We acknowledge financial support from CONACYT, project 219743, and scholarship grant for PTAS No. 257364.
References
Aharoni, C., Tompkins, F. C. (1970). Kinetics of adsorption and desorption and the Elovich equation. In H. P. a. P. B. W. D. D. Eley (Ed.), Advances in Catalysis, (pp. 1-49). Academic Press.
Albuquerque, L. F., Salgueiro, A. A., Melode S, J. L., & Chiavone- Filho, O. (2013). Coagulation of indigo blue present in dyeing wastewater using a residual bittern. Separation and Purification Technology, 104, 246-249.
Amin, N. K. (2009). Removal ofdirectblue-106 dye from aqueous solution using new activated carbons developed from pomegranate peel: adsorption equilibrium and kinetics. Journal of Hazardous Materials, 165, 52-62.
Azmi, N. H. M., Ayodele, O. B„ Vadivelu, V. M„ Asif, M., & Hameed, B. H. (2014). Fe-modified local clay as effective and reusable heterogeneous photo-Fenton catalyst for the decolorization of Acid Green 25. Journal of the Taiwan Institute of Chemical Engineers, 45, 1459—1467.
Belaid, K. D„ Kacha, S., Kameche, M., & Derriche, Z. (2013). Adsorption kinetics of some textile dyes onto granular activated carbon. Journal of Environmental Chemical Engineering, I, 496-503.
Butrón, E., Juárez, M. E., Solis, M., Teutli, M., González, 1., & Nava, J. L. (2007). Electrochemical incineration of indigo textile dye in filter-press-type FM01-LC electrochemical cell using BDD electrodes. Electrochimica Acta, 52, 6888-6894.
Cañizares, P, Martinez, F., Jiménez, C., Lobato, J., & Rodrigo, M. A. (2006). Coagulation and electrocoagulation of wastes polluted with dyes. Environmental Science & Technology, 40, 6418-6424.
Cardoso, J. C., Lucchiari, N., & Zanoni, M. V. B. (2015). Bubble annular photoeletrocatalytic reactor with TiO2 nanotubes arrays applied in the textile wastewater. Journal of Environmental Chemical Engineering, 3, 1177—1184.
DíazGómcz-Treviño, A. P, Martinez-Miranda, V., & Solache- Ríos, M. (2013). Removal of remazol yellow from aqueous solutions by unmodified and stabilized iron modified clay. Applied Clay Science, 80-81, 219-225.
Doumic, L. I., Soares, P. A., Ayude, M. A., Cassanello, M., Boaventura, R. A. R., & Vilar, V. J. P. (2015). Enhancement of a solar photo-Fenton reaction by using ferrioxalate complexes for the treatment of a synthetic cotton-textile dyeing wastewater. Chemical Engineering Journal, 277, 86-96.
Firmino, P. I. M., da Silva, M. E. R., Cervantes, F. J., & dos Santos, A. B. (2010). Colour remo val of dyes from synthetic and real textile wastewaters in one- and two-stage anaerobic systems. Bioresource Technology, 101, TTT3-TTT9.
Foo, K. Y, Lee, L. K., & Hameed, B. H. (2013). Preparation of tamarind fruit seed activated carbon by microwave heating for the adsorptive treatment of landfill leachate: a laboratory column evaluation. Bioresource Technology, 133, 599-605.
Franca, R. D. G., Vieira, A., Mata, A. M. T, Carvalho, G. S., Pinheiro, H. M., & Lourenco, N. D. (2015). Effect of an azo dye on the performance of an aerobic granular sludge sequencing batch reactor treating a simulated textile wastewater. Water Research, 85, 327—336.
Freundlich, H. M. F. (1906). Over the adsorption in solution. Journal of Physical Chemistry, 57, 385—470.
Gutiérrez-Segura, E., Solache-Ríos, M., & Colin-Cruz, A. (2009). Sorption of indigo carmine by a Fe-zeolitic tuff and carbonaceous material from pyrolyzed sewage sludge. Journal of Hazardous Materials, 170, 1227—1235.
Hayat, H., Mahmood, Q., Pervez, A., Bhatti, Z. A., & Baig, S. A. (2015). Comparative decolorization of dyes in textile wastewater using biological and chemical treatment. Separation and Purification Technology, 154, 149—153.
Ho, Y.-S. (2006). Review of second-order models for adsorption systems. Journal of Hazardous Materials, 136, 681-689.
Kadirvelu, K., Kavipriya, M., Karthika, C., Radhika, M., Vennilamani, N., & Pattabhi, S. (2003). Utilization ofvarious agricultural wastes for activated carbon preparation and application for the removal of dyes and metal ions from aqueous solutions. Bioresource Technology, 87, 129-132.
Khelifi, E., Gannoun, H., Touhami, Y, Bouallagui, H., & Hamdi, M. (2008). Aerobic decolourization of the indigo dye- containing textile wastewater using continuous combined bioreactors. Journal of Hazardous Materials, 152, 683-689.
Lagergren, S. (1898). About the theory of so-called adsorption of soluble substances, Kungliga Svenska Vetenskapsakademiens. Handlingar, 24(4), 1-39.
Langmuir, I. (1918). The adsorption of gases on plane surfaces of glass, mica and platinum. Journal of the American Chemical Society, 40, 1361-1403.
Lee, K.-C., Beak, H.-J., & Choo, K.-H. (2015). Membrane photoreactor treatment of 1,4-dioxane-containing textile wastewater effluent: Performance, modeling, and fouling control. Water Research. doi:10.1016/j.watres.2015.05.017.
Long, Y, Lei, D„ Ni, J., Ren, Z, Chen, C„ & Xu, H. (2014). Packed bed column studies on lead(II) removal from industrial wastewater by modified Agaricus bisporus. Bioresource Technology, 152,457-463.
Mesquita, I., Matos, L. C., Duarte, F., Maldonado-Hódar, F. J., Mendes, A., & Madeira, L. M. (2012). Treatment of azo dye- containing wastewater by a Fenton-like process in a continuous packed-bed reactor filled with activated carbon. Journal of Hazardous Materials, 237-238, 30-37.
Metcalf, & Eddy. (2003). Wastewater engineering: treatment and reuse (4th ed., pp. 153—154). New York: McGraw Hill.
Nguyen, T. A. H., Ngo, H. H., Guo, W. S., Pham, T. Q., Li, F. M., Nguyen, T. V, & Bui, X. T. (2015). Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): fixed-bed column study. Science of the Total Environment, 523, 40-49.
Oluwakemi Kehinde, F., & Abdul Aziz, H. (2015). Classical optimization of process variables in the treatment of real textile wastewater using clinoptilolite. Journal of Environmental Chemical Engineering, doi: 10.1016/j.jece. 2015.08.019.
Polat, D., Balci, 1., & Ózbelge, T. A. (2015). Catalytic ozonation of
an industrial textile wastewater in a heterogeneous
(Y Springer
Perla Tatiana Almazán Sánchez 71
Tratamientos avanzados para la remoción de un colorante de origen textil”
100 Page 14 of 14 Water Air Soil Pollut (2016)227:100
continuous reactor. Journal of Environmental Chemical Engineering, 3, 1860-1871.
Sanromán, M. A., Pazos, M„ Ricart, M. T., & Cameselle, C. (2005). Decolourisatlon of textile indigo dye by DC electric current. Engineering Geology, 77, 253-261.
Sharma, R., & Singh, B. (2013). Removal of Ni (II) ions from aqueous solutions using modified rice straw in a fixed bed column. Bioresource Technology, 146, 519-524.
Soares, P. A., Batalha, M., Souza, S. M. A. G. U., Boaventura, R. A. R., & Vilar, V. J. P. (2015). Enhancement ofa solar photo- Fenton reaction with ferric-organic ligands for the treatment
of acrylic-textile dyeing wastewater. Journal of Environmental Management, 152, 120-131.
Tones Pérez, J., Solache-Rios, M„ & Colin Cruz, A. (2008). Sorption and desorption of dye remazol yellow onto a Mexican surfactant-modified clinoptilolite-rich tuff and a carbonaceous material from pyrolysis of sewage sludge. Water, Air, A Soil Pollution, 187, 303-313.
Yoon, Y. H., & Nelson, J. H. (1984). Application of gas adsorption kinetics I. A theoretical model for respirator cartridge service life. American Industrial Hygiene Association Journal, 45, 509-516.
£) Springer
Perla Tatiana Almazán Sánchez 72
“Tratamientos avanzados para la remoción de un colorante de origen textil”
5.3 Tercer artículo de investigación
En esta sección se muestra el tercer artículo de investigación realizado aplicando
proceso de Fenton y foto-Fenton heterogéneo solar a soluciones acuosas del colorante y al
agua residual textil, usando los materiales modificados como catalizadores y la radiación
UV concentrada en un CPC-2D
5.3.1 Carta de envío
FuelRef: JFUE-D-16-01524Title: Treatment of textile industrial wastewater by solar photo-Fenton powered by CPC-2DAuthors: Paul William Marin-Noriega; Eduardo González-Mora; Ivonne Linares- Hernández; Marcos. J. Solache-Ríos; Iván G. Martínez-Cienfuegos; Verónica Martínez Miranda; Perla Tatiana Almazán-Sánchez, M.D.Article Type: SI: IMCCRE 2016
Dear Prof. Perla Tatiana Almazán-Sánchez,
Your submission entitled "Treatment of textile industrial wastewater by solar photo- Fenton powered by CPC-2D" has been assigned the following manuscript number: JFUE-D-16-01524.
Thank you for submitting your work to this journal. Please do not hesitate to contact me if you have any queries.
Kind regards,
Administrative Support AgentAdministrative Support Agent [21-May-14]Fuel
Perla Tatiana Almazán Sánchez 73
“Tratamientos avanzados para la remoción de un colorante de origen textil”
5.3.2 Manuscrito
Treatment of textile industrial wastewater by solar photo-Fenton powered by CPC-
2D
Paul William Marin-Noriegaa, Eduardo González-Moraa, Ivonne Linares-Hernándezb,
Marcos. J. Solache-Ríosc, Iván G. Martínez-Cienfuegosa, Verónica Martínez Mirandab, Perla Tatiana Almazán-Sánchezb,c*
a Facultad de Ingeniería, Universidad Autónoma del Estado de México, Cerro de
Coatepec S/N, Ciudad Universitaria, C.P. 50100 Toluca, Estado de México, México
b Centro Interamericano de Recursos del Agua (CIRA), Universidad Autónoma del
Estado de México, Facultad de Ingeniería, Unidad San Cayetano, Km.14.5 carretera
Toluca-Atlacomulco, C.P. 50200 Toluca, México.
c Instituto Nacional de Investigaciones Nucleares (ININ), Departamento de Química,
carretera México-Toluca S/N, La Marquesa, C.P. 52750, Ocoyoacac, Estado de México,
México
(*) corresponding author: ptalmazans_88@yahoo.com
Abstract
Heterogeneous photo-Fenton process was applied to treat aqueous solutions of
indigo blue and textile wastewater using a compound parabolic concentrator (CPC-2D) to
concentrate UV radiation from sunlight and as catalyst an iron modified clay (Mt -Fe-7)
and copper modified activated carbon (AC-Cu-2) modified by electrochemical process.
The treatment was done at pH of 7.0 and 6.8 for aqueous solutions and textile wastewater
respectively, hydrogen peroxide dosage (0.1, 0.3 and 0.5 M) and catalyst (0.5, 1.0 and 1.5
g) were evaluated. The concentration of UV-A and UV-B radiation by CPC-2D was
Perla Tatiana Almazán Sánchez 74
“Tratamientos avanzados para la remoción de un colorante de origen textil”
54.29±0.71 and 1.65±0.37 W/m2 respectively, with an applied energy of 98.067 KJ. The
removal efficiencies of indigo blue by Mt-Fe-7 and AC-Cu-2 were of 98% and 99% at 1.5
h and 3.0 h respectively applying the highest amount of catalyst used (1.5 g), H2O2 dosage
(0.5 M) and UV radiation concentrated with CPC-2D. 93% of removal of color was
achieved after 4 h of treatment for textile wastewater using 1.5 g of AC-Cu-2, 0.5 M of
H2O2 and UV radiation. The removal of dye and color was improved using AC-Cu-2 and
UV radiation for both systems (aqueous solutions and textile wastewater).
Keywords: Textile wastewater; indigo blue; heterogeneous photo-Fenton; compound
parabolic concentrator (CPC).
1. Introduction
Nowadays the textile industry promotes the pollution of natural water bodies due
to the large amounts of wastewaters produced. They have a complex composition of
organic and inorganic matter, the first one includes high concentration of dye [1] and other
compounds (as surfactants) that are non-biodegradable pollutants [2] and the second one
could contain some salts and metals, all of them used in the dying of cloths [3]. The
variable physicochemical composition of textile wastewater does not allow to apply a
specific process, however some treatments have been used to remove dyes from this kind
of samples, for instance biological process [4-7], adsorption [8-10], coagulation and
electrocoagulation [11, 12]. Advanced Oxidation Processes (AOPs) have been applied to
oxidize organic matter in textile wastewater [13], the most important reagent is hydroxyl
radical (•OH), the second most powerful oxidant [14] and it can achieve the partial or total
mineralization of the organic compounds [15], some examples of these treatments are
photocatalysis [16], homogeneous and heterogeneous photo-Fenton processes [17-20],
ozonation [2, 21], electro-oxidation [22], etc. Specifically, heterogeneous Fenton process
consists on ions of iron or copper fixed in solid materials (catalysts), they promote the
formation of hydroxyl radical from hydrogen peroxide. This process is more preferred than
homogeneous process, because there is not any formation of sludge and the adjust the pH
Perla Tatiana Almazán Sánchez 75
“Tratamientos avanzados para la remoción de un colorante de origen textil”
of wastewater after of treatment is not necessary [23]. Photo-Fenton process uses as
reagent the UV radiation, and the principal source of UV ray used are UV lamps but they
have a short half time and require energy to operate, however the solar energy is a free
source of UV rays and it can be implemented in photo-Fenton processes to make more
sustainable the treatments. In this regard, compound parabolic concentrators (CPC) have
been development to use in photolysis and photocatalysis processes because they can
concentrate infrared radiation and also UV and visible radiation, these devices can be of
two or three dimensions.
The geometry of compound parabolic concentrators (CPC) have been used in
photolysis and photocatalysis processes. CPC-2D consists of two parabolic reflectors, each
side is a segment of a rotated parabola thus, all the rays incident parallel to the focal axis
of the parabola within the acceptance angle to the axis of symmetry of the CPC and they
will be concentrated [24, 25]. In 1974, Wiston described the CPC-2D showing its
advantages and also demonstrate that CPC can achieve the theoretical maximum
concentration ratio according to the 2nd law of thermodynamics [26]. Fig. 1a shows the
geometric parameters of a CPC-2D, where a is the length of aperture, a' is the length of
concentration, L is the height of CPC and I is the width of CPC, A is the entrance area and
A' is the concentration area.
The equations that describe the CPC-2D are in polar coordinates (r, t) with origin
in the focus F and with a focal distance /, the parabola is given by Eq. 1, whereas the
height of CPC is calculated by Eq. 2. The parabola equation for a CPC is shown by Eq.
3:
r = 2f1-sin t
Q^(l+sin Omax) cos ^max
(sin 0max)2
ri(t) = 2a'((1+sini9)cos(t+9)-1) , -e <t<--2e 2
Perla Tatiana Almazán Sánchez
(1)
(2)
(3)
76
“Tratamientos avanzados para la remoción de un colorante de origen textil”
The objective of this work was built a CPC-2D to concentrate the UV rays, in order
to apply them in the heterogeneous photo-Fenton process to treat aqueous solutions of
indigo blue and textile wastewater using as catalyst iron modified clay and copper modified
activated carbon.
2. Material and methods
2.1 Design and construction of CPC-2D
CPC-2D was designed to concentrate UV rays and used them to treat 1 L of textile
wastewater, applying an energy of 10 kJ/L, a treatment time of 3600 s, and considering
that only 30 % of radiation can be concentrated and 10% correspond to UV radiation,
the total heating power delivered to the water (P) is 95.59 W. The average global
irradiation (Gg) in Toluca's City is approximately 600 W/m2; with this data the aperture
area (4) of CPC is calculate by P/Gg =154.32 m2. According with Fig. 1a, the aperture
area can be calculate by A = 2al and setting the length (1) value as 0.45 m, the value of
a is 0.17 m, so 2a=0.34 m. The value of a' is 0.11 m; it was obtained considering V =
2a'lh = 0.001 m3 and h=0.001m (2a'=0.22 m). In order to calculate the half acceptance
angle is necessary calculate the geometrical concentration factor (C =
2al/2a'l = A/A'), with the proposed geometry C =1.54. The half acceptance angle is
given by Eq. 4, then the height of CPC was 0.33 m, finally replacing in Eq. 3 the data
calculated before, the parabola's equation of CPC-2D is obtained (Eq. 5).
6 = sin-1 Q) = 40.39° = 0.70 rad (4)
r(t) = °.36cos(t+°.70) _ 0.30 t = [0.70; 0.16] (5)1-sin t
The parameters calculated before were used to build the CPC-2D (Fig. 1b), the
structure was made of steel to give a parabolic profile to the CPC. MIRO-SUN® aluminum
sheets were used to reflect the UV rays, these sheets are provided with a PVD (physical
Perla Tatiana Almazán Sánchez 77
“Tratamientos avanzados para la remoción de un colorante de origen textil”
vapor deposition) layer system, guaranteeing a 95 % total reflection. For the concentration
area, a glass vessel was provided with an input and output flow to recirculate the
wastewater. The UV-A and UV-B radiation were measured by using Ahlborn Almemo
2590 sensors during the experimentation (10:00 am to 15:00 pm).
2.2 Catalyst
The catalyst used in heterogeneous photo-Fenton process was prepared according
to previous work [27]; montmorillonite clay and activated carbon were modified
employing electrochemical methods, it was carried out using an electrochemical cell with
10 g of clay or activated carbon and 0.08 L of deionized water. The conditions for clay
were an array of Fe/Fe electrodes at pH 7 for 130 min (Mt-Fe-7) and for activated carbon
an array of Cu/Cu at pH 2 for 76 min (AC-Cu-2). Finally the modified materials were
washed several times and dried at 90 °C for 18 h. Materials were characterized by scanning
electron microscopy (SEM) and elemental X-ray dispersive spectroscopy (EDS) using a
Jeol JSM-6610LV microscope. The content of iron and copper in the modified materials
was measured by atomic absorption spectroscopy, using a Varian SpectrAA-600
spectrophotometer. The catalysts were put in a Teflon vessel with 45 mL of deionized
water and 5 mL of a mixture of HCl:HNO3 (1:2) and they were treated using a microwave
digester CEM in order to extract the iron or copper.
2.3 Aqueous solutions of indigo dye
Aqueous solutions were prepared with a concentration of 28-30 mg/L using an
indigo blue dye obtained from textile industry in México, this dye is used in the dying of
denim clothes. The concentration of dye was determined by UV-Vis spectrophotometer
Cary Varian at 591 nm.
2.2 Textile wastewater sampling and characterization
Perla Tatiana Almazán Sánchez 78
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Textile wastewater sample was taken from effluent of Mexican textile industry
where denim jeans are manufactured. The sample was collected and subsequently
characterized considering the follow parameters: pH, alkalinity, acidity, hardness,
chemical oxygen demand (COD), biochemical oxygen demand (BOD5), color, total
organic carbon (TOC), inorganic ions (sulfates, phosphate, nitrites, nitrates, chloride) and
metals (Na, K, Mg, Ca, Si, Mn, Fe). Each of these parameters were determined by Standard
Methods and Procedures [28]. The sample was also analyzed by UV-Vis spectrophometer
analyzer Carey Varian and Fourier Transform infrared (IR) spectrophotometer HART
mode (IR Prestige-2).
2.1 Fenton and photo-Fenton processes
Oxidation processes by Fenton and photo-Fenton were carried out using 1 L of
aqueous solutions of indigo blue (28-30 mg/L) and textile wastewater treatment, different
dosages of catalyst and hydrogen peroxide were used, 0.5, 1.0 and 1.5 g of Mt-Fe-7 or AC-
Cu-2 and 0.1, 0.3 and 0.5 M of H2O2 (30%, J. T. Baker) were applied in the treatment of
aqueous solutions and textile wastewater. Aqueous solutions of indigo blue and textile
wastewater were recirculate in CPC-2D using a peristaltic pump, with a flow rate of 0.2
L/min, and at different times, an aliquot was taken to monitoring the concentration of dye
and color during treatment. Each of these treatment were performance in presence and
absence of sunlight to ensure the effect of UV radiation in the oxidation of dye. The
experiments were carried out at pH of 6.86 for textile wastewater and 7.0 for aqueous
solutions. Infrared analyses were done to samples that showed the best removal
efficiencies. Furthermore the catalysts were reused in a second time in contact with
aqueous solutions and wastewater under the best conditions (catalyst dosage and H2O2
concentration) to evaluate their efficiencies.
3. Results
Perla Tatiana Almazán Sánchez 79
“Tratamientos avanzados para la remoción de un colorante de origen textil”
3.1 Analysis of concentrated UV radiation
The CPC-2D was designed to concentrate UV-A radiation from sunlight and
applied to a heterogeneous photo-Fenton process to treat textile wastewater. Fig. 2a shows
the irradiation outside an inside of the concentration line of the CPC-2D, where the dotted
line corresponds to a polynomial function and Fig. 2b shows the maximum and minimum
irradiation measured out of the CPC-2D. The UV-A and UV-B irradiations out of
concentration line were very unstable of 40.35±9.57 and 0.94±0.22 W/m2, respectively,
due the climatological conditions, however the concentrated UV-A irradiation was almost
constant with an average of 54.29±0.71W/m2. Eq. 6 and 7 show the integration of
polynomial equation of minimum (Fx(%)) and maximum (F2(%)) UV-A irradiations from
Fig. 2b; Eq. 8 and 10 show the corresponding integration of non-concentrated
(F3(x);F5(x)) and concentrated (F4(%); F6(x) ) UV-A and UV-B irradiations respectively
outside and inside the concentration line in the CPC with times of 3.0 h and 4.5 h.
Considering the result of the integrated equations 8 and 9 with the aperture area (A) and
concentration area (A') of CPC respectively, a geometrical concentration factor (C =
A/A') could be calculated again (1.502), it is very similar to the one calculated before in
Fig. 1 a) Geometric parameters of CPC-2D and b) CPC-2D constructed to use in textile
wastewater treatment
Perla Tatiana Almazán Sánchez 80
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fig. 2 Solar irradiation during photo-Fenton process: a) ▲Maximum and □ minimum
irradiation out of CPC-2D; • Concentrated irradiation inside of concentration line and ◊
Irradiation out of concentration line in CPC for b) UV-A and c) UV-B of February 19th,
2016 and March 18th, 2016 in Toluca, Estado de México (Latitude: 19° 24' N; Longitude:
99°42' W)
UV - Amín = J°4'F1(x) = 0.186%6 - 2.506%s + 13.579%4 - 39.104%3 + 62.711%2 - 49.017% + 36.562 =
101.595rn
- F2(x) = 0.8196%6 - 9.9993%5 + 45.355%4 - 93.574%3 + 82.597%2 - 16.984% + 44.593 =
219.608
F3(%) = -8 X 10-6%6 + 3 X 10-4%5 - 4.4 X 10-3%4 + 0.016%3 + 0.092%2 - 0.707% + 58.820 =
174.243
3UV - = JO
Í4(%) = -3 X 10-4%6 - 0.018%5 - 0.397%4 + 4.196%3 - 20.474%2 + 38.158% + 20.276 =
116.002
W-B = JO,f5(%) = -4 X 10-6%6 + 3 X 10-4%5 - 6.2 X 10-3%4 + 0.068%3 - 0.329%2 - 0.544% + 0.809 =
3.021
UV - = J°3F6(%) = -2 X 10-6%6 + 8 X 10-5%5 - 1.3 X 10-3%4 + 0.008%3 - 0.014%2 - 0.016% + 1.594 =
4.692
(6)
(7)
(8)
(9)
(10)
(11)til
W = JO4
^-¿ = J¡3
m
O
It is possible to calculate the energy applied to textile wastewater treatment in CPC
using Eqs. 6-9 and the inherent parameters, such as geometrical concentration factor
(C =1.502), total area (0.091 m2), maximum UV-A irradiation (W - =
219.608 l-¥h/m2) and concentration line area in CPC (0.022 m2). The maximum
Perla Tatiana Almazán Sánchez 81
“Tratamientos avanzados para la remoción de un colorante de origen textil”
concentrated UV-A irradiation is calculated by Eq. 10 (214.009x 1.54 =
329.574 Wh/m2) and the maximum energy applied to wastewater by Eq. 11.
UV-Amax(conc) UV-AmaxxC = 329.851 Whm2
(12)
Energy = [(^7 - Amax x Total area) + (y^max(conc) x Concentration line area)] = 27.241 Wh « 98.067 KJ (13)
3.2 Characterization of catalyst
Catalysts were characterized by EDS to know the content of iron and copper
present after modification of clay an activated carbon. The analysis was done before and
after of electrochemical modification, an increment of iron in modified clay of 9.67% with
respect to natural clay was observed and for activated carbon the content of copper was
12.02%. Comparing EDS data with atomic absorption analysis, the content of iron in
natural and modified clay was 23.26 mg/g and 57.66 mg/g and-for activated carbon the
content of copper was 22.96 mg/g. Yao et-al. 2013 [17] impregnated carbon fibers with
FeCl3 to oxidize Reactive Red M-3BE and the content of iron in the material was 66.8
|imol Fe/g (3.84 mg Fe/L) it was lower than iron modified clay used in this work, these
results show that the electrochemical process modification is a good option to fix metallic
ions on the materials used as catalyst in heterogeneous Fenton process.
3.3 Wastewater characterization
3.3.1 Physicochemical characterization of textile
Table 1 shows the parameters evaluated in textile wastewater sample. According
with these results, the biodegradable index (BOD5/COD) is 0.23, and according to Metcalf
& Eddy (2003) [29] if the value is lower than 0.3 the organic matter is non-biodegradable
and could be toxic to microorganism used in biological treatments. Total phosphorous
concentration (93.67 mg/L) is higher than the maximum permissible limit established by
Mexican's Law (5-30 mg/L) for wastewater discharged in superficial water bodies, the
Perla Tatiana Almazán Sánchez 82
“Tratamientos avanzados para la remoción de un colorante de origen textil”
concentration of chlorides and sulfates is high and they presence in water could cause
eutrophication [30] and salinization [31] problems. The concentration of TOC was 417
mg/L and considering the biodegradation index is possible that organic matter could be
toxic due to the presence of dye and surfactant with low biodegradability. [13, 32].
Table 1 Physicochemical parameters evaluated in textile wastewater
Parameter Units ValuepH 6.86
Alcalinity mg/L CaCO3 267.13Acidity mg/L CaCO3 155.63
Hardness mg/L CaCO3 139.03COD mg/L O2 539.00BOD5 mg/L O2 121.91TOC mg/L 416.92Color U PtCo 642.00SO42’ mg/L 172.90PO43’ mg/L 287.08
Cl“ mg/L 241.20N-NO3- mg/L 2.43N-NO2- mg/L 1.69MBAS mg/L 0.11
Na mg/L 67.15K mg/L 42.50
Mg mg/L 12.30Ca mg/L 7.54
The UV-Vis spectra of the aqueous solution and denim wastewater are shown in
Fig. 3 There is an adsorption peak in the region around 250-300 nm in the spectra, it could
be associated to dye's components (organics and aromatics). It is interesting that a
displacement of maximum absorption band in textile wastewater was observed in
comparison to aqueous solution of indigo blue from 591 nm to 661 nm, it could be
attributed to interference of other organic and inorganic matter used during the process of
denim present in the textile sample.
Perla Tatiana Almazán Sánchez 83
“Tratamientos avanzados para la remoción de un colorante de origen textil”
2.0 -------Textile wastewater
1.5 »tt»I
-------Aqueous solution of indigo blue
c 1.0 -
I»I1VIV * X 661 nmX
X X 591 nm /0.5 X XXX ¡ /
¡ /
0.0 1------------ 1------ t200 300 400 500 600 700 800
Wavelength (nm)
Fig. 3 UV-Vis spectra of aqueous solutions of indigo blue and textile wastewater.
3.4 Oxidation process for aqueous solution
3.4.1 Effect of UV radiation + H2O2
The UV/H2O2 process uses ultraviolet radiation to cleave the O-O bond in H2O2
and generate hydroxyl radicals (•OH). Subsequently, the •OH can be scavenged by any
organic compound present in wastewater to initiate a radical chain degradation of H2O2 in
the critical chemical and photochemical reactions taking place in the UV/H2O2 process
[33].
Fig. 4 shows different treatments applied to aqueous solution to evaluate the effect
of concentration of hydrogen peroxide (0.1, 0.3 and 0.5 M) with an UV-A and UV-B
radiation of 54.29±0.71 and 1.65±0.37 W/m2 concentrated in CPC-2D. A tendency was
observed because when H2O2 concentration increases the removal efficiency increases,
approximately at 2.5 h of treatment with 0.5 M of H2O2 the removal was of 98.52%. Eq.
14 shows that UV radiation is a catalyst that promote the formation of hydroxyl radical
(OH*) from hydrogen peroxide [14].
H2O2 + hv —— 2 *OH
Perla Tatiana Almazán Sánchez
(14)
84
“Tratamientos avanzados para la remoción de un colorante de origen textil”
00
30
25
20
15 -
10
IS♦ ♦
ISI B g □
♦
5♦
00.0 0.5 1.0
□▲
■ ♦-n------- "--------■1.5 2.0 2.5t (h)
43.0
Fig. 4 Effect of H2O2 concentration and UV radiation (• 0.1 M H2O2 + UV, ♦ 0.3 M
H2O2 + UV, ■ 0.5 M H2O2 + UV, ▲0.5 M H2O2, □ 0.5 M H2O2 + 1.5 g Mt-Fe-7)
Degradation of organic compounds can take place by absorption of UV light
(photolysis) or reaction with •OH, some compounds may even be mineralized towards
CO2 and H2O (Eq. 15) [34].
Organic compound + •OH + hv degradation compound + CO2 + H2O (15)
According to De La Cruz, et al., (2013) [35] (De la Cruz et al., 2013) (De la Cruz
et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De
la Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al.,
2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De la
Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al., 2013) (De la Cruz et al.,
2013) (De la Cruz et al., 2013) other mechanisms of direct or indirect photolysis can take
place. Direct photolysis can take place when target compounds are exposed directly to
light, which may cause electronic excitation of the organic substrate, which leads to
electron transference from the excited state of the substrate to molecular oxygen to form
organic radicals that react with oxygen. In addition, there is a variety of indirect
Perla Tatiana Almazán Sánchez 85
“Tratamientos avanzados para la remoción de un colorante de origen textil”
photochemical reactions involving photosensitizers, which can be found in dissolved
organic matter present in water. They can lead to the formation of reactive species to
initiate pollutants degradation.
When UV radiation was not applied, the oxidation of dye in aqueous solution was
not achieved (removal of 1.93%) and the same behavior was observed when heterogeneous
Fenton process (0.5 M H2O2 + Mt-Fe-7) took place because only a removal of 4.98% was
obtained after 3 h of treatment although the major hydrogen peroxide was applied. These
results indicate that a slightly higher efficiency was obtained using Fenton process, UV
radiation plays an important role in the formation of •OH radicals.
3.4.2 Effect of catalyst and H2O2 in photo-Fenton process
A series of experiments were carried out with the advanced oxidation process of
photo-Fenton (UV/H2O2/Fe) at pH 7 for the dye removal. Fig. 5 shows the results obtained
in heterogeneous photo-Fenton, where 0.5, 1.0 and 1.5 g of catalyst (Mt-Fe-7 or AC-Cu-
2), concentrations of H2O2 of 0.1, 0.3 and 0.5 M, and UV radiation from sunlight were
used. Fig. 5 a, b and c show the concentration of dye at different times of treatment using
Mt-Fe-7, Fig. 5 d, e and f correspond to AC-Cu-2 catalyst. According to data obtained
from atomic absorption analysis the concentration of iron and copper in modified materials
was 57.66 and 22.96 mg/g, respectively, and 0.5, 1.0 and 1.5 g/L of each catalyst were
used, the real concentration of iron per liter of water was 28.83, 57.66 and 86.49 mg/L and
for copper 11.48, 22.96 and 34.44 mg/L. AC-Cu-2 was more efficient than Mt-Fe-7
although similar removal efficiencies of dye were obtained (99% and 98% respectively)
with a concentration of 0.5 M of H2O2, the dye concentration was reduced in 1.5 h using
AC-Cu-2 whereas for Mt-Fe-7 was in 3.0 h approximately, the concentration of iron in the
modified clay was higher than copper in activated carbon and the last one gave the best
efficiency.
The Fenton process is based on the generation of hydroxyl radicals through the
reaction of iron (II) and H2O2 (Eq. 16) and Fenton-Like process is represented in Eq. 17
where hydroperoxyl (•HO2) radicals are formed from hydrogen peroxide, this reaction is
Perla Tatiana Almazán Sánchez 86
“Tratamientos avanzados para la remoción de un colorante de origen textil”
catalyzed by ferric and ferrous ions present in modified clay. Also, copper has been used
as catalyst agent that promote the formation of radicals (Eqs. 18-19) [36]. When the
treatment is photo-assisted with UV radiation, Fe(III)-hydroxyl complexes could be
dissociated to produce Fe (II) and an oxidized ligand (Eq. 20). This oxidation of the ligand
can also contribute to contaminant degradation [37]. In this way, the cycle of the iron
catalyst (II-III) can be maintained.
Fe2+(surf)+ H2O2 — OH* + Fe3+(surf) (16)
Fe3+(surf) + H2O2— Fe2+(surf) + H+ + •HO2 (17)
Cu2+(surf) + *HO2 — Cu+(surf) + H+ + O2(g) (18)
Cu+(surf) + H2O2 — Cu2+(surf) + *OH + OH— (19)
Fe3+(L)n + hv — Fe2+(L)n-1 + L*ox (20)
30
25
20
10
0.0
30
25
20
15
10
0.0
a)
1.0 2.0 3.0 4.0Time (h)
d)
A □ ° o A O
2 ° o
0, a a ó0.5 1.0 1.5 2.0
Time (h)
"I.
0.0
30 Ü
25i20
15 -
10
5
00.0
1.0
0.5
b)30
25
20
15
c)
2.0
Time (h)3.0 4.0
0.0
e) 30
25
20
15
10
1.0 1.5
Time (h)2.0 0.0
B.I.
1.0 2.0 3.0 4.0Time (h)
f)
□A 5-p-?-
0.5 1.0 1.5
Time (h)2.0
* A |
5
5
0
5
0
▲ •
□ó □
Ó
A
□
0
5
0
□A
□A
Fig. 5 Photo-Fenton process (Fe/Cu + H2O2+ UV) applied to aqueous solution using
different catalyst dosage (A/A0.5 g, ■/□ 1.0 g, »/o1.5 g) and H2O2 concentration a) Mt-
Perla Tatiana Almazán Sánchez 87
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fe-7 0.1 M, b) Mt-Fe-7 0.3 M and c) Mt-Fe-7 0.5 M, d) AC-Cu-2 0.1 M, e) AC-Cu-2 0.3
M and f) AC-Cu-2 0.5 M
Results show that the highest activity in the heterogeneous photo-Fenton is
achieved with a power UV radiation of 54.29±0.71 W/m2. The radiation increases the
activity of the system favoring the formation of radicals, producing a higher amount of
oxidizing species as shown Eqs. 21-23:
H2O + hv -H + -OH (21)
R + hv -R (22)
Fe3+OH(surf) + hv Fe2+(surf)+ -OH (23)
Radiation may also enhance the heterogeneous Fenton activity on the surface of the
iron or copper particles, by promoting the photo-reduction of Fe3+OH to Fe2+, which
subsequently reacts with H2O2 generating -OH radicals on the surface of the iron particles
In this work, AC-Cu-2 was the best catalyst due to the oxidation of indigo blue was
achieved in 1.5 h, it was less time in comparison to Mt-Fe-7 (3.0 h).
The oxidation of dye was observed by UV-Vis spectra (Fig. 6) because the
absorbance of maximum band decreases as treatment time increases. The initial
concentration of dye in this experiment was 28 mg/L, it correspond to an absorbance of
0.25 at 591 nm, then at 1 h a displacement of wavelength was observed at 579 nm and an
absorbance was 0.14, at t=2 h the wavelength was 537 nm (absorbance=0.06) and at t=3 h
the maximum band was at 527 nm (absorbance=0.03), this behavior could be attributed to
changes in the structure of dye.
The typical pH value of the homogeneous Fenton process is 2.8 to ensure that
ferrous ions are in aqueous solution to promote the formation of hydroxyl radical but this
step can generate additional cost to the process due to the sludge generated [38], however
Perla Tatiana Almazán Sánchez 88
“Tratamientos avanzados para la remoción de un colorante de origen textil”
in heterogeneous Fenton process the ions of iron and copper are fixed in solid materials
and the advantage is that there is no formation of sludge or are in much less amounts
comparing with homogeneous process. Heterogeneous Fenton process can be carried out
at neutral pH and after treatment there was not any significantly change (6.82) Dias et-al.
2016 [39] applied heterogeneous photo-Fenton to oxidize Reactive black 5 (RB5) a textile
dye using a red mud residue (waste of the aluminium industry rich in iron oxide), and they
obtained the best result at pH 3 with a removal of 100% with a concentration of dye and
H2O2 of 50 mg/L, respectively, whereas Al-Kahtani et-al. 2016 [40] synthetized a
nanocomposite (chitosan, cobalt ferrite and graphene oxide) and applied in photo-Fenton
process to remove Maxilon C.I. basic dye obtained the best result at pH of 9.5. These
results show that the pH and the kind of dye plays an important role in the removal of dyes,
in this work the removal of indigo blue was achieved at neutral pH, this is an advantage
because sometimes the final pH of wastewater is extreme (acid or basic) and before
discharging the pH should be adjusted.
Fig. 6 UV spectra of aqueous solution of indigo blue during photo-Fenton heterogeneous
process (1.5 g AC-Cu-2, 0.5 M H2O2) from t= 0 h to t=3 h.
3.5 Photo-Fenton process for textile wastewater
The treatment of textile wastewater was done by heterogeneous photo-Fenton
process, these studies are usually developed in acidic condition (2.5 < pH < 3-4) however
this study has been developed at near neutral pH (6.86), this provides the advantage to
Perla Tatiana Almazán Sánchez 89
“Tratamientos avanzados para la remoción de un colorante de origen textil”
avoid the acidification and neutralization of large amounts of wastewater in a real large
scale application.
Different researches have been developed in order to establish the best conditions
for the pollutants removal. According to De La Cruz, et-al. (2012) [37], the best result
could be observed for the photo-Fenton technique with UV, 5 mg/L Fe2+, and 50 mg/L of
H2O2
Fig. 7 shows that the removal efficiencies increase as hydrogen peroxide
concentration increases and 0.5 or 1.0 g of catalyst (Mt-Fe-7) was not an important factor
to promote the oxidation of color in textile wastewater because in three experiments a
similar behavior was observed, whereas for 1.5 g of Mt-Fe-7 and 0.5 M of H2O2 there is a
slightly higher removal of color in the sample. Using 0.5, 0.3 and 0.1 M of hydrogen
peroxide with 0.5, 1.0 or 1.5 g of iron modified clay an average removal efficiencies of
color were 79, 64 and 49% after 4 h of treatment. The best result for textile wastewater
were obtained using AC-Cu-2 and 0.5 M of H2O2, with removal efficiencies for 0.5, 1.0
and 1.5 g of 86%, 84% and 93% respectively, after 4 h of treatment the removal efficiencies
for Mt-Fe-7 and AC-Cu-2 were very similar under the same conditions.
u450
e300
oU
600
50
00.0 1.0 2.0 3.0 4.0
Time (h)
600
450
300
50
00.0 1.0 2.0
Time (h)3.0 4.0
Perla Tatiana Almazán Sánchez 90
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fig. 7 Photo-Fenton process in textile wastewater (Fe/Cu + H2O2+ UV) using different
catalyst dosage (A/A0.5 g, ■/□ 1.0 g, »/o1.5 g) and H2O2 concentration a) Mt-Fe-7 0.1
M, b) Mt-Fe-7 0.3 M and c) Mt-Fe-7 0.5 M, d) AC-Cu-2 0.1 M, e) AC-Cu-2 0.3 M and
f) AC-Cu-2 0.5 M
The production of *OH from H2O2 is the key step of the Fenton process. At a low
concentration of H2O2 in the system, a small amount of *OH radicals is formed, reducing
the efficiency of dye degradation. At high H2O2 concentrations, the efficiency also
decreases due to excess of *OH generated at the beginning of the process, which may lead
to undesirable parallel reactions that form H2O and O2. In addition, due to the high amount
of H2O2 the *OH radicals are consumed to produce hydroperoxyl radicals (*OOH), which
presents a lower reduction potential (E=1.42 V) compared to the *OH radical (E=2.80 V)
having a negative effect on the process [39].
Comparing data between aqueous solution of dye and textile wastewater, an
important differences in time of treatment were observed using AC-Cu-2 because in textile
wastewater there is a high concentration of organic matter that corresponds to the dye and
to surfactants, inorganic ions and other substances used in the denim processing probably
doing slower the oxidation process of dye.
It is important to consider that the photo-Fenton degradation efficiency depends on
the characteristics of the water matrix, such as turbidity, alkalinity, among others [41].
Considering Fe or Cu UV/H2O2 oxidation, chemical species known as OH* scavengers
(e.g., CO3-2, NO3-, NO2-) decrease the efficiency of the chemical degradation process. The
alkalinity of wastewater (267 mg/L) could be severely changed with the oxidation process
as well as sulfates and phosphates anions concentration.
Fig. 8 shows the results from the treatments applied to textile wastewater without
catalyst and using UV radiation, where a similar behavior using 0.3 M and 0.5 M of H2O2
was observed, with an removal efficiencies for 0.1, 0.3 and 0.5 M of 36%, 42% and 56%
respectively after 4 h of treatment. In this experiments, an important difference was
observed when a catalyst (AC-Cu-2) was applied because the removal efficiencies were
Perla Tatiana Almazán Sánchez 91
“Tratamientos avanzados para la remoción de un colorante de origen textil”
higher, showing that copper has an important effect in the formation of hydroxyl radical
that promote the oxidation of dye, and approximately in around 3.5 h the maximum
removal was observed. The pH of textile wastewater sample was 6.86, and after of
heterogeneous photo-Fenton the pH value changed to 6.75, it was not a significantly
variation and it is an important factor because it is not necessary add any other compound
to adjust the pH doing cheaper the process and the treated water can be reused minimizing
the demand of water and the impact that the textile wastewater can cause in the
environmental.
600o U0p •-_©
150
■ A A A A
I ■450
300
0 -I------------ ,------------ ,------------ ,------------ ,0.0 1.0 2.0 3.0 4.0
Time (h)
Fig. 8 Treatment of textile wastewater using ▲0.1 M, ■ 0.3 and •0.5 M of H2O2 and
UV radiation in absence of catalyst
3.6 Reuse of catalyst
Catalysts were reused a second time in order to evaluate their efficiency. AC-Cu-2
was used for aqueous solution and for wastewater both materials using 1.5 g of each used
catalyst and 0.5 M of H2O2. For aqueous solutions, the AC-Cu-2 maintains its efficiency
because the first time used the removal was of 99% and the second time was 96%. For
wastewater, the removal efficiencies for Mt-Fe-7 and AC-Cu-2 were 38% and 41%
respectively for second time, whereas the removal efficiencies the first time used were 79
and 93% showing that efficiencies decreased around 50%, it could be attributed to
inorganic matter present in textile wastewater mainly chlorides, sulfates and phosphates
because these anions have higher affinity for transition metals as iron and copper [42] and
their concentration in the sample is high and they could limit the catalytic effect in the
process. There was not any ionic interference in the aqueous solution of indigo blue with
Perla Tatiana Almazán Sánchez 92
“Tratamientos avanzados para la remoción de un colorante de origen textil”
respect to wastewater that the efficiencies were not affected when the catalyst was reused.
Probably the catalyst should be regenerated to improve their removal efficiencies. In
previous works, the catalysts (iron modified clay and copper modified activated carbon)
where applied in the treatment of aqueous solutions [27] and of textile wastewater [43] by
adsorption process, showing that for copper AC-Cu-2 there is an important effect of
inorganic matter because when the materials where applied in aqueous solution it was the
most efficient but when it was applied to textile wastewater it was the less efficient,
although in the present work the materials were used as catalysts and not as adsorbents, it
is probable that an adsorption of inorganic anions could be occurred.
3.7 Infrared analysis
Aqueous solutions of indigo blue and textile wastewater were analyzed by infrared
spectroscopy before and after of heterogeneous photo-Fenton process and the spectra are
shown in Fig. 9. The principal functional groups found in aqueous solution of dye (Fig.
9a) were N-H (3700 cm-1), -CH3, -CH2- (2920, 2850 cm-1), -NH3+ (2376, 2340, 2306 cm-
1), N-C (2160 cm-1), aromatic rings (1990, 1592, 833 cm-1), C-C=O (1056, 686 cm-1). The
spectra of treated water by 1.5 g of AC-Cu-2 and 0.5 M of H2O2 (Fig. 9b) shows that the
intensity of corresponding bands to methyls and methylenes diminished after of treatment
whereas the bands of -NH3+ and N-C increase, and a slight displacement of C-O-C band
was observed, it could be attributed to the oxidation of dye as was observed in UV-Vis
spectra (Fig. 6), and at 2580 cm-1 a band appear it correspond to amines hidrohalides.
Some of by-products formed during oxidation process of indigo blue could be 1H-indoline-
2,3-dione and 2-(2-aminophenyl)-2-oxoacetic acid [27, 44]. On the other hand, the IR
spectra of textile wastewater (Fig. 9c) the band at 3288 cm-1 and 1558 cm-1 correspond to
N-H vibration, 2922 cm-1 to -CH3 and -CH2, 1654 cm-1 to C-N, , 1066 cm-1 to C-C=O. In
contrast to treated wastewater with Mt-Fe-7 and AC-Cu-2 (Fig. 9d and 9e) under the best
conditions, the spectra show an important change in the band corresponding to N-H
because the form of the band is characteristic of -OH from carboxylic acid and the bands
of -CH3, -CH2 and C-C=O decreased showing a change in the organic matter in textile
wastewater.
Perla Tatiana Almazán Sánchez 93
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fig. 9 Infrared spectra of a) aqueous solutions of indigo blue, b) aqueous solution treated
with AC-Cu-2, H2O2 and UV, c) textile wastewater d) textile wastewater treated with Mt-
Fe-7 and e) AC-Cu-2
Conclusions
The application of CPC-2D to concentrate UV radiation in order to carry out the
photo-Fenton process is a good option; furthermore nowadays the use of alternative source
of energy as solar energy is important to develop treatments more sustainable. The
concentration UV-A and UV-B radiation by CPC-2D was 54.29±0.71 and 1.65±0.37
W/m2, with an applied energy of 98.067 KJ
Catalyst used in heterogeneous photo-Fenton was more efficient in the removal of
indigo blue from aqueous solution than textile wastewater, but the activated modified
activated carbon was the best, the removal efficiencies were above 90% of dye, showing
that copper is an important catalyst in Fenton process.
Heterogeneous photo-Fenton process was faster in aqueous solution of indigo blue
than textile wastewater using 1.5 g of AC-Cu-2 0.5 M of H2O2, organic and inorganic
Perla Tatiana Almazán Sánchez 94
“Tratamientos avanzados para la remoción de un colorante de origen textil”
matter present in wastewater may be responsible for this behavior. Furthermore, the pH of
treatment was 6.8-7.0. Copper present in activated carbon was better catalyst than iron
present in clay
According with IR spectra, important changes in bands were observed after photo-
Fenton process, showing that there is a chemical transformation in organic matter present
in aqueous solutions and textile wastewater.
Acknowledgments
Authors acknowledge financial support from CONACYT, project 219743 and
scholarship Grant for PTAS No. 257364, and Laboratorio de Investigación y Desarrollo
de Materiales Avanzados (LIDMA).
References
[1] Cardoso JC, Lucchiari N, Zanoni MVB. Bubble annular photoeletrocatalytic reactor
with TiO2 nanotubes arrays applied in the textile wastewater. J Environ Chem Eng
2015; 3:1177-84.
[2] Polat D, Balci i, Ozbelge TA. Catalytic ozonation of an industrial textile wastewater
in a heterogeneous continuous reactor. J Environ Chem Eng 2015; 3:1860-71.
[3] Oluwakemi Kehinde F, Abdul Aziz H. Classical optimization of process variables in
the treatment of real textile wastewater using clinoptilolita. J Environ Chem Eng
2015; 4:1242-7.
[4] Punzi M, Nilsson F, Anbalagan A, Svensson BM, Jonsson K, Mattiasson B, Jonstrup
M. Combined anaerobic-ozonation process for treatment of textile wastewater:
Removal of acute toxicity and mutagenicity. J Hazard Mater 2015; 292:52-60.
[5] Hayat H, Mahmood Q, Pervez A, Bhatti ZA, Baig SA. Comparative decolorization
of dyes in textile wastewater using biological and chemical treatment. Sep Purif
Technol 2015; 154:149-53.
Perla Tatiana Almazán Sánchez 95
“Tratamientos avanzados para la remoción de un colorante de origen textil”
[6] Franca RDG, Vieira A, Mata AMT, Carvalho GS, Pinheiro HM, Lourengo ND.
Effect of an azo dye on the performance of an aerobic granular sludge sequencing
batch reactor treating a simulated textile wastewater. Water Res 2015; 85:327-36.
[7] Pathak VV, Kothari R, Chopra AK, Singh DP. Experimental and kinetic studies for
phycoremediation and dye removal by Chlorella pyrenoidosa from textile
wastewater. J Environ Manage 2015; 163:270-77.
[8] Oguntimein GB. Biosorption of dye from textile wastewater effluent onto alkali
treated dried sunflower seed hull and design of a batch adsorber. J Environ Chemical
Eng 2015; 3: 2647-61.
[9] Chaari I, Feki M, Medhioub M, Bouzid J, Fakhfakh E, Jamoussi F. Adsorption of a
textile dye “Indanthrene Blue RS (C.I. Vat Blue 4)” from aqueous solutions onto
smectite-rich clayey rock. J Hazard Mater 2009; 172:1623-28.
[10] Vakili M, Rafatullah M, Salamatinia B, Abdullah AZ, Ibrahim MH, Tan KB,
Gholami Z, Amouzgar P. Application of chitosan and its derivatives as adsorbents
for dye removal from water and wastewater: A review. Carbohyd Polym 2014;
113:115-30.
[11] Albuquerque LF, Salgueiro AA, Melo JLdS, Chiavone-Filho O, Coagulation of
indigo blue present in dyeing wastewater using a residual bittern. Sep Purif Technol
2013; 104:246-9.
[12] Han G, Liang CZ, Chung TS, Weber M, Staudt C, Maletzko C, Combination of
forward osmosis (FO) process with coagulation/flocculation (CF) for potential
treatment of textile wastewater. Water Res 2016; 91:361-70.
[13] Asghar A, Abdul Raman AA, Wan Daud WMA. Advanced oxidation processes for
in-situ production of hydrogen peroxide/hydroxyl radical for textile wastewater
treatment: a review. J Clean Prod 2015; 87:826-38.
[14] Legrini O, Oliveros E, Braun AM. Photochemical processes for water treatment.
Chem Rev 1993; 93:671-98.
[15] Han Z, Dong Y, Dong S. Copper-iron bimetal modified PAN fiber complexes as
novel heterogeneous Fenton catalysts for degradation of organic dye under visible
light irradiation. J Hazard Mater 2011; 189: 241-8.
Perla Tatiana Almazán Sánchez 96
“Tratamientos avanzados para la remoción de un colorante de origen textil”
[16] Lucic M, Milosavljevic N, Radetic M, Saponjic Z, Radoicic M, Kalagasidis Krusic
M, The potential application of TiO2/hydrogel nanocomposite for removal of various
textile azo dyes. Sep Purif Technol 2014; 122: 206-16.
[17] Yao Y, Wang L, Sun L, Zhu S, Huang Z, Mao Y, Lu W, Chen W, Efficient removal
of dyes using heterogeneous Fenton catalysts based on activated carbon fibers with
enhanced activity. Chem Eng Sci 2013; 101:424-31.
[18] Vedrenne M, Vasquez-Medrano R, Prato-Garcia D, Frontana-Uribe BA, Hernandez-
Esparza M, de Andrés JM. A ferrous oxalate mediated photo-Fenton system: Toward
an increased biodegradability of indigo dyed wastewaters. J Hazard Mater 2012;
243: 292-301.
[19] Sun SP, Zeng X, Lemley AT. Nano-magnetite catalyzed heterogeneous Fenton-like
degradation of emerging contaminants carbamazepine and ibuprofen in aqueous
suspensions and montmorillonite clay slurries at neutral pH. J Mol Catal A-Chem
2013; 371:94-103.
[20] Doumic LI, Soares PA, Ayude MA, Cassanello M, Boaventura RAR, Vilar VJP.
Enhancement of a solar photo-Fenton reaction by using ferrioxalate complexes for
the treatment of a synthetic cotton-textile dyeing wastewater. Chem Eng J 2015;
277:86-96.
[21] Cardoso JC, Bessegato GG, Boldrin Zanoni MV. Efficiency comparison of
ozonation, photolysis, photocatalysis and photoelectrocatalysis methods in real
textile wastewater decolorization. Water Res 2016; 98:39-46.
[22] Butrón E, Juárez ME, Solis M, Teutli M, González I, Nava JL. Electrochemical
incineration of indigo textile dye in filter-press-type FM01-LC electrochemical cell
using BDD electrodes. Electrochim Acta 2007; 52:6888-94.
[23] Hassan H, Hameed BH. Fe-clay as effective heterogeneous Fenton catalyst for the
decolorization of Reactive Blue 4. Chem Eng J 2011; 171: 912-8.
[24] Duffie JA, Beckman WA. Solar Engineering of Thermal Processes. 4th ed. New
Jersey: Wiley; 2013.
[25] Rabl A. Comparison of solar concentrators. Sol Energy 1976; 18: 93-111.
Perla Tatiana Almazán Sánchez 97
“Tratamientos avanzados para la remoción de un colorante de origen textil”
[26] Winston R. Principles of solar concentrators of a novel design. Sol Energy 1974;
16:89-95.
[27] Almazán-Sánchez PT, Solache-Ríos MJ, Linares-Hernández I, Martínez-Miranda V,
Adsorption-regeneration by heterogeneous Fenton process using modified carbon
and clay materials for removal of indigo blue. Environ Technol 2016, 37:1843-56.
[28] APHA, AWWA. Standard methods for the examination of water and wastewater.
16th ed. Washington, DC: American Public Health Association; 2005.
[29] Tchobanoglous G, Burton FL, Stensel HD. Metcalf and Eddy, Wastewater
Engineering: Treatment and Reuse, 4th ed. New York: McGraw-Hill Education;
2003.
[30] Wang XX, Wu YH, Zhang TY, Xu XQ, Dao GH, Hu HY. Simultaneous nitrogen,
phosphorous, and hardness removal from reverse osmosis concentrate by microalgae
cultivation. Water Res 2016; 94:215-24.
[31] Kumar M, Rao MS, Deka JP, Ramanathan AL, Kumar B. Integrated
hydrogeochemical, isotopic and geomorphological depiction of the groundwater
salinization in the aquifer system of Delhi, India. J Asian Earth Sci 2015; 111:936
47.
[32] Manenti DR, Soares PA, Módenes AN, Espinoza-Quiñones FR, Boaventura RAR,
Bergamasco R, Vilar VJP. Insights into solar photo-Fenton process using iron(III)-
organic ligand complexes applied to real textile wastewater treatment. Chem Eng J
2015; 266:203-12.
[33] Bustillo-Lecompte CF, Ghafoori S, Mehrvar M. Photochemical degradation of an
actual slaughterhouse wastewater by continuous UV/H2O2 photoreactor with
recycle. J Environ Chem Eng 2016; 4:719-32.
[34] Simonenko E, Gomonov A, Rolle N, Molodkina L. Modeling of H2O2 and UV
Oxidation of Organic Pollutants at Wastewater Post-treatment. Procedia Eng 2015;
117:337-44.
[35] De la Cruz N, Esquius L, Grandjean D, Magnet A, Tungler A, de Alencastro LF,
Pulgarín C. Degradation of emergent contaminants by UV, UV/H2O2 and neutral
Perla Tatiana Almazán Sánchez 98
“Tratamientos avanzados para la remoción de un colorante de origen textil”
photo-Fenton at pilot scale in a domestic wastewater treatment plant. Water Res
2013, 47:5836-45.
[36] Brillas E, Banos MA, Camps S, Arias C, Cabot PL, Garrido JA, Rodriguez R.M.
Catalytic effect of Fe2+, Cu2+ and UVA light on the electrochemical degradation of
nitrobenzene using an oxygen-diffusion cathode. New J Chem 2004; 28:314-22.
[37] De la Cruz N, Giménez J, Esplugas S, Grandjean D, de Alencastro LF, Pulgarín C.
Degradation of 32 emergent contaminants by UV and neutral photo-Fenton in
domestic wastewater effluent previously treated by activated sludge. Water Res
2012; 46:1947-57.
[38] Chen Q, Wu P, Li Y, Zhu N, Dang Z. Heterogeneous photo-Fenton photodegradation
of reactive brilliant orange X-GN over iron-pillared montmorillonite under visible
irradiation. J Hazard Mater 2009; 168:901-8.
[39] Dias FF, Oliveira AAS, Arcanjo AP, Moura FCC, Pacheco JGA. Residue-based iron
catalyst for the degradation of textile dye via heterogeneous photo-Fenton. Appl
Catal B-Environ 2016; 186:136-42.
[40] Al-Kahtani AA, Abou Taleb MF. Photocatalytic degradation of Maxilon C.I. basic
dye using CS/CoFe2O4/GONCs as a heterogeneous photo-Fenton catalyst prepared
by gamma irradiation. J Hazard Mater 2016; 309:10-9.
[41] Kwon M, Kim S, Yoon Y, Jung Y, Hwang TM, Lee J, Kang JW. Comparative
evaluation of ibuprofen removal by UV/H2O2 and UV/S2O82- processes for
wastewater treatment. Chem Eng J 2015; 269:379-90.
[42] Cotton FA, Wilkinson G. Química Inorgánica Avanzada (Advanced Inorganic
Chemistry), 4th ed. México: Limusa 2006.
[43] Almazán-Sánchez PT, Linares-Hernández I, Solache-Ríos MJ, Martínez-Miranda V.
Textile Wastewater Treatment Using Iron-Modified Clay and Copper-Modified
Carbon in Batch and Column Systems. Water Air Soil Poll 2016, 227:1-14.
[44] Qu R, Xu B, Meng L, Wang L, Wang Z. Ozonation of indigo enhanced by
carboxylated carbon nanotubes: Performance optimization, degradation products,
reaction mechanism and toxicity evaluation. Water Res 2015; 68:316-27.
Perla Tatiana Almazán Sánchez 99
“Tratamientos avanzados para la remoción de un colorante de origen textil”
6. DISCUSIÓN DE
RESULTADOS
Perla Tatiana Almazán Sánchez 100
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
6. DISCUSIÓN DE RESULTADOS
En este trabajo, se evaluó la remoción de un colorante de origen textil en solución
acuosa y de un efluente textil proveniente de una lavandería de acabados de prendas de
mezclilla, mediante los tratamientos de adsorción y oxidación avanzada por foto-Fenton
heterogéneo y foto-Fenton heterogéneo solar.
El colorante en estudio y el agua residual se obtuvieron de una lavandería de
acabados de prenda de mezclilla ubicada en el municipio de Almoloya del Río, Estado de
México. La caracterización del colorante por espectrofotometría de infrarrojo y
ultravioleta-visible, mostró la presencia de las bandas correspondientes a grupos amino,
alquenos, hidroxilo y aromáticos; el espectro obtenido se comparó con un estándar de
trisulfonato potásico de índigo y se observaron las mismas bandas que el colorante en
estudio, por lo que se trabajó con un colorante de tipo indigoide. En el estudio por
espectrofotometría UV-Vis, se obtuvo la banda de máxima absorción en la región visible
del espectro electromagnético a 591 nm. Por otro lado, se realizaron dos muestreos del
agua residual textil en estudio, presentado valores de pH de 6.84 y 6.86, la demanda
química de oxígeno (DQO) fue de 344 y 539 mg/L, la demanda bioquímica de oxígeno de
91.91 y 121.91 mg/L, el carbono orgánico total (COT) de 85 y 417 mg/L; el color de 330
y 642 unidades Pt-Co. El índice de biodegradabilidad (r) (r=DBO5/DQO) de esta agua
residual fue de 0.27 y 0.23 (promedio 0.25), indicando la presencia de materia orgánica no
biodegradable, limitando su tratamiento por procesos biológicos (Meltcalf y Eddy, 2003).
La concentración de fósforo total fue de 93.7 mg/L, superando tres veces el límite máximo
permisible que establece la NOM-001-SEMARNAT-1996 (30 mg/L) para descarga de
aguas residuales a cuerpos de agua, ocasionando problemas de eutrofización en los
sistemas acuáticos.
Los materiales seleccionados para llevar a cabo la remoción del colorante de
soluciones acuosas y del agua residual de origen textil fueron una arcilla montmorillonita
y un carbón activado, mismos que fueron modificados electroquímicamente (Teutli-
Sequeira et al., 2013) empleando electrodos de hierro y cobre; inicialmente se propuso
Perla Tatiana Almazán Sánchez 101
“Tratamientos avanzados para la remoción de un colorante de origen textil”
efectuar la modificación a valores de pH de 2 variando la concentración del metal fijado
en el material (0.25, 0.50 y 0.75 g), esto se logró aplicando diferentes tiempos de
modificación, mismos que fueron calculados con la ley de Faraday, para hierro fueron de
43, 87 y 130 min y para cobre de 25, 51 y 76 min. Sin embargo al realizar la caracterización
de los materiales se encontró que el único metal que fue fijado en condiciones ácidas fue
el cobre en el carbón activado (con un contenido del 12%) a un tiempo de modificación de
76 min, por lo que se realizó la modificación de la arcilla a valores de pH 7 para poder
promover la fijación del metal en el adsorbente, y en el caso del carbón se modificó con
Fe y Cu sin ajustar el valor del pH del sistema, que al final del tratamiento fue de 10. Las
muestras modificadas a pH 7 (arcillas) y sin controlar el valor del pH (carbón) fueron
nuevamente caracterizadas indicando la presencia del metal en un porcentaje de 5% y 10%
de Fe y Cu respectivamente en las arcillas (Mt-Fe-7 y Mt-Cu-7), mientras que para el
carbón modificado fue de 15% y 1.6% de Fe y Cu respectivamente (AC-Fe y AC-Cu). Los
materiales en los que se logró fijar la mayor concentración de Fe y Cu fueron
caracterizados por microscopía electrónica de barrido (MEB) donde no se observó un
cambio en su morfología; el análisis por difracción de rayos X (DRX) de las arcillas,
mostró cambios en la intensidad de los picos del difractograma indicando que no hubo un
cambio en la cristalinidad de las arcillas modificadas; se identificaron como componentes
principales a la montmorillonita, muscovita y cuarzo. El análisis de área específica BET
mostró para la arcilla natural (Mt-KSF), la arcilla modificada con hierro (Mt-Fe-7) y cobre
(Mt-Cu-7), el carbón natural (AC-N) y modificado con cobre (AC-Cu-2) valores de 5.14,
131.3, 78.44, y 647.61 y 654.85 m2/g respectivamente, observándose una mayor área
específica en el material modificado que en el natural, esto debido a la presencia de Fe o
Cu, metales de transición que promueven la presencia de sitios activos en los materiales
modificados.
Por otro lado, se determinó el punto de carga cero (pHpzc) de los materiales
naturales y modificados seleccionados. Para Mt-KSF, M-Fe-7, Mt-Cu-7, AC-N y AC-Cu-
2 se obtuvieron valores de pHpzc de 2.86, 6.82, 7.445, 10.22 y 7.23 respectivamente; la
superficie del adsorbente está cargada negativamente a valores de pH mayores al valor del
punto de carga cero y positiva a valores de pH menores al pHpzc; estos resultados
Perla Tatiana Almazán Sánchez 102
“Tratamientos avanzados para la remoción de un colorante de origen textil”
presentaron una gran ventaja en la remoción del colorante en estudio a valores de pH
menores al punto de carga cero, debido a que en su estructura están presentes los grupos
sulfonatos que tienen carga negativa.
Las pruebas de adsorción del color a diferentes valores de pH (2-10) de la solución
acuosa del colorante trisulfonato potásico de índigo (azul índigo) se realizaron con los
materiales modificados al máximo tiempo de modificación (Fe=130 min, Cu= 76 min) a
pH 2, pH 7 y sin controlar el pH del sistema. Los resultados mostraron que los materiales
más eficientes en la remoción del colorante fueron las muestras de arcilla modificadas con
Fe y Cu a pH 7 (Mt-Fe-7 y Mt-Cu-7) y para el carbón activado el modificado con cobre a
pH 2 (AC-Cu-2), donde las mejores condiciones de pH para remover el colorante fueron
4-10, con eficiencias de remoción superiores al 90%. De acuerdo con Al-Degs et al., (2008)
la adsorción de colorantes aniónicos como el azul índigo puede ser mayor a valores de pH
ácidos ya que la superficie del adsorbente está cargada positivamente atraé a las moléculas
cargadas negativamente en donde un mecanismo de adsorción por interacciones
electrostáticas se está llevando acabo, sin embargo el pH no es el único factor que favorece
la adsorción de colorantes sino que los grupos funcionales presentes en el adsorbente y la
composición inorgánica del disolvente también son características importantes que afectan
la adsorción (Cooney, 1999).
Las cinéticas de adsorción del colorante mostraron un tiempo de equilibrio para
Mt-KSF de 5 min, de 48 h para Mt-Fe-7 y Mt-Cu-7, de 72 h para AC-Cu-2 y para AC-N
de 96 h. De acuerdo con las constantes obtenidas al aplicar los modelos cinéticos de
adsorción, se observó que los datos se ajustaron mejor al modelo de pseudo-segundo orden
y Elovich con un R2 > 0.87, sugiriendo como posible mecanismo de remoción del colorante
en solución acuosa a la quimisorción (Ho, 2006). Cottet et al. (2014) utilizó la arcilla
montmorillonita modificada con óxido de hierro para remover azul de metileno de
soluciones acuosas, obteniendo un valor de k2 de 16.01x104 g min/mg mientras que para
remover el azul índigo de la solución con Mt-Fe-7 la constante fue de 0.075 g min/mg.
En cuanto a las isotermas de adsorción, los datos obtenidos con Mt-KSF, Mt-Fe-7,
AC-N y AC-Cu-2 mostraron un valor de R2 ligeramente mayor para el modelo de
Freundlich indicando la heterogeneidad de los materiales adsorbentes empleados y una
Perla Tatiana Almazán Sánchez 103
“Tratamientos avanzados para la remoción de un colorante de origen textil”
sorción en multicapa (Freundlich, 1906), en el caso de Mt-Cu-7 los datos se ajustaron al
modelo de Langmuir, con una capacidad máxima de adsorción de 2.62 mg/g. Las pruebas
de adsorción indicaron que la arcilla natural (Mt-KSF) fue más eficiente en la remoción
del colorante en solución acuosa (100%), seguido del carbón modificado con cobre (AC-
Cu-2) con una eficiencia del 98%, considerando un tiempo de contacto de 5 min y 48 h
respectivamente. Mahmoodi et-al. (2011) utilizaron carbón activado para adsorber el
colorante azul 78 obteniendo una constante de Freundlich (KF) de 23.85
((mg/g)(L/mg)1/n), mientras que la constante obtenida en este trabajo para AC-N y AC-
Cu-2 fue de 1.351 y 1.635 ((mg/g)(L/mg)1/n), respectivamente. Por otro lado, DiazGomez-
Treviño et-al. (2013), evaluaron la adsorción de amarillo remazol con la arcilla
montmorillonita modificada con FeCl3 obteniendo constantes de KF de 13.37
((mg/g)(L/mg)1/n), dicho valor fue muy similar al obtenido con Mt-KSF
(14.284((mg/g)(L/mg)1/n)) mientras que para Mt-Fe-7 fue de 0.28 ((mg/g)(L/mg)1/n)
Se evaluó en el proceso de adsorción la demanda química de oxígeno (DQO), color
y carbono orgánico total (COT) presentes en el agua residual textil utilizando los cuatro
mejores materiales (Mt-KSF, Mt-Fe-7, AC-N y AC-Cu-2). La arcilla natural fue más
eficiente en la remoción de color (90%), con una capacidad de adsorción de 50 U PtCo,
mientras que para la DQO y el COT se observó una desorción, con eficiencias de remoción
de 32% y 18% respectivamente, a un tiempo de contacto de 72 h. Para Mt-Fe-7, AC-N y
AC-Cu-2, el tiempo de equilibrio obtenido para los tres parámetros evaluados fue de 48 h,
y en el caso del color, Mt-Fe-7 fue más eficiente con una capacidad de adsorción de 47 U
PtCo/g seguido de AC-N (37 U PtCo/g). En el tratamiento del agua residual textil, el AC-
Cu-2 fue el material menos eficiente en la remoción de los parámetros en estudio, debido
posiblemente a la baja afinidad del material con la materia orgánica presente en la muestra
de agua o a que existe una competencia entre el colorante y la materia inorgánica como
fosfatos, sulfatos y cloruros, los cuales forman compuestos de coordinación con metales
de transición como hierro y cobre. De acuerdo con los datos obtenidos por los modelos
cinéticos de adsorción aplicados, hubo un mejor ajuste para el modelo de Elovich,
indicando una quimisorción, mientras que los datos de isotermas de color se ajustaron al
modelo de Freundlich.
Perla Tatiana Almazán Sánchez 104
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Comparando los materiales usados, se observó que AC-Cu-2 fue más eficiente en
la remoción del colorante en solución acuosa que AC-N, mientras que para el agua residual
hubo un comportamiento opuesto, pues el carbón modificado resultó ser menos eficiente
que los otros materiales aplicados; esto indica, cómo se mencionó anteriormente, que hay
posiblemente una débil afinidad de la materia orgánica con AC-Cu-2 o la competencia con
las especies presentes en la muestra de agua residual lo que disminuyó su eficiencia en el
tratamiento del agua.
Los ciclos de adsorción-regeneración realizados con peróxido de hidrógeno en
presencia y ausencia de luz solar por el proceso de Fenton y foto-Fenton heterogéneo,
mostraron que para las soluciones acuosas del colorante hubo mejores resultados cuando
el material se regeneró con luz solar, donde Mt-Fe-7, AC-N y Mt-Cu-7 mantuvieron su
eficiencia de remoción durante los cuatro ciclos evaluados, mientras que la remoción del
colorante con Mt-KSF y AC-Cu-2 disminuyó. Aunque Mt-KSF disminuye su remoción, a
partir del ciclo 2 se mantiene la eficiencia en un 30% aproximadamente; mientras que para
Mt-Fe-7 las eficiencias son superiores al 85%, mostrando que la modificación de la arcilla
promueve su reúso en varios ciclos, desventaja que presenta la arcilla natural, que sólo es
eficiente para remover el color durante el primer ciclo.
En el caso de los ciclos de regeneración aplicados con el agua residual, se observó
que en general los materiales mantuvieron su eficiencia en la remoción de los parámetros
evaluados, sin embargo hubo un comportamiento opuesto a los resultados obtenidos con
las soluciones acuosas del colorante, pues los mejores resultados se obtuvieron en la
regeneración del material sin luz solar, esto debido posiblemente a que parte de la materia
orgánica e inorgánica no fue removida durante el proceso de regeneración de los
adsorbentes.
Las columnas de adsorción realizadas con el agua residual en estudio, mostraron
que a una concentración de 100 U PtCo y 15 mg COT/L, los mayores tiempos de ruptura
de color se obtuvieron con Mt-Fe-7 (160 min) con 3 g de adsorbente, mientras que para
COT fue con AC-N (180 min) con 7 g. Se observó de manera general que al ir aumentando
la dosis del adsorbente el tiempo de ruptura y la capacidad de adsorción incrementa, debido
a una mayor zona de transferencia de masa. Las curvas de ruptura revelaron que las
Perla Tatiana Almazán Sánchez 105
“Tratamientos avanzados para la remoción de un colorante de origen textil”
columnas realizadas con el carbón natural sin alcanzar el tiempo de saturación en el sistema
en continuo. Al evaluar los modelos de Thomas, Yoon-Nelson y Bohart-Adams se observó
que Mt-KSF y Mt-Fe-7 tuvieron las mayores capacidades de adsorción de color (23 y 19
U PtCo/g) y COT (3 y 10 mg COT/L) las presentaron, así como los coeficientes de
correlación (R2>0.80).
Los materiales modificados fueron utilizados para dos tratamientos, en el proceso
de adsorción y para el proceso de oxidación avanzada por Fenton y foto-Fenton.
Para llevar a cabo el proceso de foto-Fenton, se procedió a construir un
concentrador parabólico compuesto en dos dimensiones (CPC-2D), para promover el uso
de energías alternativas como la solar y su aplicación en procesos sustentable en el
tratamiento de las aguas residuales, mediante la concentración de radiación UV para
promover el proceso de oxidación del colorante presente en el agua residual en estudio. Al
llevar acabo la medición de la radiación UV-A y UV-B dentro y fuera de la línea de
concentración del CPC-2D se observó que la radiación concentrada fue de 54.29±0.71 y
1.65±0.37 W/m2 respectivamente, un 34% y 75 % de mayor radiación concentrada con
respecto a la no concentrada, indicando que el CPC-2D si permite concentrar radiación
UV.
Se evaluó el proceso de Fenton heterogéneo sin radiación UV con Mt-Fe-7 y se
observó sólo un 6% de remoción del colorante en solución acuosa. De acuerdo con los
resultados obtenidos, las soluciones acuosas del colorante y del agua residuales al ser
tratadas con 1.5 g de AC-Cu-2, 0.5 M de H2O2 y radiación UV mostraron una mejor
eficiencia en la eliminación del color, para las soluciones acuosas a las 2 h con una
eficiencia del 99%; mientras que para el agua residual el tiempo de tratamiento fue de 4 h
con una remoción del color del 93%; al utilizar la arcilla modificada con hierro (Mt-Fe-7)
y 0.5 M de H2O2, la eficiencia en la eliminación de color en las soluciones acuosas y el
agua residual fue de 98% y 90% a un tiempo de 3.5 h y 4.0 h respectivamente; se observa
el importante papel que juega la radiación UV en el proceso de oxidación. Al analizar por
infrarrojo las muestras antes y después del tratamiento por foto-Fenton heterogéneo, se
observó un cambio en el espectro del agua tratada, indicando que la materia orgánica se
oxidó durante el proceso de foto-Fenton. En el caso del agua residual textil tratada, los
Perla Tatiana Almazán Sánchez 106
“Tratamientos avanzados para la remoción de un colorante de origen textil”
espectros obtenidos al aplicar los catalizadores usados (Mt-Fe-7 y AC-Cu-2) fueron muy
similares, indicando que ambos catalizadores oxidan de igual forma la materia orgánica
presente en el agua residual, sólo hay una diferencia en la eficiencia de remoción, ya que
el cobre resultó ser el más eficiente, indicando que este metal puede ser utilizado al igual
que hierro para efectuar el proceso de oxidación por Fenton. El proceso de Fenton se lleva
a cabo a pH 2.8 (Chen et al., 2009) para promover la formación del radical hidroxilo, sin
embargo el proceso de foto-Fenton heterogéneo se realizó a valores de pH de 7 y 6.86 para
las soluciones acuosas y el agua residual y después del tratamiento el pH fue de 6.82 y
6.75 respectivamente, siendo un factor importante en la descarga de aguas residuales. Dias
et-al. (2016) aplicaron el proceso de foto-Fenton heterogéneo para oxidar Negro reactivo
5 usado un residuo obtenido de la industria del aluminio rico en hierro, donde sus mejores
eficiencias se alcanzaron a pH 3, mientras que Al-Kahtani et-al. (2016) sintetizaron un
composito de quitosano, ferrita de cobalto y oxido de grafeno para usarlo en el proceso de
foto-Fenton heterogéneo y eliminar Maxilon C.I. del agua a un pH de 9.5. Se aprecia que
el pH es un factor importante en la oxidación de colorantes.
Perla Tatiana Almazán Sánchez 107
“Tratamientos avanzados para la remoción de un colorante de origen textil”
7. CONCLUSIONES
Perla Tatiana Almazán Sánchez 108
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
7. CONCLUSIONES
El tratamiento de soluciones acuosas de un colorante y de un agua residual
provenientes de una lavandería de acabados de prendas de mezclilla, fue logrado
empleando una arcilla y un carbón activado modificados electroquímicamente con hierro
y cobre, aplicando los procesos de adsorción y oxidación avanzada por foto-Fenton
heterogéneo solar.
El pH fue un factor importante en la modificación electroquímica de los materiales,
pues bajo condiciones ácidas sólo el cobre fue fijado en el carbón activado, mientras que
para las muestras de arcilla el pH óptimo fue 7. Las técnicas de microscopía electrónica de
barrido, difracción de rayos X (DRX) y área específica BET, permitieron caracterizar los
materiales y conocer las mejores condiciones de modificación para fijar el Fe y el Cu en la
arcilla y el carbón natural.
La caracterización del colorante por espectrofotometría de infrarrojo, mostró la
presencia de grupos funcionales de aminas, aromáticos, alquenos e hidroxilo; y de acuerdo
con la comparación realizada con un estándar, se encontró que es el trisulfonato potásico
de índigo (azul ínidigo).
El agua residual en estudio presentó una baja biodegradabilidad y un alto contenido
de fósforo, por lo que es importante implementar un tratamiento que permita disminuir los
efectos adversos que pudiera ocasionar en el ambiente.
El efecto del pH en la remoción del colorante en soluciones acuosas mostró que
Mt-KSF, Mt-Fe-7, Mt-Cu-7 y AC-Cu-2 fueron muy eficientes en un intervalo de pH de 4
10, siendo la arcilla natural la que presentó mejores porcentajes de remoción, superiores al
85%. Los datos obtenidos de las cinéticas de adsorción del colorante en solución acuosa y
de los parámetros en estudio evaluados en el agua residual (color, DQO y COT), se
ajustaron al modelo pseudo-segundo orden y Elovich indicando como posible mecanismo
de remoción a la quimisorción; mientras que las isotermas de adsorción se ajustaron al
modelo de Freundlich, indicando la heterogeneidad de los adsorbentes y una sorción en
multicapa.
Perla Tatiana Almazán Sánchez 109
“Tratamientos avanzados para la remoción de un colorante de origen textil”
El carbón modificado con cobre (AC-Cu-2) mostró excelentes eficiencias de
remoción del colorante en solución acuosa, sin embargo no se observó el mismo
comportamiento al aplicarlo en el agua residual, indicando la gran influencia de la
composición orgánica e inorgánica en la muestra de agua residual textil sobre la adsorción
de los parámetros evaluados (color, COT y DQO).
Los ciclos de adsorción-regeneración evaluados con la solución acuosa del
colorante para Mt-Fe-7, Mt-Cu-7 y AC-N mantuvieron su eficiencia de remoción cuando
se aplicó luz solar, mientras que para Mt-KSF y AC-Cu-2 la eficiencia de remoción
disminuyó; en este caso, la arcilla modificada con hierro presentó las mejores eficiencias
de remoción. Los ciclos de regeneración con el agua residual mostraron un
comportamiento similar durante los ciclos evaluados (Mt-KSF, Mt-Fe-7, AC-N y AC-Cu-
2), sin embargo, las mejores eficiencias de remoción se apreciaron cuando los materiales
se regeneraron en ausencia de luz solar, caso contrario a los resultados obtenidos con las
soluciones acuosas.
Las columnas de adsorción utilizando Mt-KSF, Mt-Fe-7 y AC-N mostraron un
mejor ajuste con el modelo de Thomas y Yoon-Nelson, mientras que los mayores tiempos
de ruptura para color y COT se obtuvieron con Mt-Fe-7, con tiempos de ruptura del color
y COT, de 160 y 180 min y capacidades de adsorción de 19 U PtCo/g y 10 mg COT/g.
El uso y la aplicación de energías alternativas como la energía solar, permite aplicar
procesos más sustentables para el tratamiento de aguas residuales. Los concentradores
solares CPC-2D son dispositivos que permiten concentrar radiación UV y utilizarla en el
proceso de foto-Fenton heterogéneo.
Al utilizar una dosis del catalizador de 1.5 g y 0.5 M de H2O2 en presencia de
radiación UV, el carbón modificado con cobre (AC-Cu-2) y la arcilla modificada con
hierro (Mt-Fe-7) tuvieron eficiencias de remoción muy similares (99% y 98%) con tiempos
de tratamiento de 2.0 y 3.5 h respectivamente, siendo el cobre el que mostró un menor
tiempo en la oxidación del colorante, mientras que para el agua residual la eficiencia de
remoción fue de 93% y 90% con AC-Cu-2 y Mt-Fe-7 respectivamente. La radiación UV
Perla Tatiana Almazán Sánchez 110
“Tratamientos avanzados para la remoción de un colorante de origen textil”
mostró un papel importante en la oxidación del colorante y la materia orgánica presente en
las soluciones acuosas y el agua residual textil.
Perla Tatiana Almazán Sánchez 111
“Tratamientos avanzados para la remoción de un colorante de origen textil”
8. SUGERENCIAS
Perla Tatiana Almazán Sánchez 112
“Tratamientos avanzados para la remoción de un colorante de origen textil”
8. Sugerencias
a) El agua residual generada por lavanderías de acabados de prendas de mezclilla debe
ser tratada antes de ser descargarla a cuerpos de agua, debido a la baja
biodegradabilidad de la materia orgánica y al alto contenido de fosfatos que
presenta y que podría ocasionar daños severos al ambiente.
b) Evaluar la adsorción de la materia inorgánica como fosfatos, sulfatos, cloruros con
el carbón modificado con cobre, pues es posible que debido a una competencia
entre materia orgánica e inorgánica el colorante no fue removido del agua residual
textil.
c) Realizar estudios de columnas con doble lecho, utilizando la arcilla natural y
modificada, ya que la primera fue muy eficiente para remover el color y la segunda
para remover materia orgánica presente en el agua residual.
d) Analizar los subproductos de degradación durante la oxidación del colorante en el
proceso de foto-Fenton heterogéneo.
e) Realizar más ciclos de adsorción-regeneración con la arcilla modificada con hierro
para evaluar el máximo de ciclos que puede funcionar como adsorbente.
f) Realizar pruebas de toxicidad al agua después de los tratamientos.
Perla Tatiana Almazán Sánchez 113
“Tratamientos avanzados para la remoción de un colorante de origen textil”
9. PRODUCTOS
Perla Tatiana Almazán Sánchez 114
“Tratamientos avanzados para la remoción de un colorante de origen textil”
9.1 Listado de productos obtenidos
Artículos de
investigación de
este proyecto
• Adsorption-regeneration by heterogeneous Fenton process using
modified carbon and clay materials for removal of indigo blue.
Environmental Technology (Publicado).
• Textile wastewater treatment using iron modified clay and copper
modified carbon in batch and columns systems. Water Air and Soil
Pollution (Publicado).
• Treatment of textile industrial wastewater by solar photo-Fenton
powered by CPC-2D. Fuel (Enviado).
Otras
colaboraciones
en artículos
• Soft drink wastewater treatment by electrocoagulation-
electrooxidation processes. Ivonne Linares Hernández, Carlos
Barrera Díaz, Mario Valdés Cerecero, Perla Tatiana Almazán
Sánchez, Monserrat Castañeda Juárez, Violeta Lugo Lugo.
Environmental Technology (Publicado).
• Industrial wastewater treatment by electrocoagulation-
electrooxidation processes powered by solar cells. Alfredo García-
García, Verónica Martínez-Miranda, Iván G. Martínez-
Cienfuegos, Perla Tatiana Almazán-Sánchez, Monserrat
Castañeda-Juárez, Ivonne Linares-Hernández. Fuel (Publicado)
Capítulos de
libro
• Efecto del pH en la adsorción de un colorante textil usando
materiales naturales y modificados. Ciencias del Agua: Perspectiva
desde la academia 2014. SIyEA UAEM. (Aceptado).
• Procesos de oxidación avanzada para la remoción de materia
orgánica en las aguas residuales. Ciencias del Agua: Perspectiva
desde la academia 2014. SIyEA UAEM. (Aceptado).
Congresos
• X Simposio Ciencia Joven
Lugar: Facultad de Ciencias y Tecnologías Químicas de la
Universidad de Castilla-La Mancha. Ciudad Real, España, 8-10
de junio de 2016 (Asistente).
Perla Tatiana Almazán Sánchez 115
“Tratamientos avanzados para la remoción de un colorante de origen textil”
• Bridging the Americas: Promoting global solutions of local
landfill problems through student service and learning, del 4 al 8
de abril de 2016, Toluca, Estado de México. (Participante).
• International Mexican Congress of Chemical Engineer, del 5 al 9
de junio de 2016, Querétaro, Querétaro, México. Treatment of
Textile Industrial Wastewater by Solar Photo-Fenton Powered by
CPC-2D (Cartel).
• Instituto Nacional de Investigaciones Nucleares. Sindicato Único
de Trabajadores de la Industria Nuclear. Congreso Técnico
Científico, del 8 al 10 de Diciembre de 2015, Ocoyoacac, México.
Tratamiento de un agua residual proveniente de la industria textil
empleando adsorbentes modificados (Cartel).
• XXX Congreso Nacional de la Sociedad Mexicana de
Electroquímica y el 8th Meeting of the Mexican Section of
Electrochemistry Society, del 07 al 12 de Junio de 2015. Boca del
Río Veracruz. Modificación electroquímica de una arcilla y de un
carbón usados en la remoción de colorantes (Cartel).
• Instituto Nacional de Investigaciones Nucleares. Sindicato Único
de Trabajadores de la Industria Nuclear. Congreso Técnico
Científico, del 2 al 4 de Diciembre de 2014, Ocoyoacac, México.
Remoción de azul índigo empleando materiales naturales y
modificados (Cartel).
• Tecnológico de Estudios Superiores de Jocotitlán. 1 de Diciembre
de 2014. Jocotitlán México II Simposium de Ciencias
Ambientales. Uso de materiales naturales y modificados para la
remoción de colorantes. (Oral).
• 6° Encuentro Universitario del Agua, 10 y 11 de Septiembre de
2014. Torre de Ingeniería, CU-UNAM. Remoción de un colorante
indigoide usando una arcilla y carbón modificados (Cartel).
• 6to Curso-Taller “Temas actuales en Ciencias del Agua”, 14 y 15
de Noviembre de 2013. Centro Interamericano de Recursos del
Agua. “Tratamiento de un residuo acuoso proveniente de una
Perla Tatiana Almazán Sánchez 116
“Tratamientos avanzados para la remoción de un colorante de origen textil”
industria química productora de láminas de acrílico empleando un
carbón activado natural y modificado” (Ponente).
• Lugar: Universidad de Castilla-La Mancha, Departamento de
Ingeniería Química, Ciudad Real, España. del 10 de abril de 2016
al 07 de julio de 2016. Investigador: Dr. Manuel Andrés Rodrigo
Estancias de Rodrigo.
investigación • Lugar: Instituto Nacional de Investigaciones Nucleares (ININ).
Departamento de Química. Ocoyoacac, México. del 03 de Marzo
de 2014 al 03 de Marzo de 2016. Investigador: Dr. Marcos José
Solache Ríos.
• Comprensión de conversación
Lugar: Centro Interamericano de Recursos del Agua, Toluca,
México, 8 de febrero al 7 de abril de 2016. Duración: 30 horas.
Impartido por: Sergio Galeana Estrada
• Estadística aplicada a las ciencias del agua
Lugar: Centro Interamericano de Recursos del Agua, Toluca,
México, 23 de septiembre al 21 de octubre de 2015. Duración: 25
horas.
Impartido por: Dr. Víctor Manuel Pérez Ilafor
• Curso-Taller para la elaboración de guías pedagógicas.
Cursos
•
Lugar: Facultad de Ingeniería, UAEMÉX, Toluca, México, 06-10
julio de 2015.
Duración: 25 horas.
Impartido por: M. en I. Armando Herrera Barrera.
Cálculo de distribución de corriente secundaria.
Lugar: Centro Conjunto de Investigación en Química Sustentable,
Toluca, México, 9-10 de enero de 2014. Duración: 10 horas.
Impartido por: Dr. Israel Rodríguez Torres.
• Redacción de textos científicos.
Lugar: Centro Interamericano de Recursos del Agua, Toluca,
México, 1-29 de Octubre de 2013. Duración: 25 horas.
Impartido por: Dr. Lenin Martell Gámez
Perla Tatiana Almazán Sánchez 117
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Tesis de
Licenciatura
co-dirigidas
• Licenciatura en Química: Pre-tratamiento de un agua residual
industrial alcalina empleando zeolita clinoptilolita para
incrementar la eficiencia en la oxidación de la materia orgánica.
Alumna: Rosa Elia Victoria Salinas (Titulada).
• Ingeniería Mecánica: Implementación de un concentrador solar
parabólico compuesto en el tratamiento de aguas residuales
textiles. Alumno: Paul William Marín (Protocolo aceptado).
Docencia
• Clase: Control Ambiental (3 h/semana/mes). Nivel: Licenciatura
(Ingeniería Mecánica). Lugar: Facultad de Ingeniería. Universidad
Autónoma del Estado de México. Periodo: Febrero-Diciembre de
2015.
Perla Tatiana Almazán Sánchez 118
“Tratamientos avanzados para la remoción de un colorante de origen textil”
9.2 Documentos probatorios
Taylor & Francis
Environmental Technology
ISSN: 0959-3330 (Print) 1479-487X (Online) Journal homepage: http://www.tandfonline.com/loi/tent20
Adsorption-regeneration by heterogeneous Fenton process using modified carbon and clay materials for removal of indigo blue
Perla Tatiana Almazán-Sánchez, Marcos J. Solache-Ríos, Ivonne Linares- Hernández & Verónica Martinez-Miranda
To cite this article: Perla Tatiana Almazán-Sánchez, Marcos J. Solache-Ríos, Ivonne Linares- Hernández & Verónica Martinez-Miranda (2016): Adsorption-regeneration by heterogeneous Fenton process using modified carbon and clay materials for removal of Indigo blue. Environmental Technology, DOI: 10.1080/09593330.2015.1133718
To link to this article: http://dx.dol.Org/10.1080/09593330.2015.1133718
Full Terms & Conditions of access and use can be found at http://www.tandfonline.com/action/jou rnallnformation?journalCode=tent20
Perla Tatiana Almazán Sánchez 119
Tratamientos avanzados para la remoción de un colorante de origen textil”
Water Air Soil Pollut (2016) 227:100DOI 10.1007/s 11270-016-2801-7 1) CrossMark
Textile Wastewater Treatment Using Iron-Modified Clay and Copper-Modified Carbon in Batch and Column Systems
Perla Tatiana Almazán-Sánchez •Ivonne Linares-Hernández • Marcos J. Solache-Ríos • Verónica Martinez-Miranda
Received: 12 November 2015 /Accepted: 29 February 2016 © Springer International Publishing Switzerland 2016
Abstract Textile wastewater was treated by adsorption in batch and column systems using electrochemically modified montmorillonite clay and activated carbon. Textile wastewater was obtained from a denim manufacturing process; according to the characterization of wastewater, non-biodegradable organic matter was found and it limits the application of biological treatments, and then an alternative method was evaluated. The adsorption process was performed with natural and modified materials; iron-modified montmorillonite was prepared at pH 7 using iron electrodes and activated carbon was treated with copper electrodes at pH 2, and 10-12 % of iron and copper respectively were found in the modified materials. Adsorption kinetics and isotherms of chemical oxygen demand (COD), color, and total organic carbon (TOC) were evaluated; the adsorption capacities for color were 50, 37, and 44 U PtCo/g for natural clay, activated carbon, and iron-modified clay, respectively. Adsorption kinetics of COD, color, and TOC data were best adjusted to Elovich model and isotherms data to Freundlich model, indicating
chemisorption on heterogeneous materials. The regeneration of materials was performed in the presence and absence of hydrogen peroxide. Continuous systems were evaluated for color and TOC. Fe-modified clay was the best adsorbent, and data were best adjusted to Thomas and Yoon-Nelson models.
Keywords Montmorillonite • Activated carbon • Electrochemical modification • Fixed bed column
P. T. Almazán-Sánchez • M. J. Solache-Ríos (IS!)Departamento de Química, Instituto Nacional de Investigaciones Nucleares (ININ), Carretera México-Toluca S/N, La Marquesa, C.P. 52750 Ocoyoacac, Estado de México, Mexico e-mail: marcos.solache@inin.gob.inx
P. T. Almazán-Sánchez ■ I. Linares-Hernández •V. Martíncz-MirandaCentro Interamericano de Recursos del Agua (CIRA), Facultad de Ingeniería, Unidad San Cayetano, Universidad Autónoma del Estado de México, Km.14.5, carretera Toluca-Atlacomulco, C.P. 50200 Toluca, Estado de México, Mexico
Published online: 08 March 2016
1 Introduction
Textile industry plays an important role in the world economy; the discharge of textile effluents to natural water bodies causes alterations in aquatic biological activities (Amin 2009) because dyes could be mutagenic and carcinogenic (Kadirvelu et al. 2003). This industry is one of the most polluting because of the large amounts of water, dyes, and chemical compounds used in the processes. Textile wastewater contains color and organic compounds with complex structures that are discharged in sewerages and surface waters (Butrón et al. 2007). Textile dyes are usually transformed to toxic aromatic amines, they absorb and reflect sunlight, avoiding the photosynthesis of aquatic plants, and they exhibit recalcitrant properties (Cañizares et al. 2006; Kadirvelu et al. 2003; Mesquita et al. 2012).
Textile industry is the fourth largest manufacture activity in Mexico; furthermore, it is one of the most important industries, because Mexico is the fourth
£) Springer
Perla Tatiana Almazán Sánchez 120
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Technology
Taylor & FrancisTaylor (.Francis Group
Environmental Technology
ISSN: 0959-3330 (Print) 1479-487X (Online) Journal homepage: http://www.tandfonline.com/loi/tent20
Soft drink wastewater treatment byelectrocoagulation-electrooxidation processes
Ivonne Linares Hernández, Carlos Barrera Díaz, Mario Valdés Cerecero, PerlaTatiana Almazán Sánchez, Monserrat Castañeda Juárez & Violeta Lugo Lugo
To cite this article: Ivonne Linares Hernández, Carlos Barrera Díaz, Mario Valdés Cerecero,Perla Tatiana Almazán Sánchez, Monserrat Castañeda Juárez & Violeta Lugo Lugo (2016): Softdrink wastewater treatment by electrocoagulatlon-electrooxldation processes, EnvironmentalTechnology, DOI: 10.1080/09593330.2016.1196740
To link to this article: http://dx.doi.org/10.1080/09593330.2016.1196740
Full Terms & Conditions of access and use can be found at http://www.tandfonline.com/action/journallnformation?journalCode=tent20
Perla Tatiana Almazán Sánchez 121
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fuel 149(2015)46-54
Contents lists available at ScienceDirect
Fuel
journal homepage: www.elsevier.com/locate/fuel
Industrial wastewater treatment by electrocoagulation-electrooxidation processes powered by solar cells
CrossMark
Alfredo García-García'1, Verónica Martinez-Mirandab. Iván G. Martinez-Cienfuegos3,Perla Tatiana Almazán-Sánchez b, Monserrat Castañeda-Juárez b, Ivonne Linares-Hernández b’* *J Facultad de Ingeniería de la Universidad Autónoma del Estado de México, Cerro de Coatepec s/n, Ciudad Universitaria, CP. 50100 Toluca, Estado de México, Mexico h Centro Interamericano de Recursos del Agua (CIRA), Universidad Autónoma del Estado de México. Facultad de Ingeniería, Unidad San Cayetano, km. 14.5 carretera. Toluca-Atlacomulco, C.P 50200 Toluca. Estado de México, Mexico
HIGHLIGHTS GRAPHICAL ABSTRACT
• The EC and EO achieved a TOC removal efficiency of 99%.
• The use of copper in EC stabilizes the system.
• The electrooxidation process (BDD/ Cu) promotes the demineralization of water.
• The electrooxidation is a clean process that avoids the C02 emissions.
• The solar cells supply sustainable energy to the electrochemical processes.
ARTICLE INFO ABSTRACT
Article history:Received 14 March 2014Received in revised form 16 September 2014 Accepted 22 September 2014 Available online 7 October 2014
Keywords: Electrocoagulation Electrooxidation Copper electrodes Boron-doped diamond Solar cells
The goal of this research was the elimination of the chemical oxygen demand (COD), total organic carbon (TOC), color, and turbidity from the industrial wastewater from an industrial park by applying electrocoagulation (EC) and electrooxidation (EO) processes powered by solar cells. The EC process was carried out in a batch monopolar electrochemical cell; copper was used for the anode and cathode electrodes, with an area of 0.00125 m2, and solar cells supplied the system with 1-3 A of current intensity. The COD reduction was 80% at pH 2 and 89% at pH 4. and a removal efficiency of 97% and 91% of color and turbidity, respectively, were achieved: however, TOC reduction achieved was only 48%. In order to improve the removal of TOC, an EO treatment was applied after the EC process. The EO was carried out in batch cells using a boron-doped diamond (BDD) anode and a copper cathode. The maximum removal efficiency was 70.26% of TOC and 99.7% of COD, with EC + EO processes. Color and turbidity removal were 100% and 95%, respectively. Aside from the strong oxidation capability of the hydroxyl radicals generated, the presence of active chlorine in the solution contributed to COD removal via indirect oxidation.
© 2014 Elsevier Ltd. All rights reserved.
* Corresponding author. Tel.: +52 (722) 2965550.E-mail address: ivonnelinaresl978@yahoo.com.mx (I. Linares-Hernández).
http://dx.doi.org/10.1016/j.fuel.2014.09.0800016-2361/© 2014 Elsevier Ltd. All rights reserved.
1. Introduction
Toluca-Lerma is the second most important industrial area of Mexico and has almost 300 companies that provide jobs, economic resources, and a better quality of life. Nevertheless, industrial
Perla Tatiana Almazán Sánchez 122
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 123
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 124
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 125
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 126
“Tratamientos avanzados para la remoción de un colorante de origen textil”
IMCCRE2016Querétaro, México, June 5-9,2016
The Organizing Committee of the
IMCCRE-2016
International-Mexican Congress on Chemical Reaction Engineering
Certifies thatP. W. Marin-Noriega, P. T. Almazán-Sánchez,
I. Linares-Hernández,1. G. Martínez-Cienfuegos,
M. J. Solache-Ríos, V. Martínez Miranda
Contributed with the poster paper Treatment of textile indaitrial wastewater by salar
photoJentoXihwtred by CPC-2D
Perla Tatiana Almazán Sánchez 127
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 128
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 129
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
El Instituto Nacional de Investigaciones Nucleares y el Sindicato Único de Trabajadores de la Industria Nuclear
otorgan el presente
Reconocimientoa:
Almazán-Sánchez P. I, Solache-Ríos M., Linares-HernándezI., Martínez-Miranda V.Por su participación con el trabajo:
Remoción de azul índigo usando materiales naturales y modificados.
ININ SUTIN
Perla Tatiana Almazán Sánchez 130
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 131
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 132
“Tratamientos avanzados para la remoción de un colorante de origen textil”
♦lUKSILIM] Prof. Dr. Manuel Andrés Rodrigo RodrigoFull Professor of Chemical Engineering
Ciudad Real, July 7th 2016
To whom it may concern
This is to certify that Ms. Perla Tatiana Almazán Sánchez, from the Universidad Autónoma del Estado de México, has joined the Electrochemical Engineering Lab of the Universidad de Castilla La Mancha from April 10th 2016 to July 7th 2016, period in which she has worked under my supervision.
In this training period, she has studied the treatment of soil polluted with pendimenthalin, coupling soil washing with electrochemical oxidation with diamond. She has obtained a great amount of experimental results, and she has done a good discussion of the main processes occurring in the system, which, for sure, will result in publications in highly cited journals.
Ms. Almazán has showed a great aptitude in the laboratory, and was quick to offer suggestions when problems were encountered. She showed diligence and neatness in completing her projects. She was enthusiastic to learn new techniques, and to obtain hands on experience with all the subject matters that she found in this training. I have to highlight that she is very active and she is a very hard worker. A last point I want to mark is her good social disposition, being very friendly with all the lab colleagues and very collaborative.
All these information is indicative of the quality of the research work carried out during this training and the personal characteristic of Ms. Almazan. Consequently and based on my knowledge of Tatiana, I'm very pleased to recommend her without hesitation, and I expect her to continue to establish a noteworthy reputation in research.
Prof. M.A. RodrigoDepartment of Chemical Engineering University of Castilla La Mancha
Department of Chemical Engineering. Faculty of Chemical Sciences. Universidad de Castilla La Mancha. Office 01. Enrique Costa Novella Building. Campus Universitario s/n 13071 Ciudad Real. SPAIN.
E-mail: Manuel.Rodriqo@uclm.es - Phone +34926295300 ext. 3411 - Fax +34926295318
Perla Tatiana Almazán Sánchez 133
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”HAEM CIRA ININ
Perla Tatiana Almazán Sánchez 134
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
UNIVERSIDAD AUTÓNOMA DEL ESTADO DE MÉXICO fi través de la
FACULTAD DE LENGUAS
Otorga la presente
CONSTANCIAA:
(PerCa Tatiana Almazán SánchezPor su participación en el CURSO DE COMPRENSIÓN DE CONVERSACIÓN llevado a
cabo en el Centro Interamericano de Recursos del Agua, CIRA del 8 de febrero al 7 de abril del año en curso, con una duración total de 30 horas.
México. Toluca, abril del 2016.
"PATRIA, CIENCIA Y TRABAJO"
‘2016, Año del 60 aniversario del Estado de Mexico
ENCUITA DUELEN: A'
Perla Tatiana Almazán Sánchez 135
“Tratamientos avanzados para la remoción de un colorante de origen textil”
té LOS ANGELES ARAUJO GÓNZ, desarrollo del Personal Académico
A: PERLA TATIANA ALMAZAN SANCHEZ
Por su participación en el curso "ESTADÍSTICA APLICADA A LAS CIENCIAS DEL AGUA " llevado a cabo en CENTRO INTERAMERICANO DE RECURSOS DEL AGUA, del
23 de septiembre al 21 de octubre de 2015, con una duración de 25 horas.
Toluca, México, 21 de octubre de 2015
DIDEPA
Otorga la presente
PATRIA, CIENCIA Y TRABAJO2015, Año del Bicentenario Luctuoso de José María Morelos y Pavón
Académico
M. en Psic. MAR A DDirectora de
La Secretaría de Docencia a través de la Dirección de Desarrollo del Personal Académico
Cons .anda
UAEM Universidad Autónoma del Estado de México
Perla Tatiana Almazán Sánchez 136
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ALMAZAN SANCHEZ PERLA TATLANA
Por su asistencia y participación en el “Curso-Taller para la elaboración de guías pedagógicas”, el cual fue impartido del 6 al 10 de julio de 2015, en el Departamento
de Educación Continua de esta Facultad con una duración de 25 horas.
Patria, Ciencia y Trabajo
Perla Tatiana Almazán Sánchez 137
UAEM CIRA
“Tratamientos avanzados para la remoción de un colorante de origen textil”
UAEM Universidad Autónoma del Estado de México
La Facultad de Química
Otorga la presente
ConstanciaA: Perla Tatiana Almazán Sánchez
por su participación como asistente en el curso: “Cálculo de Distribución de Corriente Secundaria”
que se llevó a cabo los días 9 y 10 de enero, con una duración de 10 hrs.
Toluca de Lerdo, Estado de México a 10 de enero de 2014
Patria, Ciencia y Trabajo“2014, 70 Aniversario de la Autonomía ICLA-UAEM”
Perla Tatiana Almazán Sánchez 138
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 139
“Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Universidad Autónoma del Estado de MéxicoUAEM
Otorga la presente
ConstanciaA: Perla Tatiana Almazán Sánchez
Por su participación como ponente en el 6T0. CURSO-TALLER
“TEMAS ACTUALES EN CIENCIAS DEL AGUA”Realizado del 14 al 15 de Noviembre del año en curso,
con una duración de 10 horas.Patria, Ciencia y Trabajo
“2013, 50 Aniversario luctuoso del poeta Heriberto Enriquez”
Dra. María Vicenta Esteller Alberich
Comité Organizador
Perla Tatiana Almazán Sánchez 140
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 141
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Perla Tatiana Almazán Sánchez 142
4 “Tratamientos avanzados para la remoción de un colorante de origen textil”UAEM CIRA ININ
Perla Tatiana Almazán Sánchez 143
“Tratamientos avanzados para la remoción de un colorante de origen textil”
10. ANEXOS
Perla Tatiana Almazán Sánchez 144
“Tratamientos avanzados para la remoción de un colorante de origen textil”
10.1 ANEXO 1
CÁLCULOS PARA CONSTRUCCIÓN DEL CONCENTRADOR SOLAR CPC-2D
Considerando una energía de 10 KJ/L para tratar 1 L de agua residual durante un
tiempo de tratamiento de 1 h (3600s), es posible calcular la potencia con la Ec. A1-1:
P = wj± s 2,78 w3600 s
(A1-1)
Debido a que sólo el 30% de la radiación solar puede concentrarse, y que de ese
30%, solo el 10% es del tipo UV, se obtiene una potencia total (PT), calculada con la Ec.
A1-2
PT = 2,7778 W
(0,3)(0,1)= 95,59 W (A1-2)
Tomando en cuenta que la irradiancia promedio (G0) en Toluca es del orden de
600 W/m2, se puede determinar el área de entrada del concentrador mediante la Ec. A1-
3:
A = —-^ s 0.15 m2Gü-T
(A1-3)
Como se aprecia en la Fig. A1-1, el área de entrada del concentrador se define
como A = 2aZ; fijando el valor de l = 0.45 m , se obtiene:
a = — = 0.17 m2Z
(A1-4)
Perla Tatiana Almazán Sánchez 145
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Debido a la forma del concentrador, el contendor del agua residual a tratar tendrá
las mismas dimensiones que el área de salida, tal y como lo muestra la figura 8.
Fig. A1- 1 Esquema del CPC para tratamiento de aguas residuales
La Ec. A1-5 permite calcular la longitud de apertura de salida del concentrador,
considerando un volumen de 1 L y una altura de la película del agua de 0.01 m:
a' = — = 0.11 m 2lh
(A1-5)
Utilizando la ecuación A1-6 y A1-7 de la sección 1.5.1, se calculó el factor de
concentración y el ángulo de aceptación, los cuales fueron de 1.54 y 40.39° (0.705 rad)
respectivamente.
C = — = 1.542a'l
(A1-6)
0 = sin-1 - = 40.39° = 0.705 rad c
(A1-7)
Considerando la Ec. A1-8 es posible determinar las ecuaciones paramétricas que
describen la parábola (A1-8 y A1-9):
Perla Tatiana Almazán Sánchez 146
“Tratamientos avanzados para la remoción de un colorante de origen textil”
r¿(t) = %(t) = 2a' (1+sin 0) cos(t+0)
1-sin t1) -e <t <--2e
2(A1-8)
x(t) = 0.366cos(t+0.704)
1-sin t0.303 (A1-9)
Con el parámetro t = [-0.705; 0.161], se graficaron los datos obtenidos de las
ecuaciones para obtener el perfil parabólico del CPC.
La Tabla A1 muestra los datos utilizados para la obtención de la parábola
empleando la Ec. A9, y la gráfica de la ecuación de la parábola está indicada en la Fig. 2A,
dichas parábolas sirvieron para dar el perfil parabólico del concentrador solar.
Finalmente, las dimensiones del concentrador solar fueron: L= 33 cm, Z= 45 cm,
2a=34 cm, 2a'= 22 cm y ft= 1 cm
Tabla A1- 1 Datos obtenidos a partir de la ecuación de la parábola.
xy
xygrados radianes grados radianes
9.218 0.161 -0.161 0.377 26.000 0.454 -0.454 0.74610.000 0.175 -0.175 0.389 27.000 0.471 -0.471 0.77711.000 0.192 -0.192 0.405 28.000 0.489 -0.489 0.81112.000 0.209 -0.209 0.422 29.000 0.506 -0.506 0.84613.000 0.227 -0.227 0.439 30.000 0.524 -0.524 0.88314.000 0.244 -0.244 0.457 31.000 0.541 -0.541 0.92115.000 0.262 -0.262 0.476 32.000 0.559 -0.559 0.96216.000 0.279 -0.279 0.496 33.000 0.576 -0.576 1.00517.000 0.297 -0.297 0.516 34.000 0.593 -0.593 1.05018.000 0.314 -0.314 0.537 35.000 0.611 -0.611 1.09819.000 0.332 -0.332 0.560 36.000 0.628 -0.628 1.14920.000 0.349 -0.349 0.583 37.000 0.646 -0.646 1.20221.000 0.367 -0.367 0.607 38.000 0.663 -0.663 1.25822.000 0.384 -0.384 0.632 39.000 0.681 -0.681 1.31823.000 0.401 -0.401 0.659 40.000 0.698 -0.698 1.38224.000 0.419 -0.419 0.686 40.391 0.705 -0.705 1.40825.000 0.436 -0.436 0.715
Perla Tatiana Almazán Sánchez 147
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Fig. A1- 2 Parábolas obtenidas a partir de los datos calculados para dar perfil parabólico al CPC-2D
Perla Tatiana Almazán Sánchez 148
“Tratamientos avanzados para la remoción de un colorante de origen textil”
10.2 ANEXO 2
CÁLCULO DE CAPACIDAD DE ADSORCIÓN DE LAS COLUMNAS POR
BOHART-ADAMS
Para efectuar estos cálculos, se consideró una concentración de ruptura de color y
carbono orgánico total (COT) de 100 U PtCo y 15 mg/L, respectivamente. Se tomaron en
cuenta los tiempos de ruptura a dichas concentraciones y se graficó utilizando la altura del
lecho de los adsorbentes utilizados (Mt-KSF, Mt-Fe-7 y AC-N).
Se obtuvo la ecuación de la recta y se calcularon las constantes del modelo de
Bohart-Adams empleando la pendiente y la ordenada al origen. Estos cálculos permiten
obtener una capacidad de adsorción (N0) por cada adsorbente considerando las tres alturas
de lecho utilizadas.
Mt-KSF3.0
2.5
2.0
0.5
0.0
y = 0.075x -4.3333 R2 = 0.9985
y = 0.0297x -2.6947 R2 = 0.9942
0 20 40 60 80 100 120 140 160 180
tb (min)
• Color •COT
Fig. A2- 1 Tiempo de ruptura vs altura de lecho de la columna usando Mt-KSF
Perla Tatiana Almazán Sánchez 149
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Mt-Fe-73.5
3.0
2.5
2.0
SJ 1.5
1.0
0.5
0.0
y = 0.0093x + 1.4323 R2 = 0.6568
y = 0.0075x + 1.1194 R2 = 0.8832
0 50 100 150 200
tb (min)
• Color •COT
Fig. A2- 2 Tiempo de ruptura vs altura de lecho de la columna usando Mt-Fe-7
AC-N
SJ
9.08.07.06.05.0 - 4.0 - 3.0 2.01.00.0
..•
y = 0.1843x + 1.981 R2 = 0.9429
0
y = 0.0118x + 0.9165 R2 = 0.8551
............... ...
20 40 60 80 100 120 140
tb (min)
• Color «COT
Fig. A2- 3 Tiempo de ruptura vs altura de lecho de la columna usando AC-N
Perla Tatiana Almazán Sánchez 150
“Tratamientos avanzados para la remoción de un colorante de origen textil”
Tabla A2- 1 Constantes de Bohart-Adams
Cb =100 U PtCo Cb =15 COT/L
N0 KBA N0 KBA
Constantes (U PtCo/L) (L/U PtCo min) (g/L) (L/ g min)
Mt-KSF 1.286E+01 5.393E-04 3.997E-01 8.360E-03
Mt-Fe-7 1.605E+00 1.643E-03 1.128E-01 8.729E-03
AC-N 3.171E+01 1.184E-03 1.801E-01 9.144E-03
Perla Tatiana Almazán Sánchez 151
“Tratamientos avanzados para la remoción de un colorante de origen textil”
11. REFERENCIAS
Perla Tatiana Almazán Sánchez 152
“Tratamientos avanzados para la remoción de un colorante de origen textil”
ABBASI, M. & ASL, N. R. 2008. Sonochemical degradation of Basic Blue 41 dye assisted by nanoTiO2 and H2O2.
Journal of Hazardous Materials, 153, 942-947.
AHARONI, C. & TOMPKINS, F. C. 1970. Kinetics of Adsorption and Desorption and the Elovich Equation. In: D.D.
ELEY, H. P. A. P. B. W. (ed.) Advances in Catalysis. Academic Press.
AHMAD, A. A. & HAMEED, B. H. 2009.Reduction of COD and color of dyeing effluent from a cotton textile mill by
adsorption onto bamboo-based activated carbon. Journal of Hazardous Materials, 172, 1538-1543.
ALBUQUERQUE, L. F., SALGUEIRO, A. A., MELO, J. L. D. S. & CHIAVONE-FILHO, O. 2013. Coagulation of
indigo blue present in dyeing wastewater using a residual bittern. Separation and Purification Technology, 104,
246-249.
AL-DEGS, Y.S., EL-BARGHOUTHI, M.I., EL-SHEIKH, A.H., WALKER, G.M., 2008. Effect of solution pH, ionic
strength, and temperature on adsorption behavior of reactive dyes on activated carbon. Dyes and Pigments 77,
16-23.
ALEKSIC, M., KUSIC, H., KOPRIVANAC, N., LESZCZYNSKA, D. & BOZIC, A. L. 2010. Heterogeneous Fenton
type processes for the degradation of organic dye pollutant in water — The application of zeolite assisted
AOPs. Desalination, 257, 22-29.
AMAR, N. B., KECHAOU, N., PALMERI, J., DERATANI, A. & SGHAIER, A. 2009. Comparison of tertiary treatment
by nanofiltration and reverse osmosis for water reuse in denim textile industry. Journal of Hazardous Materials,
170, 111-117.
AMIN, N. K. 2009. Removal of direct blue-106 dye from aqueous solution using new activated carbons developed from
pomegranate peel: Adsorption equilibrium and kinetics. Journal of Hazardous Materials, 165, 52-62.
APHA, AWWA, WEF, Standard Methods for the Examination of Water and Wastewater, 20th ed., APHA, Washington
D.C., 1998.
BALAN, D. S. L. & MONTEIRO, R. T. R. 2001. Decolorization of textile indigo dye by ligninolytic fungi. Journal of
Biotechnology, 89, 141-145.
BANIC, N., ABRAMOVIC, B., KRSTIC, J., SOJIC, D., LONCAREVIC, D., CHERKEZOVA-ZHELEVA, Z. &
GUZSVÁNY, V. 2011. Photodegradation of thiacloprid using Fe/TiO2 as a heterogeneous photo-Fenton
catalyst. Applied Catalysis B: Environmental, 107, 363-371.
BIGDA R.J., Consider Fenton's chemistry for wastewater treatment, Chem. Eng. Prog. 91 (1995) 62-66.
BOHART, G. S. & ADAMS, E. Q. 1920. SOME ASPECTS OF THE BEHAVIOR OF CHARCOAL WITH RESPECT
TO CHLORINE.1. Journal of the American Chemical Society, 42, 523-544.
BOUASLA, C., SAMAR, M. E.-H. & ISMAIL, F. 2010. Degradation of methyl violet 6B dye by the Fenton process.
Desalination, 254, 35-41.
BOZIC, M. & KOKOL, V. 2008. Ecological alternatives to the reduction and oxidation processes in dyeing with vat and
sulphur dyes. Dyes and Pigments, 76, 299-309.
BRILLAS, E., BAÑOS, M. A., CAMPS, S., ARIAS, C., CABOT, P. L., GARRIDO, J. A. & RODRIGUEZ, R. M. 2004.
Catalytic effect of Fe2+, Cu2+ and UVA light on the electrochemical degradation of nitrobenzene using an
oxygen-difussion cathode. New J. Chem, 28, 314-322
BUTRÓN, E., JUÁREZ, M. E., SOLIS, M., TEUTLI, M., GONZÁLEZ, I. & NAVA, J. L. 2007. Electrochemical
incineration of indigo textile dye in filter-press-type FM01-LC electrochemical cell using BDD
electrodes.ElectrochimicaActa, 52, 6888-6894.
Perla Tatiana Almazán Sánchez 153
“Tratamientos avanzados para la remoción de un colorante de origen textil”
C. CATRINESCU, C. TEODOSIU, M. MACOVEANU, J. MIEHE-BRENDLÉ, R. LE DRED, Catalyticwet peroxide
oxidation of phenol over Fe-exchanged pillared beidellite, WaterRes. 37 (2003) 1154-1160.
CAMESELLE, C., PAZOS, M. & SANROMÁN, M. A. 2005. Selection of an electrolyte to enhance the electrochemical
decolourisation of indigo.Optimisation and scale-up. Chemosphere, 60, 1080-1086.
CAÑIZARES, P., MARTÍNEZ, F., JIMÉNEZ, C., LOBATO, J. & RODRIGO, M. A. 2006. Coagulation and
Electrocoagulation of Wastes Polluted with Dyes. Environmental Science & Technology, 40, 6418 -6424.
CATRINESCU, C., ARSENE, D., APOPEI, P. & TEODOSIU, C. 2012. Degradation of 4-chlorophenol from wastewater
through heterogeneous Fenton and photo-Fenton process, catalyzed by Al-Fe PILC. Applied Clay Science, 58,
96-101.
CHEN, Q., WU, P., LI, Y., ZHU, N. & DANG, Z. 2009. Heterogeneous photo-Fenton photodegradation of reactive
brilliant orange X-GN over iron-pillared montmorillonite under visible irradiation. Journal of Hazardous
Materials, 168, 901-908.
CONAGUA (2011). Informe Estadísticas del agua en México, edición 2011,Comisión Nacional del Agua (Conagua),
Secretaría de Medio Ambiente yRecursos Naturales (Semarnat), p 38, p.117:
http://www.conagua.gob.mx/CONAGUA07/Publicaciones/Publicaciones/SGP-1-11-EAM2011.PDF
COTTET L, ALMEIDA C. A. P., NAIDEK N., VIANTE M.F., LOPES M. C., DEBACHER NA. Adsorption
characteristics of montmorillonite clay modified with iron oxide with respect to methylene blue in aqueous
media. Appl Clay Sci. 2014;95:25-31.
CRINI, G. 2006. Non-conventional low-cost adsorbents for dye removal: A review. Bioresource Technology, 97, 1061
1085.
COONEY, D. (1999).Adsorption design for wastewater treatment: CRC Press LLC, Boca Raton FL
DE D. CASQUERO-RUIZ, J., GUIL, J. M., DE D. LÓPEZ-GONZÁLEZ, J. & RUIZ-PANIEGO, A. 1988. Study of the
porous structure of active carbons by nitrogen adsorption and n-nonanepreadsorption.Carbon, 26, 647-652.
DE LA CRUZ, N., ESQUIUS, L., GRANDJEAN, D., MAGNET, A., TUNGLER, A., DE ALENCASTRO, L. F. &
PULGARÍN, C. 2013. Degradation of emergent contaminants by UV, UV/H2O2 and neutral photo-Fenton at
pilot scale in a domestic wastewater treatment plant. Water Research, 47, 5836-5845.
DENG, Y. & ENGLEHARDT, J. D. 2006. Treatment of landfill leachate by the Fenton process. Water Research, 40,
3683-3694.
DIAS, J. M., ALVIM-FERRAZ, M. C. M., ALMEIDA, M. F., RIVERA-UTRILLA, J. & SÁNCHEZ-POLO, M. 2007.
Waste materials for activated carbon preparation and its use in aqueous-phase treatment: A review. Journal of
Environmental Management, 85, 833-846.
DÍAZGÓMEZ-TREVIÑO, A. P., MARTÍNEZ-MIRANDA, V. & SOLACHE-RÍOS, M. Removal of remazol yellow
from aqueous solutions by unmodified and stabilized iron modified clay. Applied Clay Science.
DUFFIE, J. A. & BECKMAN, W. A. 2013. Solar Engineering of Thermal Processes, Wiley.
EL-NAAS, M. H., AL-ZUHAIR, S. & ALHAIJA, M. A. 2010. Removal of phenol from petroleum refinery wastewater
through adsorption on date-pit activated carbon. Chemical Engineering Journal, 162, 997-1005.
FAJERWERG, K., FOUSSARD, J.N., A. PERRARD, H. DEBELLEFONTAINE, Wet oxidation ofphenol by
hydrogen peroxide: the key role of pH on the catalytic behaviour of Fe-ZSM-5, Water Sci. Technol. 35 (1997)
103-110.
FAN, L., ZHOU, Y., YANG, W., CHEN, G. & YANG, F. 2008. Electrochemical degradation of aqueous solution of
Amaranth azo dye on ACF under potentiostatic model. Dyes and Pigments, 76, 440-446.
Perla Tatiana Almazán Sánchez 154
“Tratamientos avanzados para la remoción de un colorante de origen textil”
FREUNDLICH H.M.F. (1906). Über die adsorption in Losungen. Z. Phys. Chem. 57, 385-470.
FU, F., WANG, Q. & TANG, B. 2009. Fenton and Fenton-like reaction followed by hydroxide precipitation in the
removal of Ni(II) from NiEDTA wastewater: A comparative study. Chemical Engineering Journal, 155, 769
774.
GREENPEACE INTERNATIONAL, 2012, Hilos Tóxicos: Al desnudo exponiendo el papel de la industria textil en la
contaminación de los ríos de México
GUARALDO, T. T., ZANONI, T. B., DE TORRESI, S. I. C., GONQALES, V. R., ZOCOLO, G. J., OLIVEIRA, D. P.
& ZANONI, M. V. B. 2013. On the application of nanostructured electrodes prepared by Ti/TiO2/WO3
“template”: A case study of removing toxicity of indigo using visible irradiation. Chemosphere, 91, 586-593.
GUTIÉRREZ-SEGURA, E., COLÍN-CRUZ, A., SOLACHE-RÍOS, M. & FALL, C. 2012. Removal of Denim Blue from
Aqueous Solutions by Inorganic Adsorbents in a Fixed-Bed Column.Water, Air, &SoilPollution, 223, 5505
5513.
GUTIÉRREZ-SEGURA, E., SOLACHE-RÍOS, M. & COLÍN-CRUZ, A. 2009. Sorption of indigo carmine by a Fe-
zeolitic tuff and carbonaceous material from pyrolyzed sewage sludge. Journal of Hazardous Materials, 170,
1227-1235.
HAN, R., ZOU, L., ZHAO, X., XU, Y., XU, F., LI, Y. & WANG, Y. 2009. Characterization and properties of iron oxide-
coated zeolite as adsorbent for removal of copper(II) from solution in fixed bed column. Chemical Engineering
Journal, 149, 123-131.
HERNEY-RAMIREZ, J., VICENTE, M. A. & MADEIRA, L. M. 2010. Heterogeneous photo-Fenton oxidation with
pillared clay-based catalysts for wastewater treatment: A review. Applied Catalysis B: Environmental, 98, 10
26.
HO, Y. S. & MCKAY, G. 2003. Sorption of dyes and copper ions onto biosorbents. Process Biochemistry, 38, 1047
1061.
HO, Y.-S. 2006. Review of second-order models for adsorption systems. Journal of Hazardous Materials, 136, 681-689.
HSUEH, C. L., HUANG, Y. H., WANG, C. C. & CHEN, C. Y. 2005. Degradation of azo dyes using low iron
concentration of Fenton and Fenton-like system. Chemosphere, 58, 1409-1414.
INEGI (Instituto Nacional de Estadística y Geografía), Censos Económicos (2009). Fabricación de insumos, acabados
textiles y prendas de vestir 2008.
KADIRVELU, K., KAVIPRIYA, M., KARTHIKA, C., RADHIKA, M., VENNILAMANI, N. & PATTABHI, S. 2003.
Utilization of various agricultural wastes for activated carbon preparation and application for the removal of
dyes and metal ions from aqueous solutions.Bioresource Technology, 87, 129-132.
KARADAG, D., TURAN, M., AKGUL, E., TOK, S. & FAKI, A. 2007.Adsorption Equilibrium and Kinetics of Reactive
Black 5 and Reactive Red 239 in Aqueous Solution onto Surfactant-Modified Zeolite. Journal of Chemical &
Engineering Data, 52, 1615-1620.
KHELIFI, E., GANNOUN, H., TOUHAMI, Y., BOUALLAGUI, H. & HAMDI, M. 2008.Aerobic decolourization of
the indigo dye-containing textile wastewater using continuous combined bioreactors. Journal of Hazardous
Materials, 152, 683-689.
KHIM HOONG, C. 2010. Fixed bed sorption: Setting the record straight on the Bohart-Adams and Thomas models.
Journal of Hazardous Materials, 177, 1006-1012.
Perla Tatiana Almazán Sánchez 155
“Tratamientos avanzados para la remoción de un colorante de origen textil”
KURNIAWAN, T. A. & LO, W.-H. 2009. Removal of refractory compounds from stabilized landfill leachate using an
integrated H2O2 oxidation and granular activated carbon (GAC) adsorption treatment. Water Research, 43,
4079-4091.
KUSIC, H., KOPRIVANAC, N. & SELANEC, I. 2006. Fe-exchanged zeolite as the effective heterogeneous Fenton-
type catalyst for the organic pollutant minimization: UV irradiation assistance. Chemosphere, 65, 65 -73.
LAKSHMI, U. R., SRIVASTAVA, V. C., MALL, I. D. & LATAYE, D. H. 2009. Rice husk ash as an effective adsorbent:
Evaluation of adsorptive characteristics for Indigo Carmine dye. Journal of Environmental Management, 90,
710-720.
LANGMUIR, I. 1916. THE CONSTITUTION AND FUNDAMENTAL PROPERTIES OF SOLIDS AND LIQUIDS.
PART I. SOLIDS. Journal of the American Chemical Society, 38, 2221-2295.
LEGRINI, O., OLIVEROS, E. & BRAUN, A. M. 1993. Photochemical processes for water treatment. Chemical
Reviews, 93, 671-698.
LIU, W., ZHANG, J., ZHANG, C., WANG, Y. & LI, Y. 2010. Adsorptive removal of Cr (VI) by Fe-modified activated
carbon prepared from Trapa natans husk. Chemical Engineering Journal, 162, 677-684.
M.A. TARR, Fenton and modified Fenton methods for pollutant degradation, in: M.A. Tarr (Ed.), Chemical
Degradation Methods for Wastes and Pollutants — Environmental and Industrial Applications, Marcel
Dekker Inc., New York, 2003, pp. 165-200.
MALIK, P. K. & SAHA, S. K. 2003. Oxidation of direct dyes with hydrogen peroxide using ferrous ion as catalyst.
Separation and Purification Technology, 31, 241-250.
MANCY, RUDOLPH (2005), Química Orgánica simplificada, Ed. Reverté, España.
MANU, B. & CHAUDHARI, S. 2003. Decolorization of indigo and azo dyes in semicontinuous reactors with long
hydraulic retention time. Process Biochemistry, 38, 1213-1221.
MANUFACTURA (2013). 5 de cada 10 jeans que se venden en EU son mexicanos. 24 de mayo de 2013,
http://www.manufactura.mx/industria/2013/05/24/5-de-cada-10-jeans-que-se-venden-en-eu-son-mexicanos.
MARTIN, R.T., BAILEY, S.W., EBERL, D.D., FANNING, D.S., GUGGENHEIM, S., KODAMA, H., PEVEAR, D.
R., SRODON, J., WICKS, F.J., 1991.Report of the clay minerals society nomenclaturecommittee: revised
classification of claymaterials. ClaysClayMiner. 39 (3), 333-335.
MBONIMPA, E. G., VADHEIM, B. & BLATCHLEY III, E. R. 2012. Continuous-flow solar UVB disinfection reactor
for drinking water. Water Research, 46, 2344-2354.
MESQUITA, I., MATOS, L. C., DUARTE, F., MALDONADO-HÓDAR, F. J., MENDES, A. & MADEIRA, L. M.
2012. Treatment of azo dye-containing wastewater by a Fenton-like process in a continuous packed-bed reactor
filled with activated carbon. Journal of Hazardous Materials, 237-238, 30-37.
METCALF AND EDDY (2003).Wastewater engineering: Treatment and Reuse, 4th, N.Y., U.S.A., McGraw Hill Co.
Inc.
MEXICO TODAY (2011). Industria textil mexicana: un ajuste para su negocio. http://mexicotoday.org/article/mexican-
textile-industry-fit-your-business
MAHMOODI NM, SALEHI R, ARAMI M. 2011. Binary system dye removal from colored textile wastewater using
activated carbon: kinetic and isotherm studies. Desalination, 272, 187-195.
NAM, S., RENGANATHAN, V. & TRATNYEK, P. G. 2001. Substituent effects on azo dye oxidation by the FeIII-
EDTA-H2O2
NMX-AA-003-1980. Muestreo
Perla Tatiana Almazán Sánchez 156
“Tratamientos avanzados para la remoción de un colorante de origen textil”
NMX-AA-008-SCFI-2000. Determinación del pH
NMX-AA-028-SCFI-2001. Determinación de la demanda bioquímica de oxígeno en aguas naturales, residuales (dbo5)
y residuales tratadas.
NMX-AA-030-SCFI-2001. Determinación de la demanda química de oxígeno en aguas naturales, residuales y
residuales tratadas -
NMX-AA-036-SCFI-2001, determinación de acidez y alcalinidad en aguas naturales, residuales y residuales tratadas
NMX-AA-045-SCFI-2001. Determinación de color platino cobalto en aguas naturales, residuales y residuales tratadas
NMX-AA-072-SCFI-2001, determinación de dureza total en aguas naturales, residuales y residuales tratadas
NMX-AA-073-SCFI-2001. Determinación de cloruros totales en aguas naturales, residuales y residuales tratadas
NMX-AA-074-1981. Determinación del ion sulfato
NMX-AA-079-SCFI-2001. Determinación de nitratos en aguas naturales, potables, residuales y residuales tratadas
NOM-001-SEMARNAT-1996. Establece los límites máximos permisibles de contaminantes en las descargas de aguas
residuales en aguas y bienes nacionales como ríos, embalses naturales o artificiales y aguas costeras.
NOM-002-SEMARNAT-1996. Establece los límites máximos permisibles de contaminantes en las descargas de aguas
residuales a los sistemas de alcantarillado urbano y municipal,
NOM-003-SEMARNAT-1997. Establece los límites máximos permisibles de contaminantes para las aguas residuales
tratadas que se reusen en servicios al público.
NOM-CCA-014-ECOL/1993. Establece los límites máximos permisibles de contaminantes en las descargas de aguas
residuales provenientes de la industria textil a cuerpos receptores
OLIVEROS, E., LEGRINI, O., HOHL, M., MÜLLER, T. & BRAUN, A. M. 1997. Industrial waste water treatment:
large scale development of a light-enhanced Fenton reaction. Chemical Engineering and Processing: Process
Intensification, 36, 397-405.
OLLER, I., MALATO, S., SÁNCHEZ-PÉREZ, J. A., GERNJAK, W., MALDONADO, M. I., PÉREZ-ESTRADA, L.
A. & PULGARÍN, C. 2007. A combined solar photocatalytic-biological field system for the mineralization of
an industrial pollutant at pilot scale. Catalysis Today, 122, 150-159.
OTHMAN, I., MOHAMED, R. M., IBRAHIM, I. A. & MOHAMED, M. M. 2006. Synthesis and modification of ZSM-
5 with manganese and lanthanum and their effects on decolorization of indigo carmine dye. Applied Catalysis
A: General, 299, 95-102.
OTHMAN, I., MOHAMED, R. M., IBRAHIM, I. A. & MOHAMED, M. M. 2006. Synthesis and modification of ZSM-
5 with manganese and lanthanum and their effects on decolorization of indigo carmine dye. Applied Catalysis
A: General, 299, 95-102.
OTURAN, M., BRILLAS, E., Electrochemical Advanced Oxidation Processes (EAOPs) for Environmental
Applications, PortugaliaeElectrochimicaActa 25 (2007) 1-18.
PIGNATELLO, J. J. 1992. Dark and photoassisted iron(3+)-catalyzed degradation of chlorophenoxy herbicides by
hydrogen peroxide. Environmental Science & Technology, 26, 944-951.
RAMIREZ, J. H., MALDONADO-HÓDAR, F. J., PÉREZ-CADENAS, A. F., MORENO-CASTILLA, C., COSTA, C.
A. & MADEIRA, L. M. 2007. Azo-dye Orange II degradation by heterogeneous Fenton-like reaction using
carbon-Fe catalysts.Applied Catalysis B: Environmental, 75, 312-323.
SALGADO-TRÁNSITO, I., JIMÉNEZ-GONZÁLEZ, A. E., RAMÓN-GARCÍA, M. L., PINEDA-ARELLANO, C. A.
6 ESTRADA-GASCA, C. A. 2015. Design of a novel CPC collector for the photodegradation of carbaryl
pesticides as a function of the solar concentration ratio. Solar Energy, 115, 537-551.
Perla Tatiana Almazán Sánchez 157
“Tratamientos avanzados para la remoción de un colorante de origen textil”
SANROMÁN, M. A., PAZOS, M., RICART, M. T. & CAMESELLE, C. 2004. Electrochemical decolourisation of
structurally different dyes. Chemosphere, 57, 233-239.
SARRIA, V., DERONT, M., PÉRINGER, P. & PULGARIN, C. 2003. Degradation of a biorecalcitrant dye precursor
present in industrial wastewaters by a new integrated iron(III) photoassisted-biological treatment. Applied
Catalysis B: Environmental, 40, 231-246.
SECULA, M. S., CREfESCU, I. & PETRESCU, S. 2011.An experimental study of indigo carmine removal from
aqueous solution by electrocoagulation. Desalination, 277, 227-235.
SHEN, D., FAN, J., ZHOU, W., GAO, B., YUE, Q. & KANG, Q. 2009. Adsorption kinetics and isotherm of anionic
dyes onto organo-bentonite from single and multisolute systems. Journal of Hazardous Materials, 172, 99-107.
SIRÉS, I., GARRIDO, J. A., RODRIGUEZ, R. M., CABOT, P. L., CENTELLAS, F., ARIAS, C. & BRILLAS, E. 2006.
Electrochemical degradation of paracetamol from wastewater by catalytic action of Fe2+, Cu2+, and UVA light
on electrogenerated hydrogen peroxide. J. Electrochem. Soc. 153, D1-D9
SKOOG, D. A., WEST, D. M., HOLLER, F. J., CROUCH S. R. 2005. Fundamentos de Química Analítica. 8a Edición.
Thomson. México.
SLEIMAN, M., VILDOZO, D., FERRONATO, C. & CHOVELON, J.-M. 2007. Photocatalytic degradation of azo dye
Metanil Yellow: Optimization and kinetic modeling using a chemometric approach. Applied Catalysis B:
Environmental, 77, 1-11.
SOHRABI, M. R. & GHAVAMI, M. 2008. Photocatalytic degradation of Direct Red 23 dye using UV/TiO2: Effect of
operational parameters. Journal of Hazardous Materials, 153, 1235-1239.
SUDARJANTO, G., KELLER-LEHMANN, B. & KELLER, J. 2006. Optimization of integrated chemical-biological
degradation of a reactive azo dye using response surface methodology. Journal of Hazardous Materials, 138,
160-168.
SUN, J.-H., SUN, S.-P., WANG, G.-L.& QIAO, L.-P. 2007. Degradation of azo dye Amido black 10B in aqueous
solution by Fenton oxidation process. Dyes and Pigments, 74, 647-652.
TAN, B. H., TENG, T. T. & OMAR, A. K. M. 2000. Removal of dyes and industrial dye wastes by magnesium chloride.
WaterResearch, 34, 597-601.
TAPIA S., S., & DEL RIO P., J. A. (2009). Concentrador parabólico compuesto: una descripción opto-geométrica.
Revista Mexicana de Física, 55(55), 141-153.
TEUTLI-SEQUEIRA, A., MARTÍNEZ-MIRANDA, V., SOLACHE-RÍOS, M. & LINARES-HERNÁNDEZ, I. 2013.
Aluminum and lanthanum effects in natural materials on the adsorption of fluoride ions. Journal of Fluorine
Chemistry, 148, 6-13.
TSENG, R.-L., WU, F.-C. & JUANG, R.-S. 2010. Characteristics and applications of the Lagergren's first-order equation
for adsorption kinetics. Journal of the Taiwan Institute of Chemical Engineers, 41, 661-669.
TUNQ, S., GÜRKAN, T. & DUMAN, O. 2012. On-line spectrophotometric method for the determination of optimum
operation parameters on the decolorization of Acid Red 66 and Direct Blue 71 from aqueous solution by Fenton
process. ChemicalEngineeringJournal, 181 -182, 431-442.
VEDRENNE, M., VASQUEZ-MEDRANO, R., PRATO-GARCIA, D., FRONTANA-URIBE, B. A., HERNANDEZ-
ESPARZA, M. & DE ANDRÉS, J. M. 2012. A ferrous oxalate mediated photo-Fenton system: Toward an
increased biodegradability of indigo dyed wastewaters. Journal of Hazardous Materials, 243, 292-301.
VELEGRAKI, T. & MANTZAVINOS, D. 2015. Solar photo-Fenton treatment of winery effluents in a pilot
photocatalytic reactor. Catalysis Today, 240, Part A, 153-159.
Perla Tatiana Almazán Sánchez 158
“Tratamientos avanzados para la remoción de un colorante de origen textil”
VOLZONE, C. 2007. Retention of pollutant gases: Comparison between clay minerals and their modified products.
Applied Clay Science, 36, 191-196.
WAN NGAH, W. S., TEONG, L. C. & HANAFIAH, M. A. K. M. 2011. Adsorption of dyes and heavy metal ions by
chitosan composites: A review. Carbohydrate Polymers, 83, 1446-1456.
WANG, S. & PENG, Y. 2010.Natural zeolites as effective adsorbents in water and wastewater treatment. Chemical
Engineering Journal, 156, 11-24.
WENG, C.-H. & HSU, M.-C. 2008. Regeneration of granular activated carbon by an electrochemical process.
Separation and Purification Technology, 64, 227-236.
WINSTON, R. 1974. Principles of solar concentrators of a novel design. Solar Energy, 16, 89-95.
WONG, Y. & YU, J. 1999. Laccase-catalyzed decolorization of synthetic dyes. Water Research, 33, 3512-3520.
WU, F.-C., TSENG, R.-L. & JUANG, R.-S. 2009. Characteristics of Elovich equation used for the analysis of adsorption
kinetics in dye-chitosan systems. Chemical Engineering Journal, 150, 366-373.
WU, J.-S., LIU, C.-H., CHU, K. H. & SUEN, S.-Y. 2008. Removal of cationic dye methyl violet 2B from water by
cation exchange membranes. Journal of Membrane Science, 309, 239-245.
YAGUB, M.T., SEN, T.K., AFROZE, S., ANG, H.M., 2014. Dye and its removal from aqueous solution by adsorption: A review. Advances in Colloid and Interface Science 209, 172-184.
ZABNEVA, O. V., SMOLIN, S. K., KLIMENKO, N. A., SHVIDENKO, O. G., GRECHANIK, S. V. &
SINEL'NIKOVA, A. V. 2012. Structural and sorption properties of activated carbon modified with iron oxides.
Journal of Water Chemistry and Technology, 34, 264-270.
ZAGHBANI, N., HAFIANE, A. & DHAHBI, M. 2008. Removal of Safranin T from wastewater using micellar enhanced
ultrafiltration. Desalination, 222, 348-356.
ZAINAL, Z., HUI, L. K., HUSSEIN, M. Z., TAUFIQ-YAP, Y. H., ABDULLAH, A. H. & RAMLI, I. 2005. Removal
of dyes using immobilized titanium dioxide illuminated by fluorescent lamps. Journal of Hazardous Materials,
125, 113-120.
ZHANG, D., ZHOU, C.-H., LIN, C.-X., TONG, D.-S. & YU, W.-H. 2010. Synthesis of clay minerals. Applied Clay
Science, 50, 1-11.
ZHU, M.-X., LEE, L., WANG, H.-H. & WANG, Z. 2007. Removal of an anionic dye by adsorption/precipitation
processes using alkaline white mud. Journal of Hazardous Materials, 149, 735-741.
ZOLLINGER, H., Color Chemistry: Synthesis, Properties and Applications of Organic Dyes and Pigments, 3rd ed.,
Wiley-VCH, Weinheim, Germany, 2003
Perla Tatiana Almazán Sánchez 159